Panasonic SB-WA340EBS1 Bedienungsanleitung

ORDERNO. MD0310441C2

ActiveSubwooferSystem

SB-WA340EBS1

Colour

(S1)...SilverType

SPECIFICATIONS

Specification

Activesubwoofer

Type 1way, 1speakersystem, bass-

ref.

Woofer 17 cm conetype

Impedance 4

Outputsound pressurelevel 80 dB/W (1.0m)

Frequencyrange 40 Hz-220 Hz(-16 dB)

45 Hz-180 Hz(-10 dB)

Dimensions(W xHxD) 160 x450 x424 mm

Mass Approx. 12 kg

General

Powersupply AC230-240 V, 50 Hz

Powerconsumption 250 W

Powerconsumption in standby

mode 0.7W

Note:

Specificationsaresubjectto changewithoutnotice.

Mass and dimensionsareapproximate.

System :SC-HT1000EBS MusicCenter:SA-HT1000EBS

Frontspeakers:SB-PF1000P-S (x2)

Centerspeaker:SB-PC1000P-S (x1)

Surround speakers:SB-PS1000P-S (x2)

ActiveSubwoofer:SB-WA340EBS1

System :SC-HT1000EGS MusicCenter:SA-HT1000EGS

Frontspeakers:SB-PF1000P-S (x2)

Centerspeaker:SB-PC1000P-S (x1)

Surround speakers:SB-PS1000P-S (x2)

ActiveSubwoofer:SB-WA340EBS1

1. SafetyPrecautions

1.1. GENERALGUIDELINES

1. Whenservicing, observetheoriginal leaddress. Ifashortcircuit

isfound, replace all parts whichhavebeenoverheatedor

damagedbytheshortcircuit.

2. Afterservicing, see toitthat all theprotectivedevices suchas

insulation barriers, insulation papersshieldsareproperlyinstalled.

3. Afterservicing, make thefollowing leakagecurrentchecks to

preventthecustomerfrombeing exposedtoshock hazards.

1.1.1. LEAKAGE CURRENTCOLDCHECK

1. Unplug theACcordand connect ajumperbetweenthetwoprongs

on theplug.

2. Measuretheresistance value, withanohmmeter, betweenthe

jumperedACplug and eachexposedmetalliccabinet parton the

equipmentsuchas screwheads, connectors, control shafts, etc.

Whentheexposedmetallicparthas areturnpathtothechassis,

thereading shouldbebetween1M and 5.2 . / Whenthe

exposedmetal does nothaveareturnpathtothechassis, the

reading must be . Fig. 1

1.1.2. LEAKAGE CURRENTHOTCHECK (See Figure1.)

1. Plug theACcorddirectlyintotheACoutlet. Donotuse an

isolation transformerforthischeck.

2. Connect a1.5k , 10 watts resistor, inparallel witha0.15 F

capacitors, betweeneachexposedmetallicparton theset and a

good earthground suchas awaterpipe, as showninFigure1.

3. Use anACvoltmeter, with1000 ohms/voltormoresensitivity, to

measurethepotential across theresistor.

4. Check eachexposedmetallicpart, and measurethevoltageat

eachpoint.

5. Reverse theACplug intheACoutlet and repeat eachoftheabove

measurements.

6. Thepotential at anypointshouldnotexceed0.75 volts RMS. A

leakagecurrenttester(Simpson Model 229 orequivalent) maybe

usedtomake thehotchecks, leakagecurrentmust notexceed1/2

milliamp. Incase ameasurementisoutsideofthelimits specified,

thereisapossibilityofashock hazard, and theequipmentshould

berepairedand recheckedbeforeitisreturnedtothecustomer.

2. Handling the Lead-free Solder

2.1. Aboutleadfree solder(PbF)

Distinction ofPbF P.C.B. :

P.C.B.s(manufactured)using leadfree solderwill have aPbF stampon theP.C.B.

Caution:

-Pbfree solderhas ahighermelting pointthat standardsolder;

Typicallythemelting pointis50 -70°F(30 -40°C)higher. / Please

use ahigh temperaturesoldering iron. Incase ofthesoldering iron

withtemperaturecontrol, please set itto700 ±20°F(370 ±10°C).

-Pbfree solderwill tend tosplashwhenheatedtoo high (about

1100°F/600°C).

-Whensoldering orunsoldering, please completelyremoveall ofthe

solderon thepinsorsolderarea, and besuretoheat thesoldering

points withthePbfree solderuntil itmelts enough.

3. BeforeRepairand Adjustment

DisconnectACpower, dischargePowerSupplyCapacitorsC546, C547, C548, C549 through a10

, 1Wresistor toground.

DONOTSHORT-CIRCUITDIRECTLY(withascrewdriverblade, for instance), as thismay destroy

solidstatedevices.

Afterrepairsarecompleted, restorepowergraduallyusing avariac, toavoidovercurrent.

Currentconsumption atAC230-240V, 50HzinNOSIGNALmodeshouldbe~500 mA.

