Parsec Technologies BELGIAN SHEPHERD Bedienungsanleitung

Figure 1 Figure 2

BELGIAN SHEPHERD

Installation Instructions

The Belgian Shepherd PRO Series antennas are rugged,

high-performance, 5G, CAT18 (600 MHz to 6 GHz)

antennas, available with up to 4x4 MIMO LTE, up to 4x4

MIMO WiFi, CBRS, LTE LAA, and GPS/GNSS. The Belgian

Shepherd PRO Series antennas are IP67- rated antennas

and perfect for mobile and xed wireless applications.

Selecting Mounting Location

Importance of Mounting on a Flat Surface

Selecting the Mounting Option

- For best performance it is important that the antenna be mounted on a conductive panel.

- Select the mounting location such that it is at least 18 inches or as far as possible from the other roof mounted

items like antennas, light bars etc. to avoid any de-tuning or interference issues.

- Make sure there is enough clearance under the panel and there is no cross braces or double skin panel under the

mounting location.

- Measure to check for central position if applicable.

- Remove the headliner under the marked location to avoid damaging it.

A clean, at, and level surface is recommended to install the antenna to properly seal the gap between the antenna

and mounting surface. If the antenna must be mounted on a curved or a ridged surface use the appropriate Parsec

gaskets for mounting the antenna. (sold separately).

- Roof Mount (Included)

Belgian Shepherd PRO series antennas can be mounted on an

automobile roof or any at surface using the hardware provided with it.

(Figure 1)

- Magnetic Mount (Not Included)

For temporary use. Belgian Shepherd PRO series antennas can be

mounted on any ferrous metal surface using magnetic mount brackets.

(Figure 2)

PTA0341 – Gasket for mounting antennas on Ford Explorer 2020.

PTA0342 – Gasket for mounting antenna on curved surfaces (Dodge Charger, etc..).

Mounting Preparation

Step 1.

Step 2.

Step 3.

Step 4.

After selecting the location to mount the Antenna, mask the mounting location to avoid paint damage. Then mark the

hole center with ink or scribed cross hairs.

Use a center punch to make a dimple on the marked location to avoid drill bits from walking across the sheet metal.

Then use a Twist drill of diameter about 0.1” and drill a pilot hole. Then using a 1.5” diameter sheet metal hole saw, drill

the hole.

The hole saw will cut the required diameter hole with less risk of stretching and distorting the vehicle surface. Clean up

any metal shavings from the hole cutting process. (Figure 3)

Clean up any metal shavings from the hole cutting process.

FIGURE 3

Preparing the Hole

Step 3.

Step 4.

Step 5.

Step 1.

Step 2.

Lift the antenna and remove the protective backing from the underside of the antenna and place the antenna back in

the desired position. Apply downward pressure on the antenna to stick it to the panel.

To avoid the gap between the antenna and panel, it is reccomenended to use neutral cure silicon sealant around the

base of the mounting boot to fully compress the antenna to the mounting panel.

A split at washer and a split hex nut are provided in the kit for easy installation.

(Star washer is optional and not supplied.)

On the inside of the vehicle, thread the at washer over the cable, followed by star washer (if applicable) and then hex

nut. (Figure 4 & 5)

Slide the washers and nut to the threaded ange of the antenna and tighten the hex nut until antenna compresses at

with the surface of the vehicle.

(Figure 6)

Feed the coaxial cables from the antenna through the hole from the outside surface to the inside surface and thread

the entire length of the cable through the hole.

Clean debris off the vehicle surface and then mark the desired antenna orientation by placing the antenna at on the

vehicle surface.

FIGURE 5

FIGURE 6

FIGURE 4

Roof

Split Washer

Star Washer*

Split Hex Nut

Mounting the Antenna

*** For best performance avoid bending the cable under 0.5” radius. And make sure

the antenna is mounted in correct direction and tighten the mounting hardware. And

waterproof the RF connectors using electric tape or a heat shrink tube if required.

Step 1.

Step 2.

Clean the connector such that there is no dust in the

terminals.

Connect the cables from the antenna to the designated connector on the antenna as shown in the table below.

For best MIMO performance use the following in pairs:

LTE1 & LTE2

LTE3 & LTE4

WIFI 1 & WIFI 2

WIFI 3 & WIFI 4

Cable Connection Instructions

Note: SMA connectors have a maximum torque of 3-5 inch lbs.

972-804-4600

Parsec Technologies

[email protected]

Last Revised: 3.9.2021

Inhaltsverzeichnis

Andere Parsec Technologies Antenne Handbücher

Parsec Technologies

Parsec Technologies NEWFOUNDLAND L Bedienungsanleitung

Parsec Technologies

Parsec Technologies LABRADOR Bedienungsanleitung

Parsec Technologies

Parsec Technologies ST. BERNARD Bedienungsanleitung

Parsec Technologies

Parsec Technologies DOBERMAN Bedienungsanleitung

Parsec Technologies

Parsec Technologies GREAT PYRENEES Series Bedienungsanleitung

Parsec Technologies

Parsec Technologies Beagle G Bedienungsanleitung

Parsec Technologies

Parsec Technologies Bernese Mountain Dog A Bedienungsanleitung

Parsec Technologies

Parsec Technologies Beagle PRO5B2L2WG-G Bedienungsanleitung

Parsec Technologies

Parsec Technologies ROTTWEILER Bedienungsanleitung

Parsec Technologies

Parsec Technologies K9 PRO Series Bedienungsanleitung

Parsec Technologies

Parsec Technologies ST. BERNARD A Bedienungsanleitung

Parsec Technologies

Parsec Technologies GOLDEN RETRIEVER A Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung