Panasonic PV-V462 Bedienungsanleitung

ORDERNO. MKE0201001C1

VideoCassette Recorder

PV-V462 / PV-V4602 / PV-V4622 / PV-V4612S/ PV-V4022-K/

PV-V4522-K/ PV-V4612-K

SPECIFICATIONS

2002 Matsushita Kotobuki Electronics Industries Ltd. All rights

reserved. Unauthorizedcopying and distribution isaviolation of

law.

1. SAFETY PRECAUTIONS

GENERALGUIDELINES

1. IMPORTANTSAFETY NOTICE

Therearespecial components usedinthisequipmentwhichare

importantfor safety. These parts aremarkedbyinthe

SchematicDiagrams, CircuitBoard Layout, ExplodedViewsand

ReplacementParts List. Itisessential that these criticalparts

shouldbereplacedwithmanufacturer’sspecifiedparts toprevent

shock, fireor otherhazards. Donotmodifytheoriginal design

withoutpermission ofmanufacturer.

2. AnIsolation Transformershouldalwaysbeusedduring the

servicing ofVCR whose chassisisnotisolatedfrom theAC

powerline. Use atransformerofadequate powerrating as this

protects thetechnicianfrom accidents resulting inpersonalinjury

from electrical shocks. Itwill alsoprotect VCR from being

damagedbyaccidental shorting that mayoccur during servicing.

3. Whenservicing, observetheoriginal leaddress. Ifashortcircuit

isfound, replace all parts whichhavebeenoverheatedor

damagedbytheshortcircuit.

4. Afterservicing, see toitthat all theprotectivedevices suchas

insulation barriers, insulation papersshieldsareproperly

installed.

5. Afterservicing, make thefollowing leakagecurrentchecks to

preventthecustomerfrom being exposedtoshock hazards.

LEAKAGECURRENTCOLD CHECK

1. Unplug theACcord and connect ajumperbetweenthetwo

prongson theplug.

2. Measuretheresistance value, withanohmmeter, betweenthe

jumperedACplug and eachexposedmetalliccabinet parton the

equipmentsuchas screwheads, connectors, control shafts, etc.

Whentheexposedmetallicparthas areturn pathtothechassis,

thereading shouldbebetween1M and 5.2M . Whenthe

exposedmetal does nothaveareturn pathtothechassis, the

reading must beinfinity.

LEAKAGECURRENTHOTCHECK

(See figure 1.)

1. Plug theACcord directlyintotheACoutlet. Donotuse an

isolation transformerfor thischeck.

2. Connect a1.5k , 10 Wresistor, inparallel witha0.15 F

capacitor, betweeneachexposedmetallicparton theset and a

good earthground, as showninfigure1.

3. Use anACvoltmeter, with1k /V or moresensitivity, tomeasure

thepotential across theresistor.

4. Check eachexposedmetallicpart, and measurethevoltageat

eachpoint.

5. Reverse theACplug intheACoutlet and repeat eachoftheabove

measurements.

6. Thepotential at anypointshouldnotexceed0.75 V RMS. A

leakagecurrenttester(Simpson Model 229 or equivalent) maybe

usedtomake thehotchecks. Leakagecurrentmust notexceed1/

2mA. Incase ameasurementisoutsideofthelimits specified,

thereisapossibilityofashock hazard, and theequipmentshould

berepairedand recheckedbeforeitisreturnedtothecustomer.

Figure 1

2. PREVENTIONOF ELECTRO-STATICDISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor(solidstate)devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES)Devices. Examples of typical

ES devices are integratedcircuits, some field-effecttransistorsand semiconductor"chip"

components. The following techniques shouldbe usedto helpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybeforehandling anysemiconductor componentor

semiconductor-equippedassembly, drainoff anyESDon your

bodybytouching aknownearthground. Alternatively, obtainand

wearacommerciallyavailabledischarging ESDwrist strap,

whichshouldremoveelectrostaticchargefor potential shock

reasonsprior toapplying powertotheunitundertest.

2. Afterremoving anelectrical assemblyequippedwithES devices,

place theassemblyon aconductivesurface suchas aluminum

foil, topreventelectrostaticchargebuildup or exposureofthe

assembly.

