Paramount Fitness ECO POOL 006-527-6316 Series Bedienungsanleitung

AUTOMATIC IN-FLOOR CIRCULATION SYSTEM

INSTALLATION

8175 W. Buckeye Rd., Phoenix, AZ 85043

Toll Free: 1.800.621.5886 • Phone: 480.893.7607 • Fax: 480.753.3397

[email protected] • www.1Paramount.com

US and Foreign patents and patents pending

see www.1paramount.com/support/patent-numbers/

Paramount products are designed by Paramount in Phoenix, Arizona, United States of America

ECOPOOL RIBBED BODY SYSTEM

Item Number: 006-527-6315-XX

Includes:

(1) Two-Port Four-Gear Valve

(3) Ribbed Bodies with Cap

(3) Nozzles

(3) Riser Pipes

(1) Nozzle Tool

ECOPOOL SMOOTH BODY SYSTEM

Item Number: 006-527-6316-XX

Includes:

(1) Two-Port Four-Gear Valve

(3) Smooth Bodies with Cap

(3) Nozzles

(3) Riser Pipes

(1) Nozzle Tool

Please indicate your color choice by placing the appropriate color code in place of the “XX"

at the end of the part number.

White-01 Gray-02 Black-03 Light Blue-06 Beige-07 Light Gray-08

ECOPOOL EQUIPMENT AND PLUMBING SCHEMATIC

1 2

PUMP

48D.E.

SAND 4.9

MIN.FILTER

CART. 150

HEATER

optional

RETURNS NOZZLES

CANISTER

MAIN DRAIN

SKIMMER

1 2

MIN.3'

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

1 1

2 2 2

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

MIN.3'

111

2 2 2

1 2

PUMP

48D.E.

SAND 4.9

MIN.FILTER

CART. 150

HEATER

optional

RETURNS NOZZLES

CANISTER

MAIN DRAIN

SKIMMER

1 2

MIN.3'

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

1 1

2 2 2

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

MIN.3'

111

2 2 2

1 2

PUMP

48D.E.

SAND 4.9

MIN.FILTER

CART. 150

HEATER

optional

RETURNS

NOZZLES

CANISTER

MAIN DRAIN

SKIMMER

1 2

MIN.3'

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

1 1

2 2 2

2" COMES IN

FROM FILTER

3' MINIMUM

R RR

MIN.3'

111

2 2 2

VALVE PLUMBING SCHEMATIC

2 PORT WATER VALVE

1. Floor #1

2. Wall #2

Note: If EcoPool includes SwingJets #2 wall

ﬁttings must be 1½" female threaded ﬁttings with

no inside restrictions.

VALVE PLUMBING SCHEMATIC

2 PORT WATER VALVE

Min. Pump Curve

50 GPM @ 60 TDH

Min. Filter Size

36 SQ. FT. DE = 72 GPM

3.1 SQ. FT SAND = 60 GPM

100 SQ. FT. CARTRIDGE = 75 GPM

Additional features added to pool equipment

such as in-line feeders, water falls, etc., may

change the ﬂow requirements. Changes in ﬂow

requirements may require a higher GPM pump

and larger ﬁltration

CENTER DEEP END DEEP

WATER VALVE INSTALLATION

AGGER 3" MINIMUM

NOTICE: All pipe ﬁttings MUST be staggered.

PARTS NEEDED FOR ASSEMBLY

OPTION ONE

• (2) 2”X15” PVC PIPE (port 1,2)

• (1) 2”X18” PVC PIPE (port inlet)

• (3) 2” SLIP 90° ELBOWS

• Set in trench 15 “ deep X 12” wide

1. Remove clamp

2. Lift off dome (save O-ring)

3. Remove pressure gauge and knob from

inside valve housing assembly

4. Pipes and valve base should be treated with

primer

5. Make sure pipes are glued all the way into

the stop. Be careful not to allow glue to run

into module area.*

6. The center port is the inlet to the valve and

should be approximately 3” longer than the

perimeter pipes.

7. Allow 24 hour before pressure testing

8. Reposition o-ring in groove in the valve base.

9. Replace dome and V-Clamp and tighten until

snug

10. Thread the pressure gauge to the top of the

dome. Do Not Use Teﬂon Tape.

11. Pressurize with pool plumbing (do not

exceed 35 psi)

12. Store the module assembly in a safe place

and install after the pool has been started

up.

* Pipes should be a minimum of 12” in length

and should insure that valve be at least 6”

above water level.

Gluing instructions

PLUMBING & CONCRETE DETAIL

Gunite or Shotcrete Process

CONCRETE:

1. Make a cutout or opening approximately 1"

deep and 1" bigger than the pipe.

2. This cutout will be ﬁlled with plaster and create

a water stop.

Verify the angle of the risers as it is

imperative that the riser angle be 90 degrees

from the ﬁnished ﬂoor angle. Check that

the system did not lose pressure prior to

shooting the pool and upon completion.

