Panasonic SB-WA1501EB Bedienungsanleitung

ORDERNO. MD0406274C2

Active Subwoofer System

SB-WA1501EB / SB-WA1501EG

Colour

(S)... Silver Type

SPECIFICATIONS

Specification

SPEAKER SECTION

Type 1way, 1speaker system, Bass-

ref.

Woofer 17 cm conetype

Output sound pressure 80 dB/W(1m)

Frequencyrange 40-220 Hz (at -16 dB)

45-180 Hz (at -10 dB)

Dimensions(WxH xD) 209 x361 x463 mm

Mass Approx. 11.7kg

GENERAL

Power supply AC 230-240 V, 50Hz (EB)

AC 230 V, 50Hz (EG)

Power consumption 230 W

Note:

Specificationsare subject tochangewithout notice.

Mass and dimensionsare approximate.

SB-HT1501E-S consistsof :

SB-FS1501E-S x2, SB-PS1501E-S x2and SB-PC1501E-S x1

System : SC-HT1500 (EB) MusicCenter: SA-HT1500 (EB)

SatelliteSpeakers: SB-HT1501 (E)

ActiveSubwoofer: SB-WA1501 (EB)

System : SC-HT1500 (EG) MusicCenter: SA-HT1500 (EG)

SatelliteSpeakers: SB-HT1501 (E)

ActiveSubwoofer: SB-WA1501 (EG)

2004 PanasonicAVCNetworks Singapore Pte. Ltd. (RCB

Unauthorized copying and distribution isaviolation of law.

1. Safety Precautions

1.1. GENERALGUIDELINES

1. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

2. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

1.1.1. LEAKAGE CURRENTCOLD CHECK

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

equipment such as screwheads, connectors, control shafts, etc.

When the exposed metallicpart has areturn path to the chassis,

the reading shouldbe between 1M and 5.2 . / When the

exposed metal does not have areturn path to the chassis, the

reading must be . Fig. 1

1.1.2. LEAKAGE CURRENTHOTCHECK (See Figure1.)

1. Plug the AC cord directlyinto the AC outlet. Don not use an

isolation transformer for thischeck.

2. Connect a1.5k , 10 watts resistor, inparallel with a0.15 F

capacitors, between each exposed metallicpart on the set and a

good earth ground such as awater pipe, as showninFigure 1.

3. Use an AC voltmeter, with 1000 ohms/voltor more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 volts RMS. A

leakage current tester (Simpson Model 229 or equivalent) maybe

used to make the hot checks, leakage current must not exceed 1/2

milliamp. Incase ameasurement isoutside of the limits specified,

there isapossibilityof ashock hazard, and the equipment should

be repaired and rechecked before itisreturned to the customer.

2. Handling the Lead-free Solder

2.1. About lead free solder (PbF)

Distinction of PbF P.C.B. :

P.C.B.s (manufactured) using leadfree solderwill have a PbF stampon the P.C.B.

Caution:

-Pb free solder has ahigher melting point that standard solder;

Typicallythe melting point is50 -70°F (30 -40°C)higher. / Please

use ahigh temperature soldering iron. Incase of the soldering

iron with temperature control, please set itto 700 ± 20°F (370 ±

10°C).

-Pb free solder will tend to splash when heated too high (about

1100°F/600°C).

-When soldering or unsoldering, please completelyremove all of

the solder on the pins or solder area, and be sure to heat the

soldering points with the Pb free solder until itmelts enough.

3. Before Repair and Adjustment

Disconnect AC power, discharge PowerSupplyCapacitors C546, C547, C548, C549 through a

10 , 1 W resistortoground.

DO NOTSHORT-CIRCUITDIRECTLY (witha screwdriverblade, forinstance), as this may

destroysolidstate devices.

Afterrepairs are completed, restore powergraduallyusing a variac, toavoidovercurrent.

Current consumption at AC 230~240V, 50Hz inNO SIGNALmode shouldbe ~250 mA (EB).

Current consumption at AC 230V, 50Hz inNO SIGNALmode shouldbe ~250 mA (EG).

4. Protection Circuitry

The protection circuitrymayhave operatedif eitherof the following conditions are noticed:

-Nosound isheard when the power isturned on.

-Stops during aperformance.

