Parallax PowerPal Bedienungsanleitung
Web Store: www.parallax.com
Tutorials: learn.parallax.com
Sales: sales@parallax.com
Tech Support: support@parallax.com
Office: (916) 624-8333
Educator Hotline: (916) 701-8625
Sales: (888) 512-1024
Tech Support: (888) 997-8267
PowerPal Selectable Voltage 3-Amp Breadboard
Power Supply (#32133)
The PowerPal is a breadboard-friendly 3A power supply module that allows you to select from
four different output voltage levels. It’s ideal for regulang power to the Propeller FLiP Try-it Kit
or other breadboard based projects along with a baery pack or wall-mount supply. It comes
with two sturdy 2x2 headers which plug directly into the breadboard rail. Through-hole pads are
provided that allow the user to oponally add an addional VOUT header or on-off switch
leads.
Features
●Rotary switch for user-selectable voltage output choices: 3.3 V, 5 V, 6 V, 7.5 V
●3 Amp connuous load switching power supply
●4 Amp peak surge rang is ideal for servo motors
●Barrel Jack or 0.1 inch pitch headers for 5-16 VIN
●Through-hole pads for oponal On/Off switch leads
●Green power-status LED
●Over-current and over-voltage protecon
●Over-temperature and short-circuit protecon
●0.1 inch (2.6 mm) diameter mounng hole
●All headers on a 0.1 inch (2.54 mm) grid
Copyright © Parallax Inc.
PowerPal Module ((#32133)
v1.0 11/20/2018 Page 1 of 6
Key Specifications
●Voltage input requirements: +5 to +16 VDC
●Voltage output selectable by user: 3.3V, 5V, 6V, or 7.5V
●Voltage output tolerance: Typically 2% at a 2A load, 3% at a 4A peak load
●Current rang: constant load 3 A; absolute peak 4 A
●Nominal switching frequency: 770 KHz
●Efficiency: up to 95%
●Operang temperature: -13 to +185 °F (-25 to +85 °C)
●Dimensions: PCB 1.5 x 1 inch (39 x 24 mm); 0.1 inch (2.6 mm) mounng hole
Feature Descriptions
Read the full explanaon of each labeled feature on the pages that follow this diagram.
Copyright © Parallax Inc.
PowerPal Module (#32133)
V1.0 11/20/2018 Page 2 of 6
1) Rotary Voltage Output Selector
Select an output voltage (VOUT) using a small screwdriver to rotate the arrow. The markings on
the rotary selector and the voltage are shown on the back of the PowerPal:
0 = 3.3V, 1 = 5V, 2 = 6V, 3 = 7.5V
While rotang the voltage selector between opons, the output voltage will be limited to about
1.8V and the VOUT LED will switch off to signal that the voltage selecon is not valid.
Take care when changing voltages! If your project expects 3.3V, but you select
7.5V even briefly, it may cause significant damage!
Always unplug the external power supply while changing voltage. We strongly suggest
unplugging the PowerPal from the breadboard and testing the VOUT setting with a
multimeter before connecting the PowerPal to your project, especially if you have any doubts
about the module or your power supply.
2) VIN Access Header
The VIN Header is a 0.1” pitch 3-pin header. To provide some polarity protecon for the user,
the two outer pins are negave, and the center pin is posive.
The 3-pin VIN header is connected directly to the DC Jack, and so care should be taken not to
supply power into the PowerPal through both the DC Jack and the 3-pin VIN header at the same
me.
Located between the DC Jack and 3-pin VIN header are two addional unpopulated + VIN
through-hole pads. These do not have any headers installed, and are intended for advanced
users who might want to install alternave connectors here. If you not need these, then please
ignore them!
3) VOUT ON LED
The green VOUT ON LED will light up when the rotary voltage output selector is set to one of
the four posions, and VOUT is acve. The brightness will vary depending on the output voltage
selected.
If the PowerPal detects an over-current condion, the VOUT ON LED will start blinking rapidly to
indicate a fault. If this occurs, disconnect power immediately and invesgate.
