Panasonic WJ-ND300 Administrator Console Betriebsanleitung

Digital Disk Recorder

WJ-ND300 SATA conversion guide (Single)

22. Jan. 2009

System Solutions Company

ALARM

SUSPENDED ERROR TIMERREC

OPERATE

1-LINK/ACT-2

HDD 1 HDD 2 HDD 3

ESC

PULL

Network Disc Recorder

WJ-ND

300

SET

HDD 4

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

1. Outline

This guide describes how to convert the hard disk drive installed in the WJ-ND300, ND300A from PATA type to SATA type.

2. Preparation

Following items are required for the SATA conversion.

(1) Screwdriver

(2) Wrench for hexagonal nut (5.5m/m)

(3) 2 Cable ties

(4) SATA HDD: Refet to the HDD compatibility chart in the BIG-WEB site.

(5) SATA conversion kit (0E0A0060AA)

Part name Part number Quantity

SATA Board Ass’y JN30AJKY4A 4

SATA cables

K1V224Y20004 (SATA cable: Red, Power cable: Red/Blue)

1 each

K1V224Y20005 (SATA cable: Gray, Power cable: Red/Yellow)

K1V224Y20006 (SATA cable: Red, Power cable: White/Purple)

K1V224Y20007 (SATA cable: Gray, Power cable: White/Orange)

SATA board mounting bracket 3CA006029AAA 1

Heat sink 3KA001346AAA 1

Cool sheet 3KB001292AAA 1

Cord clamp FCA16 9

Hexagonal spacer 7 mm 1CJ001311AAA 3

Wafer-head screw 3AA000001AAA 2

Screw with washer XYN3+F8FJ 4

Caution label 3PC001235AAA 1

HDD Caution label 3PD003138BAA 1

SATA Cable label 3PD003960AAA 1

SATA label, small (for front) 3PD003840AAA 1

SATA label, large (for top) 3PD003841AAA 4

SATA Leaet 3TU001977AAA 1

SATA conversion leaet ND300PSATARB 1

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

3. Replacement Procedure

Important +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

• Power off the unit and disconnect from the mains power supply before carrying out this work.

• Do not detach the cable connecting the unit and the front panel while the HDD status indicators are still lit or until 30 seconds have

passed since the HDD status indicators went off.

• Protect the hard disk drives from static electricity.

• Do not stack them, or keep them upright.

• Do not use an electric screwdriver to x them. (Tightening torque: Approx. 0.49 N · m (5 kgf · cm))

• Avoid rapid changes in the temperature/humidity to prevent condensation. (Acceptable change: within 15°C/h (59 °F/h))

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

(1) Open the connectors cover on the front panel and remove the

xing screw.

Detach the front panel by sliding it after removing the screw.

(2) Disconnect the connector from the front panel.

(3) Disconnect four ATA cables and four HDD power cables

of all HDDs.

Note: When disconnecting the ATA cables, pull the pull-ring

slowly and straightforward.

ALARM

OPERATE

ALARM

SUSPENDED ERRORTIMERREC LINK1LINK2

HDD1HDD 2HDD3

ESC

NetworkDiscRecorder

WJ-ND

300

SET

HDD4

Connectorscover

Screw

Front panel

connector

Front panel

connector

Pull-ring

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

Important +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

The HDDs should be installed in the correct positions in the

order as shown right. Do not skip a drive position or reverse the

order of the HDD positions. Incorrectly placed drives will result

in the recorder not recognizing the extension unit or the drives.

HDD #1 slot : HDD1 HDD #2 slot : HDD2

HDD #3 slot : HDD3 HDD #4 slot : HDD4

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

(4) Remove 11 screws that x the top cover to the main unit,

and then remove the top cover.

(5) Remove eight screws xing the HDD unit, pull out the

unit.

(6) Remove the screws (four pieces each) xing the HDDs,

the sleeves and dampers and then remove the HDDs.

HDD 2

HDD 1

HDD 4

HDD 3

Inside the front cover

Damper

Sleeve

HDD unit

Top cover

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(7) Release the radiator fan cable from two cord clamps attached to the HDD Fan Ass’y, and disconnect respective Junction connectors,

and remove the HDD Fan Ass’y.

(8) Remove ve screws (3x wafer-head screw, 2x screw with

washer) xing the HDD Fan Ass’y and then remove the

HDD Fan Ass’y.

(9) Remove six screws (wafer-head screws) xing the HDD

unit guide rail, and remove three HDD unit guide rails.

FAN1

FAN2

HDD Fan Ass'y

screw with washer

wafer-head

screw

wafer-head

screw

HDD unit guide rail

six wafer-head

screws

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(10) Remove seven inside screws (wafer-head screws) and three front screws (binding screws) that secure the bottom plate, and remove

the bottom plate.

(11) Disconnect four HDD cables from the Main board, and release the cables from the HDD cable clamps, and then remove the HDD

cables.

Note: Discard the removed HDD cables.

(12) Disconnect four power cables from the DC/DC board, and

remove the power cables.

Note: Discard the removed HDD cables.

HDD unit

guide rail

Bottom plate

seven wafer-head

screws

Bottom plate

wafer-head

screw

binding screw

HDD cables

DC/DC board

Power cable

Heat Sink (for Main board)Main Board

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(13) Remove four screws (1x wafer-head screw, 3x screw

with washer) xing the Heat Sink (for Main board), and

remove the Heat Sink (for Main board).

Note: Discard the removed Heat Sink.

(14) Remove the cool sheet from the Main board

(Center of IC103).

Note: Discard the removed cool sheet.

(15) Remove the three spacers from the Main board.

Note: Discard the removed spacers.

(16) Secure the heat sink (for Main board) to the SATA board

mounting bracket with additional two screws.

Heat Sink

(for Main board)

SATA board

mounting bracket

cool

sheet

spacer

Heat Sink

(for Main board)

Main board

IC103

wafer-head

screw

screw with washer

additional two screws

(wafer-head screw)

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(17) Install three additional hexagonal spacers (7mm).

(18) Attach the new cool sheet to the Main board (Center of

IC103).

(19) Meeting the hexagonal spacers, install the SATA board

mounting bracket with four screws (1x wafer-head screw,

3x screw with washer).

(20) Install the SATA board with additional four screws.

Note: Circled tapped holes on the SATA connector side are not

necessarily screwed.

(21) Remove two cord clamps from the HDD Fan Ass’y, and attach four new cord clamps.

Note: Peel off the double-sided tape, not leaving any portion.

additional

Hexagonal spacer

three screws (7mm)

SATA board

mounting bracket SATA boards

additional four screws

(screw with washer)

New

cool sheet

Main board

IC103 wafer-head

screw

screw with washer

Remove

two cord clamps

Attach four new cord clamps

HDD Fan Ass'y

20mm

10mm 10mm

unites with a

left end.

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(22) Remove six cord clamps from the bottom of main unit

chassis.

(23) Attach ve new cord clamps.

Approx. 10mm

Approx. 80mm

Approx. 210mm

New cord clamps

Remove six cord clamps

WJ-ND300 SATA conversion guide (single) Maintenance guide

Panasonic ND300_SATAConversionGuideS_A

(24) Connect the power cables (red, yellow) to the CN4 of DC/

DC board, and pass them through the clamps 1, 2, 4 as

shown right.

(25) Connect the power cables (red, blue) to the CN3 of DC/DC board, and pass them through the clamps 1, 2, 3 as shown below.

(26) Connect the power cables (white, orange) to the CN6 of

DC/DC board, and pass them through the clamps 5, 6, 8 as

shown right.

(27) Connect the power cables (white, purple) to the CN5 of DC/DC board, and pass them through the clamps 5, 6, 7 as shown below.

DC/DC Board

CN4 Clamp 1, 2

(red, yellow)

Clamp 4

(yellow, gray)

Clamp 1, 2

(red, yellow,

red, blue)

CN3

CN4

Clamp 3

(red, blue)

CN3 CN4

CN6

Clamp 5

(white, orenge)

Clamp 6

(white, orenge)

Clamp 8

(orenge, gray)

CN3 CN4

CN5

CN6

Clamp 5

(white, orenge,

white, purple)

Clamp 6

(white, orenge,

white, purple)

Clamp 7

(red,

purple)

Andere Handbücher für WJ-ND300 Administrator Console

Inhaltsverzeichnis

Andere Panasonic Diktiergerät Handbücher

Panasonic

Panasonic RR-US350 Bedienungsanleitung

Panasonic

Panasonic RR-DR60 Bedienungsanleitung

Panasonic

Panasonic RR-US500 Bedienungsanleitung

Panasonic

Panasonic RR-US065 Bedienungsanleitung

Panasonic

Panasonic RR-US510 Bedienungsanleitung

Panasonic

Panasonic RR-US360 Bedienungsanleitung

Panasonic

Panasonic RRQR400 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic RQT9359-P Bedienungsanleitung

Panasonic

Panasonic RR-XS450 Bedienungsanleitung

Panasonic

Panasonic AJD440 - DVCPRO PLAYER Bedienungsanleitung

Panasonic

Panasonic RRUS591 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic RRQR270 Bedienungsanleitung

Panasonic

Panasonic AJ-P2C008HG Bedienungsanleitung

Panasonic

Panasonic RRQR100 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic RR-US430 Bedienungsanleitung

Panasonic

Panasonic WJHD100 - DIGITAL DISC RECORDE Bedienungsanleitung

Panasonic

Panasonic DMR-BCT765 Bedienungsanleitung

Panasonic

Panasonic RR-QR150 Bedienungsanleitung

Panasonic

Panasonic WJ-NX100/2E Betriebsanleitung

Panasonic

Panasonic RRUS550 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic RR-US006 Bedienungsanleitung

Panasonic

Panasonic RR-US050 Bedienungsanleitung

Panasonic

Panasonic WJRT416 - 16CH DIGITAL RECORDER Bedienungsanleitung

Panasonic

Panasonic RRQR240 - IC RECORDER Bedienungsanleitung

Beliebte Diktiergerät Handbücher anderer Marken

Sony

Sony ICD-UX533F Bedienungsanleitung

RCA

RCA VR5230 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Benutzerhandbuch

Sony

Sony TCM-400DV Bedienungsanleitung

LogTag

LogTag TREL30-16 Bedienungsanleitung

SVAT

SVAT CVP800 Bedienungsanleitung

Marantz

Marantz PMD620 Bedienungsanleitung

Zoom

Zoom H4next Bedienungsanleitung

Roland

Roland BR-900CD Bedienungsanleitung

JVC

JVC ProHD GY-HMZ1U Bedienungs- und Wartungshandbuch

Sanyo

Sanyo TRC-6400 Bedienungsanleitung

Tascam

Tascam DR-07 Bedienungsanleitung

Olympus

Olympus DW-90 Bedienungsanleitung

Sanyo

Sanyo ICR-B150 Bedienungsanleitung

Korg

Korg D4 Bedienungsanleitung

Sony

Sony ICD-SX46 - Ic Recorder Bedienungsanleitung

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Montageanleitung

DVS

DVS Pronto2K Montageanleitung