Patton electronics 1094 Bedienungsanleitung

USER

MANUAL

MODEL 1094

KiloModem-768

TM High

Speed Baseband Modem

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M1094-C

Doc# 032031UC

R evised 04/13/99

CERTIFIED

An ISO-9001

Certified Company

1 2

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1094 components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials,

and does not cover customer damage, abuse or unauthorized modifi-

cation. If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or consequen-

tial damages arising from the use of or inability to use this product.

Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1094 generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and tele-

vision reception. The Model 1094 has been tested and found to com-

ply with the limits for a Class A computing device in accordance with

the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If the Model 1094 does

cause interference to radio or television reception, which can be deter-

mined by removing power from the unit, the user is encouraged to try

to correct the interference by one or more of the following measures:

moving the computing equipment away from the receiver, re-orienting

the receiving antenna and/or plugging the receiving equipment into a

different AC outlet (such that the computing equipment and receiver

are on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Technical

Support.

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight pre-

paid and insured to Patton Electronics. All returns must have a Return

Materials Authorization number on the outside of the shipping contain-

er. This number may be obtained from Patton Electronics Technical

Service at:

TEL: (301) 975-1007

Email: [email protected].

www: http://www.patton.com

Patton Electronics’ technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1094. Technical Support hours: 8AM to 5PM EST, Monday

through Friday.

NOTE: Packages received without an RMA number will not be

accepted.

3 4

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is warrant-

ed for OneYear parts and labor. If any questions or problems arise

during installation or use of this product, please do not hesitate to con-

tact Patton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• Synchronous data rates of 384 and 768 kbps

• Frequency Shift Key (FSK) modulation

• Full or half duplex operation over two twisted pair (4-wire)

• Point-to-point distances up to 4.9 miles (19 AWG @ 384 kbps)

• V.54 compliant local and remote loopback tests (DTE or

front panel activated)

• V.52 compliant Bit Error Rate (BER) test pattern generator

• Replaceable DTE-DCE QuickConnect™ interface modules

• Internal, external or receive recovered clocking options

• Automatic equalization

• Made in the U.S.A.

2.2 DESCRIPTION

The Patton Model 1094 Synchronous Short Range Modem

is designed for point-to-point, high speed communication over 4-wires

(two twisted pair). Supporting switch-selectable data rates of 384 and

768 kbps, the Model 1094 is perfect for connecting two bridge/routers,

or for similar campus applications at distances up to 4.9 miles (7.9 km).

The Model 1094 incorporates built-in V.54 loopback tests, a V.52 BERT

pattern generator and seven front panel LED indicators. Data integrity

is enhanced by automatic equalization and gain control. The Model

1094 also incorporates transformer isolation and surge protection to

guard data and connected equipment against the hazards of ground

loops and transient surges. Clocking options include internal, external

and receive recover clock.

The Model 1094 features replaceable DCE-DTE QuickConnect™

interface modules. Several different modules are available (call Patton

Sales for details). Line connection is made by RJ-45 jack. Internal AC

power supply options include 120 or 230VAC (switchable), 85-256VAC

(universal) or 48VDC.

3.0 CONFIGURATION

The Model 1094 is equipped with one set of eight DIP switches,

and one set of four DIP switches (all externally accessible). These DIP

switches allow configuration of clock source, carrier control, loopback

tests and data rate.This section describes switch locations and

explains all possible configurations.

3.1 EXTERNAL DIP SWITCH SETTINGS

The Model 1094’s DIP switches are located on the underside of

the unit (see Figure 1, below). Figure 2 shows the orientation of the

switch set. All possible settings for the Model 1094’s DIP switches are

presented in the summary table and descriptions on the following

pages.

Figure 2. Close Up of Configuration Switches

1234

12345678

1234

Figure 1. Underside of Model 1094 Showing External DIP Switch Locations

FRONT

REAR

S1 S2

OFF

5 6

3.1.1 Switch Set S1

The configuration switches on S1 set clock source, RTS/CTS

delay, carrier control, loopback tests. The default settings are summa-

rized in the table above.

Switches S1-1 and S1-2: Clock Source

Switches S1-1 and S1-2 are set in combination to determine the

source of timing for the Model 1094.

S1-1 S1-2 Setting

On On Internal

On Off Receive recover

Off On External transmit clock

Off Off Not a valid setting

Switch S1-3: RTS/CTS Delay

Switch S1-3 is used in combination to determine the amount of

delay between the time RTS is activated and the 1094 activates the

CTS.

S1-3 Function

On Short delay (1-4 ms)

Off Long delay (8-20 ms)

Switch S1-4: LDL Control

Switch S1-4 determines whether the frontt panel switch can acti-

vate a Local Digital Loopback (LDL) diagnostic test.

S1-4 Function

On LDL Control Enabled

Off LDL Control Disabled

Switch S1-5: Carrier Control

The setting for switch S1-5 determines whether the carrier is “con-

stantly on” or “controlled by RTS”. This setting allows for operation in

switched carrier or hardware handshaking applications.

S1-5 Setting

On Controlled by RTS

Off Constantly ON

Switch S1-6: DTE Control of RDL

The setting for switch S1-6 determines whether DTE control of

remote-digital loopback test is enabled or disabled. If DTE control is

disabled, the RDL test can only be initiated by the front panel switch.

S1-6 Setting

On DTE control enabled

Off DTE control disabled

Switch S1-7: DTE Control of LAL

The setting for switch S1-7 determines whether DTE control of

local analog loopback test is enabled or disabled. If DTE control is dis-

abled, the LAL test can only be initiated by the front panel switch.

S1-7 Setting

On DTE control enabled

Off DTE control disabled

S1 SUMMARY TABLE

Position Function Factory Default

S1-1 Clock Source* On

S1-2 Clock Source* On

S1-3 RTS/CTS Delay On Short Delay

S1-4 LDL Off Disabled

S1-5 Carrier Control Off Constant

S1-6 DTE Control of RDL Off Disabled

S1-7 DTE Control of LAL Off Disabled

S1-8 V.54 Enable/Disable Off Enabled

*See Note in SWITCH SET S1 (Below) for X.21 Clock Sources

}

Internal

NOTE: When an X.21 QuickConnect™ module is installed in

one or both base units, one base unit

must

be configured for

receive recover clock source. The particular application will

dictate which unit must be configured for receive recover clock

source.

7 8

Switch S1-8: V.54 Enable / Disable

The setting for switch S1-8 determines whether the Model 1094

will respond when it receives the V.54 sequence. If you suspect the

Model 1094 may be getting tricked into the loopback test by false

detection of user data, you can try setting this to “Disable.”

S1-8 Setting

On Disabled

Off Enabled

3.1.2 Switch Set S2

The settings for DIP switches S2-1 through S2-4 determine the

synchronous data rate of the Model 1094. All possible settings (includ-

ing the default) are shown below:

S2-1 S2-2 S2-3 S2-4 Setting

Off On On On 384 kbps

On Off Off Off 768 kbps (default)

4.0 INSTALLATION

Once the Model 1094 is properly configured, it is ready to connect

to the twisted pair interface, to the serial port, and to the power source.

This section tells you how to make these connections.

4.1 CONNECTION TO THE TWISTED PAIR INTERFACE

The Model 1094 supports communication between two terminal

devices at distances to 4.9 miles (7.9 km) and data rates to 768 kbps.

There are two essential requirements for installing the Model 1094:

1. These units work in pairs. Therefore, you must have one

Model 1094 (or a compatible model) at each end of a two

twisted pair interface.