If the VOUT ON/OFF pads are shorted together, the VOUT ON LED will go off, as the output is
disabled.
Copyright © Parallax Inc.
PowerPal Module (#32133)
V1.0 11/20/2018 Page 3 of 6
4) VOUT Breadboard Headers
The PowerPal has two blocks of 4-pin headers posioned to allow inseron directly into the
breadboard power rail. The top pins are all posive voltage, and the boom row of pins (nearest
the board edge) are negave GND. The GND pins are idenfied by a white square around the
pads, both on the top and the boom of the pcb.
CAUTION! Before connecting power to the PowerPal, ensure that it is oriented
in the breadboard, such that the positive and negative outputs match the
circuit. Use color-coded wires and, if available, breadboard markings, to
differentiate VOUT and GND.
5) VOUT Access Header Pads
Located between the breadboard headers are a set of 3-pin through-hole pads that allow users
to fit a custom VOUT connector. The pads are spaced at a 0.1” pitch.
The center pin is posive, and the two outer pins negave/GND. The GND pins are idenfied on
both sides of the PCB by the white silk square around the pad.
6) VIN DC Jack
The DC Jack accepts a 2.1mm center-posive barrel plug. It is compable with many different
power source opons, including wall-mount power supplies and baery packs sold by Parallax
Inc.
The jack socket is connected directly to the VIN Header pins, located behind the DC Jack. The
dual connecon opon allows you to supply power through one, and source power from the
other. This might be useful to power high-voltage servo motors at baery supply voltage, while
PowerPal VOUT could be set to provide a lower voltage to your microcontroller and the rest of
your project’s circuits.
If your project required two PowerPals, you can power them both from one DC-Jack by linking
the VIN headers together with a short 3-pin jumper cable (751-00010).
WARNING! DO NOT connect a power input source to both the DC Jack and VIN
headers at the same time!
Copyright © Parallax Inc.
PowerPal Module (#32133)
V1.0 11/20/2018 Page 4 of 6
7) Switching Power Supply
The center area of the PowerPal pcb contains the switching power supply IC and supporng
components.
CAUTION! Components will become HOT when supplying high current loads!
TIP! The PCB is designed to act as heatsink, and the reverse of the PCB features
a continuous 2 oz copper ground plane which will become warm in normal use.
The PowerPal uses a switching buck regulator to efficiently drop VIN to the user selected VOUT
voltage.
It is not possible to output voltage larger than the input voltage, and the available output
current will depend on the input current. The output voltage will start to drop once you exceed
the power (voltage or current) available from your input power supply.
To minimise output voltage drop when powering high current (>2A) loads, ensure that VIN is at
least 1.5V more than your required VOUT.
8) Mounting Hole
The mounng hole is 0.1 inch (2.6mm) diameter, with clearance around up to 0.2 inches
(5.4mm), suitable for M2.5 or #3 mounng hardware .
The hole has no electrical connecon, but care should be taken when using metal fixings, and a
Nylon washer is recommended.
The locaon of the hole makes it convenient to fix a 12mm (15/32”) long nylon spacer, which
would act as a leg to support the PowerPal when inserted into a breadboard. Example: Digi-Key
part numbers: 1772-2059-ND (12mm Nylon spacer) and 36-29331-ND (6mm Nylon screw)
9) VOUT On/Off Pads
These oponal through-hole pads allow remote control of the VOUT state. When the on/off pins
are shorted together, VOUT will be switched off. The pads accept a 0.1” pitch 2-pin header.
VOUT ON/OFF could be controlled by a simple switch, or electronically by driving the ON/OFF
signal pin low using a microcontroller. The ground pin is surrounded by a white silkscreen
marking, and the signal pin is not.
Copyright © Parallax Inc.
PowerPal Module (#32133)
V1.0 11/20/2018 Page 5 of 6
PCB Dimensions
Revision History
Version 1.0: original release.
Copyright © Parallax Inc.
PowerPal Module (#32133)
V1.0 11/20/2018 Page 6 of 6
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Parallax Stromversorgung Handbücher