3. Use onlyagrounded-tipsoldering iron tosolderor unsolderES

devices.

4. Use onlyanantistaticsolderremoval device. Somesolder

removal devices notclassifiedas "antistatic(ESDprotected)"can

generate electrical chargesufficienttodamageES devices.

5. Donotuse freon-propelledchemicals. These cangenerate

electrical charges sufficienttodamageES devices.

6. DonotremoveareplacementES device from its protective

packageuntil immediatelybeforeyou arereadytoinstall it. (Most

replacementES devices arepackagedwithleadselectrically

shortedtogetherbyconductivefoam, aluminum foil or

comparableconductivematerial).

7. Immediatelybeforeremoving theprotectivematerial from the

leadsofareplacementES device, touchtheprotectivematerial to

thechassisor circuitassemblyintowhichthedevice will be

installed.

CAUTION:Besureno powerisappliedtothechassisor circuit,

and observeall othersafetyprecautions.

8. Minimizebodilymotionswhenhandling unpackagedreplacement

ES devices. (Otherwise harmless motion suchas thebrushing

togetherofyour clothes fabricor thelifting ofyour footfrom a

carpetedfloor cangenerate staticelectricity(ESD)sufficientto

damageanES device).

"NOTEto CATVsysteminstaller:

This reminderis providedto call the CATVsysteminstaller’s attention to Article 820-22 of the

NEC thatprovides guidelines forpropergrounding and, inparticular, specifies thatthe cable

ground shall be connectedto the grounding systemof the building, as close to the point of

cable entryas practical."

3. OPERATIONGUIDE

4. SERVICE NOTES (PLEASE READ)

4.1. SERVICE NOTES

4.1.1. SIMPLIFIEDFAULT FINDINGDATA

implifiedSelf-Diagnostic Systemfacilitates finding the cause of the fault. A3-digitfaultcode

will be displayedinF.I.P.

The SimplifiedFaultfinding data is storedinthe MemoryIC (IC6005). This data is clearedafterit

is displayed, and thenthe POWER button is pressedback on.

1. Withpowerturnedoff, press CH DOWNbutton on VCR (for over3

secondsifVCR isnotinshutoff condition).

Fig. 1-1

2. Faultcode(3-digitnumber)will bedisplayedinF.I.P. as shown.

Fig. 1-2

Fig. 1-3

Fig. 1-4

Fig. 1-5

3. When1to4listedinLock codeoccurs, Lock data will bestored

intheMemoryIC(latest Lock data only).

Note:

1. Lock data will bekeptaftertheACCord isunplugged.

2. When1to4listedinLock codeoccursfor thefirst time, theVCR

does notgo intoVCR shut-off condition. Ifitoccursagainwithina

minute, theVCR goes intoVCR shut-off condition. Then, theVCR

stopsand all VCR function buttonsexceptfor powerbecomenon-

operational.

3. Lock data will beclearedat thefirst poweron operation afterlock

codeisdisplayedinFIP.

4.1.2. USAGE SCREENMODE

Function displayedon the TVmonitor:

-thetotal elapsed”Cylinderrotation ”time(inhours)

1. Withpowerturnedon and no cassette, press CH DOWNbutton on

VCR and 7keyon remote together.

(TheUSAGE SCREENwill bedisplayedon theTV Monitor.)

Fig. 2

Note:

1. Afterreplacing theCylinderUnit, press COUNTERRESETbutton

on remote inthismode. Total elapsed"Cylinderrotation" time(in

hours) will beclearedto0.

2. Torelease from UsageScreenMode, press anyoperation button

on VCR or insertacassette tapeinthismode. TheVCR will return

tonormal operation mode.

4.1.3. EEPROM IC(IC6005), MAINC.B.A. REPLACEMENT NOTE

Afterreplacing EEPROMIC (IC6005)orMainC.B.A., be sure to performthe "PGSHIFTER

ADJUSTMENT"inELECTRICALADJUSTMENTprocedures.

4.1.4. SERVICEPOSITION

4.1.4.1. Service Position

CAUTION:

HOTCIRCUIT(Primarycircuit) exists on theMainC.B.A.

Use extremecaretopreventaccidental shock whenservicing.

4.1.4.1.1. Service Position (1)

Fig. 3-1

4.1.4.1.2. Service Position (2-1)

(Normal Frame Model)

Fig. 3-2-1

4.1.4.1.3. Service Position (2-2)

(Wide Frame Model)

Fig. 3-2-2

Note:

1. Itispossiblethat theS-TabSW. maynotworkcorrectlyinService

Position (2-1), (2-2). (Recording cannotbedone). Inthiscase,

shorttheS-TabSW. Pinson thefoil sideoftheMainC.B.A. toturn

thisSW. on. Fig. 3-3

2. Place thetapebetweentheCassette UpAss’yand MainC.B.A. to

get astability.

Fig. 3-4

4.1.5. HOT CIRCUIT

Primarycircuitexists on the MainC.B.A.

This circuitis identifiedas "HOT"on the C.B.A. and inthe Service Manual. Use extreme care to

prevent accidental shock whenservicing.

4.1.6. SERVICEMODE

Inorderto inhibitdetection of the Supply& Takeup Photo Transistors, Reel Sensor, and

CylinderLock, press and holdFF button and CH DOWN buttons on VCR togetherover5

seconds inpoweroff condition.

Fig. 4-1

The powercomes on and the unitgoes into service mode.

Inthis mode, Mechanismmovement canbe confirmed. Whenremoving Cassette UpAss’y, it

canbe confirmedwithout a cassette.

Andere Handbücher für PV-V462

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Videorecorder-System Handbücher

Panasonic

Panasonic NV-FJ623EG Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-9668 Bedienungsanleitung

Panasonic

Panasonic AJ-SD255 - Professional Editing Video Cassete... Bedienungsanleitung

Panasonic

Panasonic OmniVision PV-QV200 Bedienungsanleitung

Panasonic

Panasonic PV-V4022-K Bedienungsanleitung

Panasonic

Panasonic NV-F70EA Bedienungsanleitung

Panasonic

Panasonic AG6540P - TIME LAPSE RECORDER Bedienungsanleitung

Panasonic

Panasonic PV-454S-K Bedienungsanleitung

Panasonic

Panasonic NV-DV2000 Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4660 Bedienungsanleitung

Panasonic

Panasonic NV-HV61GH Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-8661 Bedienungsanleitung

Panasonic

Panasonic AG5700P - SVHS Bedienungsanleitung

Panasonic

Panasonic NV-HD100EA Bedienungsanleitung

Panasonic

Panasonic NV-HV62GCS Bedienungsanleitung

Panasonic

Panasonic PV-8660 Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-8662 Bedienungsanleitung

Panasonic

Panasonic NV-HS880EG Bedienungsanleitung

Panasonic

Panasonic PV-V402 Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4611 Bedienungsanleitung

Panasonic

Panasonic AG710 - INDUSTRIAL VHS Bedienungsanleitung

Panasonic

Panasonic OmniVision PV-QV200 Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-HD1000 Bedienungsanleitung

Panasonic

Panasonic PV-8453 Bedienungsanleitung

Beliebte Videorecorder-System Handbücher anderer Marken

Toshiba

Toshiba M-662 Bedienungsanleitung

Sony

Sony GV-500 Primary Bedienungsanleitung

JVC

JVC HR-J282EU Bedienungsanleitung

Sony

Sony HDCAM-SR SRW5800 Bedienungsanleitung

Magnavox

Magnavox VRU242AT Bedienungsanleitung

Sony

Sony HVR-M10C Bedienungsanleitung

RCA

RCA VR634HF - Hi-Fi VCR Bedienungsanleitung

JVC

JVC HR-5910U Bedienungsanleitung

JVC

JVC HR-S8600EU Bedienungsanleitung

JVC

JVC HR-FS1U Bedienungsanleitung

Sharp

Sharp VC-H9888U Bedienungsanleitung

FUNAI

FUNAI LC-950 Bedienungsanleitung

Sharp

Sharp VC-S2000GM Bedienungsanleitung

Sony

Sony Video8 EV-A60 Bedienungsanleitung

Aiwa

Aiwa HV-E212 Bedienungsanleitung

JVC

JVC HR-J3006UM Bedienungsanleitung

GE VG4271 Bedienungsanleitung

RCA

RCA VR678HF Bedienungsanleitung