2. To function properly, the Model 1094 needs two twisted pairs

of metallic wire. These twisted pairs must be

unconditioned, dry, metallic wire, between 19 and 26 AWG

(.4 mm and .9 mm, inversely) (the higher AWG gauges may

limit distance somewhat). Standard dial-equalization

equipment, or standard, flat modular telephone type cable, are

not acceptable.

4.1.1 TWISTED PAIR CONNECTION USING RJ-45

The Model 1094 uses a modular RJ-45 jack for twisted pair line

connection. The signal/pin relationships are shown below:

RJ-45 SIGNAL

1..........................XMT+

2..........................XMT-

3..........................N/C

4..........................GND*

5..........................GND*

6..........................N/C

7..........................RCV+

8..........................RCV-

*Connection to ground is optional

9 10

When connecting two Model 1094’s, it is necessary to use a

crossover cable. The diagram below shows how a crossover cable

should be constructed.

RJ-45 Cable (4-Wire)

SIGNAL PIN# PIN# SIGNAL

XMT+ 1-----------------------8 RCV-

XMT- 2-----------------------7 RCV+

GND* 4-----------------------5 GND*

GND* 5-----------------------4 GND*

RCV+ 7-----------------------2 XMT-

RCV- 8-----------------------1 XMT+

*Connection to ground is optional

4.2 CONNECTION TO THE SERIAL PORT

The serial port interface on the Model 1094 uses interchangeable

Quick Connect Modules. Each Quick Connect Module has a 50-pin

card edge connector on one side and a serial port interface on the

other. Figure 3 (below) shows how a Quick Connect™ Module plugs

into the back of the Model 1094.

4.2.1 CHANGING QUICKCONNECT™ MODULES

When you purchase a particular version of the Model 1094, it

should be shipped to you with the appropriate QuickConnect™

Module already installed. If you need to install a different

QuickConnect™ Module, follow these steps.

Removing the Existing QuickConnect™ Module

1. Turn the power switch off. Leave the power cord plugged into a

grounded outlet to keep the unit grounded.

2. Loosen the two thumbscrews on the module by turning them

counterclockwise.

3. Grasp the two thumbscrews and gently pull the module from

the unit. Apply equal force to the thumbscrews to keep the

module straight during the removal process.

Installing the New QuickConnect™ Module

1. Make sure the power switch is off. Leave the power cord

plugged into a grounded outlet to keep the unit grounded.

2. Hold the module with the faceplate toward you and align the

module with the guide slots in the rear panel of the Model

1094.

3. While keeping the module’s faceplate parallel with the Model

1094 rear panel, slide the module straight in–so that the card

edge contacts line up with the socket inside the chassis.

4. With the card edge contacts aligned with the socket, firmly seat

the module by using your thumbs to apply pressure directly to

the right and left edges of the module faceplate. Applying mod-

erate and

even

pressure should be sufficient to seat the mod-

ule. You should hear it snap into place.

5. To secure the module in place, push the thumbscrews into the

chassis and turn the screws clockwise to tighten.

0 OFF

1 ON

Line

Interface Port

Figure 3. Installation of Model 1094 Plug-in Serial Interface Module

NOTE:The card edge connector should meet the socket when

it is almost all the way into the chassis. If you encounter a lot of

resistance, remove the module and repeat Steps 2 and 3.

11 12

4.2.2 CONNECTION TO A “DTE” DEVICE

The serial port on most QuickConnect™ interface modules (all

except the X.21 module) is hard-wired as a DCE. Therefore these

modules “want” to plug into a DTE such as a terminal, PC or host.

When making the connection to your DTE device, use a straight

through cable of the shortest possible length—we recommend 6 feet

or less. When purchasing or constructing an interface cable, please

refer to the pin diagrams in Appendix D as a guide.

4.2.3 CONNECTION TO A “DCE” DEVICE

If the Model 1094’s QuickConnect™ interface module is hard-

wired as a DCE (all except the X.21 module), you must use a

null

modem

cable when connecting to a printer, modem, multiplexer or

other DCE device. This cable should be of the shortest possible

length—we recommend 6 feet or less. When purchasing or construct-

ing a null modem interface cable, use the pin diagrams in Appendix D

as a guide.

4.2.4 RECONFIGURING THE X.21 QUICKCONNECT™ MODULE

The serial port on the X.21 QuickConnect™ Module is default

wired as a DCE, but may be switched to a DTE. This is done by

reversing the orientation of the DCE/DTE strap, as described below:

To reverse DCE/DTE orientation, remove the module according to

the instructions in Section 4.2.1. The DCE/DTE strap is located on the

bottom side of the module’s PC board. The arrows on the top of the

strap indicate the configuration of the X.21 port (for example, if the

DCE arrows are pointing toward the DB-15 connector, the X.21 port is

wired as a DCE). Reverse the DCE/DTE orientation by pulling the

strap out of its socket, rotating it 180º, then plugging the strap back into

the socket. You will see that the DCE/DTE arrows now point in the

opposite directions, showing the new configuration of the X.21 port.

Reinstall the module according to the instructions in Section 4.2.1.

4.3 CONNECTION TO THE POWER SOURCE

The Model 1094 is available with three power supply options:

The Standard power supply option (Model 1094 or 1094-230) is

factory configured for either 115 or 230 VAC, depending on how the

product is ordered, and is available with a variety of domestic and inter-

national power cords (see Appendix C).

The Universal Interface power supply option (Model 1094-UI)

operates in environments ranging from 85 to 265 VAC, with no re-con-

figuration necessary (see Appendix C for available domestic and inter-

national power cords).

The DC power supply option (Model 1094-DC) operates in 48

VDC environments and is equipped with a 3-pin terminal block with

spring-type contacts (please refer to the Model 1094 Service Manual

for wiring instructions).

4.3.1 AC POWER CONNECTION

The two AC power supply options–Standard and Universal–are

equipped with a male IEC-320 power connection. A domestic (US)

power supply cord is supplied with the unit at no extra charge. To con-

nect the standard or universal power supply, follow these steps:

1. Attach the power cord (supplied) to the shrouded male IEC-

320 connector on the rear of the Model 1094.

2. Plug the power cord into a nearby AC power outlet.

3. Turn the rear power switch ON.

Note: Pin-out requirements for null modem applications vary

widely between manufacturers. If you have any questions about a

specific application, contact PattonTechnical Support:

TEL: (301) 975-1007

Email: [email protected].

www: http://www.patton.com

WARNING! There are no user-serviceable parts in the power

supply section of the Model 1094. Voltage setting changes and

fuse replacement should only be performed by qualified serv-

ice personnel. Any questions may be answered by contacting

Patton Electronics Technical support at (301) 975-1007; sup-

[email protected]; or http://www.patton.com.

13 14

5.0 OPERATION

Once the Model 1094 is properly configured and installed, it

should operate transparently. This sections describes power-up, read-

ing the LED status monitors, and using the built-in loopback test

modes.

5.1 POWER-UP

Before applying power to the Model 1094, first be sure that you

have read Section 4.3, and that the your power source matches the

power rating shown on the bottom label of the Model 1094.

Failure to

do so could result in damage to the unit and connected

equipment, and may constitute a fire hazard.

If your Model

1094 is AC powered, plug the AC power cord into both the Model 1094

and the AC outlet. Then power-up the unit using the rear power switch.

If your Model 1094 is DC powered, and has been connected to the DC

power source according to the instructions in Section 4.3, turn on the

DC power supply and then power-up the unit using the rear power

switch.

5.2 LED STATUS MONITORS

The Model 1094 features seven front panel LEDs that monitor

transmit data, receive data, request to send, carrier detect, data termi-

nal ready, test modes and error conditions. Figure 4 (below) shows the

front panel location of each LED. Following Figure 6 is a description of

each LED’s function.

TD and RD Will glow red to indicate an idle condition of Binary

1 data on the respective terminal interface

signals. Green indicates Binary“0 data.

RTS Will glow green to indicate that the Request to

Send signal from the terminal is active.

CD Will glow red if no carrier signal is being received

from the remote modem. Green indicates that the

remote modem’s carrier is being received.

DTR Will glow green to indicate that the Data Terminal

Ready signal from the terminal is active.

ER Will glow red to indicate the likelihood of a Bit

Error in the received signal. During the 511 or

511/E test, ER will flash to indicate that the Test

Pattern Detector has detected a bit error.

TM Will glow green to indicate that the Model 1094

has been placed in Test Mode. The unit can be

placed in test mode by the local user or by the

remote user.

5.3 DIAGNOSTICS

The Model 1094 is equipped with three sets of diagnostics to eval-

uate the condition of the local and remote units, as well as the twisted

pair link between them: local analog loopback (LAL) and remote digital

loopback (RDL) according to the CCITT V.54 Standard, and bit error

rate BER test according to the CCITT V.52 Standard.

5.3.1 LOCAL ANALOG LOOPBACK (LAL)

The Local Analog Loopback (LAL) test checks the operation of the

local Model 1094. Any data sent to the local Model 1094 in this test

mode will be echoed (returned) back to the user device. For example,

characters typed on the keyboard of a terminal will appear on the ter-

minal screen (see Figure 5, below).

To perform an Analog Loopback test, follow these steps:

A. Activate Local Analog Loopback. This may be done in one of

two ways: First, by moving the front panel toggle switch UP to

Local. Second, by raising signal LOCAL LOOPBACK on the

terminal interface (for pin numbers, see Appendix D). Once

LAL is activated, the Model 1094 transmit output is connected

to its own receiver. The TM LED should be lit.

(continued)

Model 1090

KiloModem PS

High Speed Sync. Short Range Modem

RDTD RTS CD DTR ER TM Test Modes

Local -

Normal -

Remote -

- 511E

- Normal

- 511

Figure 4. Model 1094 Front Panel

1090

Figure 5. Local Analog Loop

Local 1094

15 16

B. Verify that the data terminal equipment is operating properly

and can be used for a test. If a fault is indicated, call a

technician or replace the unit.

C. Perform a BER (bit error rate) test on each unit using a

separate BER tester. If the BER test equipment indicates no

faults but the data terminal indicates a fault, follow the

manufacturer's checkout procedures for the data terminal.

Also, check the interface cable between the terminal and the

Model 1094.

5.3.2 REMOTE DIGITAL LOOPBACK (RDL)

The Remote Digital Loopback (RDL) test checks the performance

of both the local and remote Model 1094',

and

the communication link

between them. Any characters sent to the remote Model 1094 in this

test mode will be returned back to the originating device (see Figure 6,

below).

To perform an RDL test, follow these steps:

A. Activate RDL. This may be done in one of two ways: First, by

moving the front panel toggle switch DOWN to “Remote”. Or,

second, by raising the REMOTE LOOPBACK signal on the

terminal interface (for pin numbers, see Appendix D).

B. Perform a BER (bit error rate) test on the system, using BER

testers on both ends.

C. If the BER test equipment indicates a fault and the Local

Analog Loopback test was successful for both Model 1094s,

you may have a problem with the line between the Model

1094s. You should inspect the line for proper connections.

5.3.3 LOCAL DIGITAL LOOPBACK (LDL)

The Local Digital Loopback (LDL) test checks the local and remote

1094s and all communication paths. In LDL, the TX/RX circuit of the

local 1094 closes, thereby allowing characters sent from BOTH the

local terminal and remote terminal to loop back (echo) to themselves

(See Figure 7, below). To accurately perform LDL diagnostics, techni-

cians must send characters (or BER diagnostics) from each end. To

perform a LDL, follow the instructions below:

A. On the bottom of the unit, turn S1-4 to the ON position.

B. Enable LDL by moving the front panel toggle switch up to

“Local”, Or, by raising the signal LL on the terminal

interface(for pin numbers, see Appendix D).