PLUMBING FOR FLOOR NOZZLES

NOTE: All risers must be 90 degrees

(perpendicular) to the ﬁnished ﬂoor

2"SCH. 40 PIPE,

15"LONG

2"ELBOW 2"PIPE

1"X 1"CUTOUT

AROUND THE

PIPE FOR WATER

CUT PIPE HERE

SOIL

CONCRETE

PRE-PLASTER DETAIL | SMOOTH BODY INSTALLATION

1. Make a cutout or opening approximately 1"

deep and 1" bigger than the pipe. This cutout

will be ﬁlled with plaster or other ﬁnish coat to

create a water stop.

2. Cut off riser pipes ﬂush with concrete

surface.

3. Remove cap. Prime the inside of the pipe.

DO NOT PRIME THE BODY.

4. Glue the body into the pipe with a regular

PVC glue.

The glue must cover the full length of the body

barrel and 3” deep inside the riser pipe. Push

the body into the pipe until the shoulder hits the

top edge of the pipe.

Let fumes vent for 30 minutes then replace all

body caps.

5. PLASTERING THE POOL

Leave all plaster caps in place for removal at

start up.

NOTE: Optional, the plaster crew may remove

the plaster caps as they ﬁnish.

NOTE: The body does not come with the

nozzle installed.

NOTICE: You can use regular PVC glue on smooth body

SOIL

CONCRETE

PRE-PLASTER DETAIL | RIBBED BODY INSTALLATION

1. Make a cutout or opening approximately 1”

deep and 1” bigger than the pipe.

This cutout will be ﬁlled with plaster or other

ﬁnish coat to create a water stop.

2. Cut off riser pipes ﬂush with concrete surface.

3. Remove cap. Prime the inside of the pipe.

DO NOT PRIME THE BODY.

DO NOT ROTATE THE BODY IN THE

PIPE.

4. Glue the body into the pipe with a HEAVY

BODY PVC SOLVENT CEMENT.

The glue must cover the full length of the body

barrel and 3” deep inside the riser pipe. Push

the body into the pipe until the shoulder hits

the top edge of the pipe.

Let fumes vent for 30 minutes then replace all

body caps.

5. PLASTERING THE POOL

Leave all plaster caps in place for removal at

start up.

NOTE: Optional, the plaster crew may remove

the plaster caps as they ﬁnish.

NOTE: The body does not come with the nozzle

installed.

NOTICE: HEAVY BODY GLUE IS REQUIRED

PARAMOUNT MODULE ALIGNMENT GUIDE

INSTALLING NOZZLE CAPS

TO FUNCTION PROPERLY IT IS IMPERATIVE THAT THE MODULE BE PLACED IN

CORRECT ORIENTATION TO THE BASE. TO ENSURE THIS IS DONE,

PLEASE FOLLOW THESE INSTRUCTIONS.

1. Look at the top of the Module - Figure 1

2. Locate the Multi port Tube Assembly - Figure

3. Look at the Base - Figure 2

4. One open port is centered between two

plugged ports - Figure 2

5. When installed, the ports centered under the

Multi port Tube Assembly (Figure 1A) on the

Module must be centered over the open ports

in the Base - Figure 2A

Figure 1

2-Port Module

Figure 2

Base

Figure 2A

Ports

Figure 1A

Multi port Tube Assembly

If the Module is placed incorrectly, the returns and nozzles in the pool will ﬁre at the

same time.

Small Nozzle Tool Part #004-552-5452-00

4. Turn cap clockwise until

it snaps into place.

1. Select nozzle size from pool

plan and using the nozzle

tool to twist on caps.

2. Place the nozzle inside

the nozzle tool to hold

it from spinning as you

twist on the cap.

3. Place the cap on the

nozzle. It will go on and

twist one way.

START-UP CLEANING NOZZLE

System Start Up

1. Before installing nozzles ﬂush all lines by:

a. Start pump, run for 10 minutes before

installing the water valve module.

b. Install the water valve module and

let valve cycle to ﬂush out any debris

remaining in each line.

2. Be sure o-ring is pushed all the way up to

top ﬂange.

3. Start with nozzle closest to the valve,

make sure the red plaster caps have been

blown out before installing the nozzles.

4. Snap the nozzle onto the nozzle tool by

twisting. Figure 3

5. Install nozzle in body by turning clockwise

one-quarter turn. Figure 4

Fig. 3

Fig. 4

Dieses Handbuch passt für folgende Modelle

Andere Paramount Fitness Beleuchtungsausrüstung Handbücher

Paramount Fitness

Paramount Fitness Paraskim V Programmierhandbuch

Paramount Fitness

Paramount Fitness MDX-R3 Programmierhandbuch

Paramount Fitness

Paramount Fitness MDX-R3 Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX-R3 Programmierhandbuch

Paramount Fitness

Paramount Fitness MDX2 retro Bedienungsanleitung

Paramount Fitness

Paramount Fitness PARASCOPE Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX DEBRIS REMOVAL SYSTEM Bedienungsanleitung

Paramount Fitness

Paramount Fitness Paraskim V Programmierhandbuch

Paramount Fitness

Paramount Fitness SDX 2 Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX-R3 Programmierhandbuch

Paramount Fitness

Paramount Fitness ECOSYSTEM Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX2 retro Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX-R3 Programmierhandbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung