Panasonic CZ-RTC4 Bedienungsanleitung

Panasonic Corporation

1006 Kadoma, Kadoma City, Osaka, Japan

Operating Instructions

Timer Remote Controller

Model No. CZ-RTC4

Installation Instructions

Separately Attached.

ENGLISH

Before operating the unit, read these operating instructions thoroughly and keep them for future

reference.

CV6233312187

Panasonic Corporation

http://www.panasonic.com

2(EN)

Preparations How to Use Setting Change When

Necessary

Page

Thank you for purchasing the

Panasonic timer remote controller.

Read the Operating Instructions

carefully for safe use. This

manual describes the Operating

Instructions of the timer remote

controller. Read this manual as

well as operating instructions

supplied with indoor units and

outdoor units.

Be sure to read the “Safety

Precautions” (P.3, 4) before

using.

Keep this manual with operating

instructions supplied with indoor

units and outdoor units in a safe

place.

Be sure to keep this manual in a

place easily accessible by users.

In the case of user change, be

sure to give this manual to the

new user.

NOTICE

The English text is the original

instructions. Other languages

are translation of the original

instructions.

CONTENTS

Safety Precautions...............................3

Part Names ..........................................5

• Control panel .......................................5

• Screen display .....................................6

Basic Operations..................................7

• How to Operate....................................7

• Setting the Present Time .....................9

Weekly Program Function.................10

• Checking the Weekly Timer ...............10

• Changing the Program Timer............. 11

• Deleting the Program Timer...............13

• Invalidating the Program Timer..........14

• Duplicating the Program Timer ..........15

• Before Asking Repare work ...............16

Outing Function .................................17

• Setting the Outing Function ...............18

Sleeping Function..............................19

ECONAVI Function.............................22

•

ON/OFF setting of ECONAVI function

...23

Troubleshooting.................................24

Speciﬁcations.....................................26

(EN)

Safety Precautions

CAUTIONS

This appliance is intended to be used by expert or

trained users in shops, in light industry and on farms, or

for commercial use by lay persons.

This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe

way and understand the hazards involved.

WARNING

Do not use this appliance in a potentially explosive

atmosphere.

• Do not operate with wet hands.

• Do not wash with water.

In case of malfunction of this appliance, do not repair by

yourself. Contact the sales or service dealer for repair.

In case of emergency, remove the power plug

from the socket or switch off the circuit breaker

or the means by which the system is isolated

from the mains power.

WARNING CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

This symbol refers to a hazard or unsafe

practice which can result in personal injury or

product or property damage.

Matters to be observed Prohibited matters

4(EN)

Note:

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

FCC Caution: To assure continued compliance, follow

the attached installation instructions. Any changes

or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority

to operate this equipment.

Safety Precautions

(EN)

987

Part Names

1 Operation indicator

Illuminates during operation. Blinks during alarm.

2 Start/Stop button

Starts/Stops operation.

3 Fan speed

Changing the fan speed.

4 Swing/Air direction

Use this button to set the auto swing or air direction to a speciﬁc angle.

5 Unit select

When more than one indoor unit is operated by one remote control unit, this button is used to

select a unit when adjusting the air direction.

6 Sleeping

7 Ventilation

Use this button when you installed a fan available in the market. Pressing this button turns on

and off the fan. When turning off the air conditioner, the fan will be also turned off.

8 Filter reset

Use this button to reset the ﬁlter sign. When is displayed, press this button after cleaning the

ﬁlter.

9 Timer setting buttons

10 Remote control sensor

Normally, the temperature sensor of the indoor unit is used to detect the temperature.

However, it is also possible to detect the temperature around the remote control unit.

11 Mode select

Pushing this button selects an operation mode.

12 ECONAVI

Use this button to turn on/off the ECONAVI Function.

13 Temperature setting buttons

Changing the temperature setting.

Control panel

6(EN)

2726

19 18 17 16 15 14 13 12 11 10

28 1 2 3

1Displayed if the selected feature was disabled during installation.

2Displayed when a mistake is made during timer setting.

3Appears when the timer program is being set.

4Indicates today’s day of the week.

5Displayed when the timer has been turned OFF.

6Timer program indication

: The indoor unit starts operation at the programmed time.

: The indoor unit stops operation at the programmed time.

7Displays the present time on a 24-hour clock. Also, displays settings in the various setting

modes.

8Appears when the time program is being set.

9Indicates the unit No. of the selected indoor unit.

10 Appears during the peak cut mode (Demand) if an electric heat pump (EHP) air conditioner is

used or during standby if a gas heat pump (GHP) air conditioner is used.

