Paperfox H-1 Kurzanleitung
PAPERFOX –cutting, punching, folding www.paperfox.eu
Paperfox H-1
Cylinder cutting machine
Operational manual
V 1.1-en
H-1 Cylinder cutting machine
www.paperfox.eu 2
Warning
a) The Cylinder cutting machine may be utilized only in a closed room (office,
shop).
b) Prior to the machine utilization, definitely read all instructions.
c) To reduce the risk of injury, an inspection shall be essential, if the product
utilized in the vicinity of children.
Parameters
Dimensions: (L x W x H)
88 x 100 x 120 cm
Weight:
66 kg
Max. working width:
70 cm
Table size:
74 x70 cm
Distance between cylinders:
40..90 mm (Adjustable)
Distance between table and top cylinder:
20..70 mm (Adjustable)
Manufacturer:
Paperfox
H-2142 Nagytarcsa, Tessedik S. u. 48.
Cutting capacity
The Paperfox H-1 cylinder cutting machine is designed only for cutting sheet material
specified in parameters.
- You can cut simple shapes (for example a single circle or a rectangle) from card
up to 1000 g/m2 paper weight.
- More complicated shapes (for example 10 visit cards) can be cut from up to 250
g/m2 laminated cards.
- A very complicate shape (for example a puzzle from 300 g/m2 card with more
than 60 pieces) needs such a big cutting pressure which can’t be cut with this
simple machine.
- Corrugated paper usually can be cut easily with this machine.
- There are lot of different materials (plastic foils, leather, composite materials, and
textile) which can be cut with this cylinder cutting machine but they should test
individually if the machine can cut them or not.
H-1 Cylinder cutting machine
www.paperfox.eu 3
Machine parts
1. Cylinder setting screws. You can set the height of the top cylinder by turning
these screws. Top cylinder cover. The top cylinder is above this cover.
2. Machine table.
3. Handle
4. Machine frame
Usage of the Paperfox H-1 cylinder cutting machine
Place a VLPOM cutting plate or another hard plastic or metal plate on the machine
table. Put the cutting tool on the cutting plate with the cutting edges up. This plate
protects the soft machine table from be hurt by the back side of the cutting lines.
1
2
3
4
Machine table
VLPOM cutting plate
Cutting tool
Paper stops
H-1 Cylinder cutting machine
www.paperfox.eu 4
If the tool has parallel lines with the cylinder the place the tool angled on the table.
In this way you can avoid the unnecessary stress in the machine which occurs when
the machine has to cut a long line at once.
You can stick paper stops to the tool to position the sheet to cut. Stick a piece of card
on soft foam like on the picture.
Place a VLPOM cutting plate on the sheet which you want to cut.
Now you can set the optimal height of the cylinder. Lift up the cylinder with the
cylinder setting screws so that the tool with the plates could pass under the cylinder
without touching it. Then move the cylinder down so that it touches the cutting plate.
Paper sheet
Paper stops
Plastic or metal plate
under the cutting tool
Cutting plate
H-1 Cylinder cutting machine
www.paperfox.eu 5
Test the cutting result and in small steps increase the cutting pressure with the
setting screws until the machine cuts the whole shape perfectly.
You can use the machine for cutting in booth direction, but you can achieve better
accuracy if you use it always in the same direction.
Inhaltsverzeichnis
Andere Paperfox Cutter Handbücher
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