4. Protection Circuitry

Theprotection circuitrymay have operatedifeitherofthefollowing conditionsarenoticed:

-Nosound isheardwhenthepoweristurnedon.

-Sound stopsduring aperformance.

Thefunction ofthiscircuitryistopreventcircuitrydamageif, for example, thepositive and

negative speakerconnection wires are

“shorted”, or ifspeakersystemswithanimpedance less thantheindicatedratedimpedance of

theamplifierareused.

Ifthisoccurs, followtheprocedureoutlines below:

1. Turnoff thepower.

2. Determinethecause oftheproblemand correct it.

3. Turnon thepoweronce againafteroneminute.

Note:

Whentheprotection circuitryfunctions, theunitwill notoperateunless thepowerisfirstturned

off and thenon again.

5. Connection of the SpeakerCables

-Besuretoconnect speakercables beforeconnecting theACpower

supplycord.

-Theloadimpedance ofanyspeakerusedwiththisunitmust be4 .

-Besuretoconnect thecablefromtherightspeakertotheright

terminal and thecablefromtheleft speakertotheleft terminal.

1. Stripoff theoutercovering, and twist thecenterconductor. Make

surethebareendsofthewires arenotunravelled. (Iftheyare,

twist themtightagain.)

2. Insertthewiretotherearpanel oftheunitand close thelever.

Notes :

-To preventdamagetocircuitry, nevershort-circuitpositive(+)and

negative(-) speakerwires.

-Besuretoconnect onlypositive(red)wires topositive(+)terminals

and negative(black) wires tonegative(-) terminals.

6. DisassemblyProcedure

“ATTENTIONSERVICER”

Somechassiscomponentsmay have sharp edges.

Becareful whendisassembling and servicing.

1. Thissection describes procedures forchecking theoperation of

themajorprintedcircuitboardsand replacing themain

components.

2. Forreassemblyafteroperation checks orreplacement, reverse the

respectiveprocedures.

Special reassemblyprocedures aredescribedonlywhenrequired.

3. Select itemsfromthefollowing index whenchecks orreplacement

arerequired.

Contents

-DisassemblyoftheSpeakerUnit

-MainComponentReplacementProcedures

6.1. DisassemblyoftheSpeakerUnit

Step1:Remove 2screwsfrom therearpanel.

Step2:Remove all screws.

Step3:Remove theStand Base.

Step4:Remove all screwsfrom thespeakerbottom.

Step5:Pull thePower/AmpUnitas shown.

Step6:Release theconnector CN506 and pull outthePower/AmpUnit.

Step7:PushtheNetFramefrom twoholes insidetheunit.

Step8:Remove theNetFrame.

Step9:Remove all thescrews.

Step10:Remove theSpeaker.

Step11 &12:Remove all thescrews.

Step13:Release theconnector CN507.

Step14:Remove the2screws.

Step15 &16:Remove all thescrews.

Step17:Place thePowerPCB as shownfor checking.

Checking for ACInletPCB.

6.2. MainComponentReplacementProcedures

Inhaltsverzeichnis

Andere Panasonic Subwoofer Handbücher

Panasonic

Panasonic SB-WA101E Bedienungsanleitung

Panasonic

Panasonic SB-WA05E Bedienungsanleitung

Panasonic

Panasonic SB-WA340 Bedienungsanleitung

Panasonic

Panasonic SB-WA730GCP Bedienungsanleitung

Panasonic

Panasonic SB-WA530EB Bedienungsanleitung

Panasonic

Panasonic SB-WA17E Bedienungsanleitung

Panasonic

Panasonic SB-WA330GCS Bedienungsanleitung

Panasonic

Panasonic SB-WA100K Bedienungsanleitung

Panasonic

Panasonic SB-WA840 Bedienungsanleitung

Panasonic

Panasonic SB-WA530EB Bedienungsanleitung

Panasonic

Panasonic SB-W335EG Bedienungsanleitung

Panasonic

Panasonic SB-WA520EB Bedienungsanleitung

Panasonic

Panasonic SB-WA100 Bedienungsanleitung

Panasonic

Panasonic SB-W40P Bedienungsanleitung

Panasonic

Panasonic SB-AS40 Bedienungsanleitung

Panasonic

Panasonic SBW500 - SUBWOOFER SYS Bedienungsanleitung

Panasonic

Panasonic SB-WA50 Bedienungsanleitung

Panasonic

Panasonic SB-WA733P Bedienungsanleitung

Panasonic

Panasonic SBAS500 - SPKR,ACTIVE SUBWOOFE Bedienungsanleitung

Panasonic

Panasonic SB-WA730 Bedienungsanleitung

Panasonic

Panasonic SB-WA730PP Bedienungsanleitung

Panasonic

Panasonic SB-WA935EE Bedienungsanleitung

Panasonic

Panasonic SB-WA1501EB Bedienungsanleitung

Panasonic

Panasonic SB-WA730GCP Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung