PASCO //code.Node Holder Bedienungsanleitung
//code.Node Holder
PS-3233
Product Description
The //code.Node Holder is an accessory for the //code.Node (PS-3231). The Holder is
used to mount the //code.Node to a variety of surfaces.
12
3
What's Included
What's Required
• //code.Node (PS-3231)
//code.Node Holder with Strap
Use the strap on the Holder to mount a
//code.Node to a variety of objects.
1
Hook and Loop Strap
For attaching to the strap on the Holder
to create a longer strap.
2
Hook Fastener Strip
Attaches to the loop fastener strip on
the back of the Holder. Use the sticky
back on the strip to attach it to a
smooth surface.
3
Instruction Manual | 012-16830A
1
//code.Node Holder Features
1
2
4
3
Strap Slots
For inserting the included hook and
loop strap.
1
Fastener Hole
Use to insert a fastener (such as a
screw) for a permanent mounting
option.
2
Feet
Provides a stable base to allow the
//code.Node to stand upright.
3
Release Tab
For securing the //code.Node to the
Holder. Pull gently to release the
//code.Node from the Holder.
4
Loop Fastener Strip (not shown)
The strip is located on the back of the
Holder. Use the strip to attach the
Holder to the included hook fastener
strip.
5
//code.Node Holder | PS-3233
2
Install the //code.Node into the Holder
1. Insert the top side of the //code.Node into the Holder face up.
2. Press down the bottom side of the //code.Node until it snaps in place.
To release the //code.Node from the holder, gently pull back the release tab then pull the
//code.Node out of the Holder.
Mount the //code.Node
The //code.Node Holder provides multiple ways to mount the //code.Node.
Using the Strap
Wrap the hook and loop strap around an object. If the strap is not long enough to reach
around the object, attach the second strap to the first strap.
Using the Loop Fastener Strip
Peel off the protective film on the hook fastener strip to expose the adhesive. Press the
strip onto a smooth surface. Use the loop fastener strip on the back of the Holder to
mount the Holder to the surface.
Using the Fastener Hole
Remove the strap from the Holder. Insert a screw through the fastener hole to mount the
Holder.
Instruction Manual | 012-16830A
3
Appendix
Technical Support
Contact PASCO Technical Support for assistance with this or any other PASCO product.
Address PASCO scientific
10101 Foothills Blvd.
Roseville, CA 95747-7100
Phone 1-800-772-8700 (USA)
1-916-462-8384 (International)
Chat www.pasco.com
email [email protected]
Warranty, Copyright, and Trademarks
Limited Warranty
For a description of the product warranty, see the Warranty and Returns page at www.pasco.com/legal.
Copyright
This document is copyrighted with all rights reserved. Permission is granted to non-profit educational
institutions for reproduction of any part of this manual, providing the reproductions are used only in their
laboratories and classrooms, and are not sold for profit. Reproduction under any other circumstances, without
the written consent of PASCO scientific, is prohibited.
Trademarks
PASCO and PASCO scientific are trademarks or registered trademarks of PASCO scientific, in the United
States and/or in other countries. All other brands, products, or service names are or may be trademarks or
service marks of, and are used to identify, products or services of, their respective owners. For more
information visit www.pasco.com/legal.
CE Statement
This device has been tested and found to comply with the essential requirements and other relevant provisions
of the applicable EU Directives.
//code.Node Holder | PS-3233
4
Dieses Handbuch passt für folgende Modelle
1
Andere PASCO TV-Halterung Handbücher