The function of this circuitryis toprevent circuitrydamage if, forexample, the positive and

negative speakerconnection wires are “shorted”, orif speakersystems withanimpedance less

thanthe indicatedratedimpedance of the amplifierare used.

If this occurs, followthe procedure outlines below:

1. Turn off the power.

2. Determine the cause of the problem and correct it.

3. Turn on the power once againafter one minute.

Note:

Whenthe protection circuitryfunctions, the unit will not operate unless the poweris first turned

off and thenon again.

5. Connection of the Speaker Cables

-Besure to connect speaker cables before connecting the AC

mains lead.

-The load impedance of anyspeaker used with thisunitmust be 6 .

1. Connect with the included monaural connection cableto the

receiver or amplifier’ssubwoofer output terminal.

2. Connect the AC mains lead to the householdAC outlet.

6. Disassembly Procedure

“ATTENTION SERVICER”

Some chassis components mayhave sharpedges.

Be careful whendisassembling and servicing.

1. Thissection describes procedures for checking the operation of

the major printed circuitboards and replacing the main

components.

2. For reassemblyafter operation checks or replacement, reverse

the respective procedures.

Special reassemblyprocedures are described onlywhen required.

3. Select items from the following index when checks or

replacement are required.

6.1. Disassemblyflow chart

The following chart is the procedure fordisassembling the casing and inside parts forinternal

inspection whencarrying out the servicing.

To assemble the unit, reverse the steps showninthe chart below.

6.2. Disassemblyof the Speaker Unitand checking of the P.C.B.

6.2.1. Removal of the Subwooferand PowerAmpUnit

Step1: Remove all the screws.

Step2: Remove the stand base.

Step3: Remove all the screws fromthe bottomof the speakerunit.

Step4: Remove all the screws fromthe rearpanel’s speakerunit guide.

Step5: Remove the screws fromthe subwoofer.

Step6: Remove the 2 screws fromthe PowerAmpunit.

Step7: Pull out the PowerAmpunit as arrowshown.

(Note: Be careful of the attachwire at CN506).

Step8: Disconnect the connectorCN506.

6.2.2. Checking forthe majorPCBs

-Follow Steps 1to 8described inItem 8.2.1.

Steps 9 & 10: Remove 7 screws fromthe rearpanel.

Step11: Release the connectorCN507 and remove the rearpanel.

Step12: Remove the screws.

Steps 13 & 14: Remove the screws.

Step15: Place the PowerP.C.B and AC Inlet P.C.B. as shownforchecking.

-Checking for the Transformer P.C.B.

Step16: Remove the screws.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Subwoofer Handbücher

Panasonic

Panasonic SB-WA340 Bedienungsanleitung

Panasonic

Panasonic SB-W740 Bedienungsanleitung

Panasonic

Panasonic SB-WA100K Bedienungsanleitung

Panasonic

Panasonic SB-WA920PP Bedienungsanleitung

Panasonic

Panasonic SB-WA500PP Bedienungsanleitung

Panasonic

Panasonic SB-WA730PP Bedienungsanleitung

Panasonic

Panasonic SB-W40P Bedienungsanleitung

Panasonic

Panasonic Ramsa WS-A240 Bedienungsanleitung

Panasonic

Panasonic SB-WA933 Bedienungsanleitung

Panasonic

Panasonic SB-WA1000E Bedienungsanleitung

Panasonic

Panasonic SB-WA880 Bedienungsanleitung

Panasonic

Panasonic SBAS500 - SPKR,ACTIVE SUBWOOFE Bedienungsanleitung

Panasonic

Panasonic SB-W335EG Bedienungsanleitung

Panasonic

Panasonic SB-WA880 Bedienungsanleitung

Panasonic

Panasonic SB-WA870EB Bedienungsanleitung

Panasonic

Panasonic SB-WA935EE Bedienungsanleitung

Panasonic

Panasonic SB-WA50 Bedienungsanleitung

Panasonic

Panasonic Ramsa WS-A240 Bedienungsanleitung

Panasonic

Panasonic SB-WA885EE Bedienungsanleitung

Panasonic

Panasonic SB-WA101E Bedienungsanleitung

Panasonic

Panasonic SB-WA100 Bedienungsanleitung

Panasonic

Panasonic SBW500 - SUBWOOFER SYS Bedienungsanleitung

Panasonic

Panasonic SB-AS100 Bedienungsanleitung

Panasonic

Panasonic SB-WA520EB Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung