Panduit PATMFM4.0 Bedienungsanleitung
PATMFM4.0
PD29735A01
Rev. 02
August, 2020
PAT4.0 FLUSH MOUNT FIXTURE
OPERATION MANUAL
© Panduit Corp. 2020
Translation of the
Original Instructions
This manual contains instructions for the following:
PATMFM4.0
WARNING
•TO REDUCE THE RISK OF INJURY, USER
MUST READ INSTRUCTION MANUAL
Email:
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
www.panduit.com
Technical Support:
Tel: 1-800-777-3300
Panduit Europe • EMEA Service
Center
Almelo, Netherlands
Tel: +31 546 580 452 • Fax: +31 546 580
441
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
1
TABLE OF CONTENTS
TABLE OF CONTENTS..............................................................................................................................................1
1: INTRODUCTION..................................................................................................................................................3
2: SYSTEM SPECIFICATIONS....................................................................................................................................3
2A: PATMFM4.0 Table-Top Fixture ...........................................................................................................................3
2B: Fixture Tool Cage.................................................................................................................................................4
2C: EI Communication Cable .....................................................................................................................................5
2D: Tip Deflector........................................................................................................................................................6
2E: Tool Cavity Cover.................................................................................................................................................6
2F: Table-Top Template.............................................................................................................................................7
2G: Air Regulator.......................................................................................................................................................8
3: GENERAL POWER TOOL SAFETY WARNINGS ......................................................................................................9
3A: Work Area Safety....................................................................................................................................9
3B: Operational Safety Practices ................................................................................................................11
3C: Personal Safety .....................................................................................................................................11
3D: Power Tool Use and Care .....................................................................................................................12
3E: Service...................................................................................................................................................13
4: TECHNICAL SPECIFICATIONS............................................................................................................................. 13
4A: Air Supply ..........................................................................................................................................................13
4B: Environmental ...................................................................................................................................................14
5: INSTALLATION / SETUP ....................................................................................................................................14
5A: Take Inventory ..................................................................................................................................................14
5B. What’s Included.................................................................................................................................................14
5C. Modify Work Surface with Template................................................................................................................14
5D. PATMFM4.0 Fixture Assembly Installation(Ensure that the PAT4.0 system is off before installation). ............14
5E. Install PAT1M4.0/PAT1.5M4.0 Tool into Tool Cage ..........................................................................................15
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
2
5F. Install Tip Deflector onto The PAT1M4.0/PAT1.5M4.0 Tool..............................................................................17
5G. Mount Tool Cage Assembly onto Fixture Assembly ..........................................................................................17
5H. Electrical and Air Supply...................................................................................................................................21
5I. PHM Hose Installation........................................................................................................................................23
6: OPERATION......................................................................................................................................................25
6A: Start Up Checklist..............................................................................................................................................25
6B: Cable Tie Installation.........................................................................................................................................25
6C: Tip Deflector/Waste Receptacle........................................................................................................................29
7: MAINTENANCE ................................................................................................................................................ 30
7A: Preventative Maintenance................................................................................................................................30
8: TROUBLESHOOTING......................................................................................................................................... 31
8A: Error Message Troubleshooting........................................................................................................................31
9: BILL OF MATERIALS.......................................................................................................................................... 32
9A: WA29568E01 –Overlay Plate Assembly ...........................................................................................................32
9B: WA29569D01 –Tool Cage Assembly ................................................................................................................33
9C: WA29566C01 –Actuator Assembly...................................................................................................................33
9D: WA29567D01 –Electronics Enclosure Assembly ..............................................................................................34
9E: WA29653C01 –Air Regulator............................................................................................................................35
9F: Miscellaneous ....................................................................................................................................................35
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
3
1: INTRODUCTION
The PATMFM4.0 Table-Top Bench Mount Tool Fixture allows an operator to apply cable ties onto a wiring
harness with minimal strain. The fixture requires an existing PAT4.0 Fully Automatic Cable Tie Installation
System and can utilize both the PAT1M4.0 and PAT1.5M4.0 Handheld Tie Installation Tools. The PAT4.0
Hand Tool is mounted in the PATMFM4.0 fixture such that the work can be brought to the tool and actuated
simultaneously. Follow the step-by-step instructions below to install and operate the PATMFM4.0 Fixture.
NOTE: In the interest of higher quality and value, Panduit products are continually
being improved and updated.
Consequently, pictures may vary from the enclosed product.
2: SYSTEM SPECIFICATIONS
The Panduit Corporation PATMFM4.0 Table-Top Bench Mount Fixture consists of seven individual units:
The Table-Top Fixture, Fixture Tool Cage, EI Communication Cable, Tip Deflector, Tool Cavity Cover,
Table-Top Template and the PATMFM4.0 Air Regulator.
NOTE: Any substitution may cause serious damage to the system and/or injury to the operator.
2A: PATMFM4.0 Table-Top Fixture
The PATMFM 4.0 Table-Top Fixture is electrically and pneumatically controlled via an existing PAT4.0
System. A concealed electrical enclosure (Item E) manages these connections via Item(s) G,H and I.
Reference scales (Item(s) D) allow an operator to reference the distance relative to the PAT1M4.0 and
PAT1.5M4.0 jaw centers from either direction. An Actuation Paddle (Item C) lays flat in its storage position
until released via the spring-loaded latch (Item B). This paddle once released and in its operational position,
is actuated by the operator to preform work.
PATMFM4.0 Fixture General Overview:
A. Work Surface
B. Paddle Latch
C. Actuation Paddle
D. Reference Scale(s)
E. Electronics Enclosure
A
B
C
D
E
F
G
H
I
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
4
F. Electronics Enclosure Cover
G. Air-Regulator Input Fitting
H. EI Communication Port
I. Tool Cage air-line Output Quick-Connector
Table 2A: PATMFM4.0 Fixture Overall Specification
Dimension
Value
Length
19.32”(491mm)
Width
9.27” (235mm)
Height
6.53” (166mm)
Max Height Relative to Work Surface
1.79” (45mm)
2B: Fixture Tool Cage
The Fixture Tool Cage allows PAT1M4.0 and PAT1.5M4.0 Handheld Cable-Tie Installation Tools to be
mounted and installed into the PATMFM4.0 Table-Top Fixture. Installation of a Hand Tool is preceded by
removing the Rear Lower Tool Support (Item C) via the two thumbscrews (Item D). With the Rear Support
removed, a Hand Tool can be inserted and aligned relative to the Top and Bottom Front Tool Supports
(Item(s) A, B). Once a selected Tool is mounted into the Tool Cage and the Rear Support re-installed, the
Cage can be mounted onto the PATMFM4.0 Fixture, thus suspending the Tool such that only the top portion
of the Tool protrudes from the work surface. An airline (Item E) that exits the tool Cage is connected to the
PATMFM4.0 Fixture and delivers a controlled burst of air to the Actuation Trigger (Item G), engaging the
Tool Trigger (Item G) itself and beginning a cycle. Once complete, air is exhausted, the Actuation Trigger
retracts and the Tool is reset for a new cycle.
Fixture Tool Cage General Overview:
A
G
B
C
D
E
F
H
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
5
A. Front Upper Tool Support
B. Front Lower Tool Support
C. Rear Lower Tool Support
D. Retaining Thumbscrews
E. Tool Cage Airline
F. Tool Cage Retention Shoulder Screws
G. Actuation Trigger
H. Actuation Air Cylinder
Table 2B: Fixture Tool Cage Overall Specification
Dimension
Value
Length (Max-excluding airline)
4.63” (118mm)
Width (Max)
4.16” (106mm)
Height (Max)
6.28” (160mm)
2C: EI Communication Cable
The EI Communication Cable routes power and data between the PAT4.0 System and the PATMFM4.0
Fixture. This is a standard 25 Position D-Sub Male to Male connector cable that utilizes Philips head screws
on both connector ends for retention. The Cable delivers power to the PATMFM4.0 Fixture from the PAT4.0
System and relays cycle status and Actuation Paddle state back to the PAT4.0 System.
EI Communication Cable General Overview:
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
6
Table 2C: EI Communication Cable Overall Specification
Length
Width
Height
2m (6.56 ft)
2.17” (55mm)
0.65” (17mm)
2D: Tip Deflector
The Tip Deflector is similar to the Tip Collector originally provided with the PAT1M4.0 and PAT1.5M4.0
Handheld Tie Installation Tools. Instead of collecting the scrap produced, the Tip Deflector acts to divert
the waste under the work surface such that an appropriately located waste receptacle can be used under
said surface to collect scrap from multiple jobs/cycles without constant removal and clean up.
Tip Deflector General Overview:
Table 2D: Tip Deflector Overall Specification
Dimension
Value
Length
3.58” (91mm)
Width
2.09” (53mm)
Height
2.25” (57mm)
2E: Tool Cavity Cover
The Tool Cavity Cover is utilized when work is NOT preformed and a PAT1M4.0 or PAT1.5M4.0 Tool is
NOT installed within the Fixture Tool Cage (The Tool Cage can remain mounted onto the PATMFM4.0
Fixture). The Cavity Cover installs into the cavity, located on the top side of the PATMFM4.0 Fixture, in
order to restore the work surface area lost. This Cover aids in reducing the chance of materials falling
through this tool “cavity” and can be easily removed to resume work.
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
7
Tool Cavity Cover General Overview:
Table 2E: Tool Cavity Cover Overall Specification
Dimension
Value
Length
7.18” (182mm)
Width
2.46” (62mm)
Height
0.13” (3.3mm)
2F: Table-Top Template
The Table-Top Template is used prior to PATMFM4.0 Fixture installation in order to prepare a selected
work surface for the Fixture. A perimeter pattern of eight (8) total through holes and an aligned rectangular
pocket must be drilled and routed respectively in order to install the PATMFM4.0 Fixture successfully. A
proper work surface can be made from a variety of materials, either homogenous or engineered and the
PATMFM4.0 Fixture includes the necessary hardware for installation onto hardwood-based surfaces.
Reference the Minimum Work Surface Requirements table below for the minimum work surface dimensions
required to successfully install the PATMFM4.0 Fixture.
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
8
Table-Top Template General Overview:
Table 2F: Minimum Work Surface Specification
Dimension
Value
Length
22.0” (559mm)
Width
18.0” (457mm)
Depth
1.00” (25.4mm)
2G: Air Regulator
The PATMFM4.0 Air Regulator is designed to split and effectively “branch” the air regulator connection
already utilized by the PAT4.0 Fully Automatic Cable Tie Installation System. This branching air regulator
connects between the PAT4.0 System’s Air Regulator output and PAT4.0’s air input fitting to provide a
reduced operating pressure utilized by the PATMFM4.0 Fixture. The PATMFM4.0 Air Regulator is
adjustable and should be set to the recommended output specification (Table 4A) before connecting to and
operating the Fixture. Confirm this output pressure via the Air Regulator’s pressure gauge.
Air Regulator General Overview:
WORK SURFACE
DEPTH MUST BE
AT MIN. 1.00”
STEP 2:
REMOVE MAT’L
WITHIN SOLID
PERIMETER.
MIN. DISTANCE
FROM LEADING
EDGE OF WORK
SURFACE.
STEP 1:
DRILL x8 5/64”
THROUGH HOLES
INTO WORK
SURFACE.
(MARKED “A”)
TO PATMFM4.0
AIR INPUT FITTING
MIN: 40 PSI (2,8 bar)
MAX: DO NOT EXCEED 45 PSI (3,1 bar)
TO PDM4.0
AIR INPUT FITTING
TO PDM4.0 AIR
REGULATOR OUTPUT
MIN: 65 PSI (4,5 bar)
MAX: DO NOT EXCEED 85 PSI (5,8 bar)
MIN: 65 PSI (4,5 bar)
MAX: DO NOT EXCEED 85 PSI (5,8 bar)
© Panduit Corp.
2020
OPERATION MANUAL
PATMFM4.0
ENGLISH
9
3: GENERAL POWER TOOL SAFETY WARNINGS
The PAT4.0 Flush Table-Top Bench Mount System is pneumatically and electrically operated and
electronically controlled via an existing PAT Fully Automatic Cable Tie Installation System. Therefore,
certain safety practices must be followed.
WARNING
•Read all safety warning and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
•Save all warnings and instructions for future reference.
•The term “power tool” in the warnings refers to your main-operated (corded)
power tool or battery-operated (cordless) power tool.
Panduit Corp. recommends the fixture be used with all installed safety
features. Customer assumes all liability for injury that could result from
improper use of this fixture and responsibility for all necessary training to
ensure safe operation of this fixture.
•FOR INSTALLATION AND USE BY TRAINED PERSONNEL ONLY.
•IF ANY DAMAGE TO THE PRODUCT IS APPARENT OR SUSPECTED,
DO NOT USE THE PRODUCT. REFER PRODUCT TO QUALIFIED
SERVICE PERSONNEL.
•FCC WARNING: CHANGES OR MODIFICATIONS TO THE PRODUCT
COULD VOID THE USER’S AUTHORITY TO OPERATE THE PRODUCT.
3A: Work Area Safety
WARNING
DO NOT OPERATE POWER TOOLS IN EXPLOSIVE ATMOSPHERES, SUCH
AS IN THE PRESENCE OF FLAMMABLE LIQUIDS, GASES OR DUST.
Power tools create sparks which may ignite the dust or fumes.
Provide adequate ventilation around the product.
Andere Handbücher für PATMFM4.0
1
Inhaltsverzeichnis
Beliebte Leuchte Handbücher anderer Marken
Emos
Emos CLASSIC ZY1431T Bedienungsanleitung
Westinghouse
Westinghouse Outdoor Lighting Fixture Bedienungsanleitung
Hedler
Hedler C 12 silent Bedienungsanleitung
Blizzard Lighting
Blizzard Lighting Puck: CSI Bedienungsanleitung
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Bedienungsanleitung
Lightmaxx
Lightmaxx Shaft 5R Bedienungsanleitung
Cooper Lighting
Cooper Lighting Halo L3232E Bedienungsanleitung
Stageline
Stageline ODW-2410RGBW Bedienungsanleitung
Light Sky
Light Sky Tornado Series Bedienungsanleitung
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung
Lightolier
Lightolier Lytespan 83ED17S Bedienungsanleitung
Lightolier
Lightolier Calculite CS8226 Bedienungsanleitung