11 Appears when the fan of the indoor unit is stopped or in low fan speed.

12 The engine oil needs to be replaced. (Only when using a gas heat pump air conditioner.)

13 Appears when the maintenance function (monitoring sensor temperatures) is activated.

14 The indoor unit ﬁlter needs to be cleaned.

15 Appears during the sleeping function.

16 Appears when a fan available in the market is installed and is operating.

17 Switching operation modes is prohibited. (Switching to Auto mode is also prohibited.)

18 Remote control operation is restricted by a central control device.

19 Appears when the remote control sensor is used.

20 The selected fan mode is displayed.

21 Appears while in test operation.

22 Indicates the ﬂap position.

23 Indicates the set temperature.

24 Appears during the outing function.

25 Displays the selected operation mode.

(AUTO

/HEAT /DRY /COOL /FAN )

26 Appears when ECONAVI is being set to ON.

27 When inspection is required.

28 Appears with displaying 27 if there is a problem on ECONAVI.

Screen display

Part Names

(EN)

Basic Operations

How to Operate

Turn on the indoor unit before operation. See operating instructions of the indoor unit.

Start/Stop operation / Operation mode

1. Press [Start/Stop] to start operation.

2. Press the mode select button to select

the mode among AUTO , HEAT ,

DRY , COOL and FAN .

* Auto: The mode is automatically switched to

Cool or Heat to achieve the set temperature.

Set temperature

Press [ / ] to set the desired

temperature.

Cannot be set in Fan mode.

Temperature

Fan speed

Press the fan speed button to set the fan

speed.

: Automatically switches the fan speed.

: Low

: Medium

: High

Fan speed

Flap

Press the ﬂap button to adjust the ﬂap

position.

Flap

8(EN)

Note

If the heating performance is insufﬁcient in Low fan speed, change the fan

speed to Medium or High .

The temperature range that can be set varies depending on the model.

Temperature sensor detects temperature in the vicinity of the air inlet of the

indoor unit. The detected temperature slightly differs from the room temperature

depending on the installation condition. The set temperature is a guideline of

room temperature.

(EN)

1Press and hold [SET] for more than

2 seconds to enter the present day

and time setting mode.

Once you enter the setting mode,

“SETTING”, “▼”(day) and “time” ﬂash.

2Set “▼” to today’s day of the week.

Press [

▲

] to move “

▼

” (ﬂashing on the

display) in the order of: Su →Mo →Tu →....

Press [▼] to move it in the order of: Su →

Sa →Fr →....

Press [SET] to store.

3Press [▼/▲] to change the present

“hour” in the range of 0 to 23*1.

Set the present hour and press [SET].

The “hour” digits light up, and the “minute”

digits start ﬂashing.

*1If the clock uses the 12 hours AM/PM

setting, the hour is displayed in the range of

AM 1 to 12 / PM 1 to 12.

4Press [▼/▲] to change the present

“minute” in the range of 0 to 59.

Set the present minute and press [SET]. The

day and time are set and the unit ﬁnishes

the setting mode.

2 / 3 / 4 1 / 3 / 4

Note

If the present time is invalid, “– – : – –” is displayed. If the power failure occurs,

check if the set data of day and time are valid.

Setting the Present Time

Basic Operations

10 (EN)

Checking the Weekly Timer

• Set the weekly program assigning a given timer to each day of the week.

Maximum of 6 programs a day and 42 programs a week can be set.

Select the day and the TIMER number you want to program.

1Press [PROGRAM] to enter the

program conﬁrmation mode

“ ” and start setting.

Once you enter the program conﬁrmation

mode, the present day is indicated as

TIMER No. “1”.

2 / 31

TIMER No. 1-6

program CHeck

2Select the day.

Press [▼/▲] to move the “ ” horizontally on

the day to select.

Press [▲] to move “ ” (ﬂashing on the

display) in the order of: Su →Mo →Tu....

Press [▼] to move it in the order of : Su →

Sa →Fr....

“– – : – –” is displayed when the program is

not set.

Press [SET] to ﬁx the day.

3Select a Timer number.

Press [▼/▲] to select a TIMER No. from 1

to 6.

Press [▲] to move up from 1.

Press [▼] to move down from 6.

Weekly Program Function

Andere Handbücher für CZ-RTC4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Universalfernbedienung Handbücher

Panasonic

Panasonic URC-4914 Bedienungsanleitung

Beliebte Universalfernbedienung Handbücher anderer Marken

Pronto

Pronto Peel Bedienungsanleitung

GE 24929 Bedienungsanleitung

Radio Shack

Radio Shack Wireless Remote Control System Bedienungsanleitung

AUVIO

AUVIO Universal Home Theater Remote Bedienungsanleitung

Philips

Philips Icon SRU4106 Bedienungsanleitung

THOMSON

THOMSON ROC4309 Bedienungsanleitung

Philips

Philips pm625S Bedienungsanleitung

GE RM94931 Bedienungsanleitung

RCA

RCA RCU600WMS - Universal Remote Control Bedienungsanleitung

Blackweb

Blackweb BWB17AV002 Bedienungsanleitung

Marmitek

Marmitek DoorGuard 300 Bedienungsanleitung

Chunghop

Chunghop RM-L618 Bedienungsanleitung

GE RM24965 Bedienungsanleitung

Anderic

Anderic KTN828 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Bedienungsanleitung

Medion

Medion E74023 Bedienungsanleitung

intensity

intensity RM02A Bedienungsanleitung

GE RM24950 Bedienungsanleitung