C. Perform a BER (bit error rate) test on the system, using BER

testers on both ends.

D. If the BER test equipment indicates a fault and the Local

Analog Loopback test was successful for both Model 1094s,

you may have a problem with the line between the Model

1094s. You should inspect the line for proper connections.

Figure 7. Local Digital Loop

Figure 6. Remote Digital Loop

Local 1094 Remote 1094

NOTE: LDL will only work when S1-4 is ON.

17 18

5.3.4 V.52 BER TEST GENERATOR

The Model 1094 has a built-in test pattern generator and detector.

It can be invoked at both ends of a link simultaneously or it can be

used with the Local Analog or Remote Digital Loopbacks. The follow-

ing example requires two operators: one to initiate and monitor the test

at the local Model 1094, and one at the remote Model 1094. To use

the V.52 BER test by itself, both operators should simultaneously follow

these steps.

1. Locate the 511/511E toggle switch on the front panel of the

Model 1094 and move it DOWN. This activates the V.52 BER

test mode and transmits a 511 pseudorandom test pattern to

the other unit. If any errors are received, the receiving Model

1094’s red ER LED will blink sporadically.

2. If the test indicates no errors are present, move the V.52

toggle switch UP, activating the 511/E test. The 511/E test

transmits the 511 pseudorandom test pattern and injects

intentional errors about once per second. If the test is work-

ing properly, the receiving Model 1094’s red ER LED will blink

regularly

A successful 511/E test will confirm that the link is in place,

and that the Model 1094 built-in 511 generator and detector

are working properly.

3. This test can be done by one operator by first activating the

local analog loop or remote digital loop.

APPENDIX A

PATTON ELECTRONICS MODEL 1094

SPECIFICATIONS

Transmission Format: Synchronous

Transmission Line: Unconditioned twisted pair 19 - 26 AWG

Clocking: Internal, external or receive loopback

Distance: Up to 4.9 miles (7.9 km)

(19 AWG @ 384 kbps)

Data Rates: 384 and 768 kbps (switch selectable)

Carrier Control: Constantly on or Controlled by RTS

RTS/CTS Delay: No delay, short delay (1 - 4 ms),

long delay (8 - 20 ms).

Diagnostics: V.52 compliant bit error rate pattern

(511/511E pattern) generator and detector

with error injection mode;V.54

compliant—local analog loopback and

remote digital loopback, activated by front

panel switch or via serial interface

LED Status: TD, RD, RTS, CD, DTR, ER and TM

Indicators: (test mode)

Isolation: Minimum 3000V RMS via transformers

Surge Protection: Immune to IEC-801-5 Level 2, 1kV

DCE/DTE Interface: Field-replaceable Quick ConnectTM

modules.

Twisted Pair Interface: 8-position modular jack (RJ-45)

Power: 115/230 VAC (switch selectable), 50/60 Hz;

85 - 256 VAC, 50/60 Hz (universal input

option); 48 VDC (option). 5 watts.

Temperature Range: 0-50°C (32-122°F)

Altitude: 0-15,000 feet

Humidity: 5 to 95% non-condensing

Dimensions: 7.3” x 6.6” x 1.62”

(185mm x 168mm x 41mm)

Weight: 2.02 lbs. 1.0 Kg

NOTE: For this test to function, the 511 switch on both Model

1094’s must be on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Modem Handbücher

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics 1186 Bedienungsanleitung

Patton electronics

Patton electronics 1070 Bedienungsanleitung

Patton electronics

Patton electronics 3010 Bedienungsanleitung

Patton electronics

Patton electronics 1089/C Bedienungsanleitung

Patton electronics

Patton electronics NetLink 1082 Bedienungsanleitung

Patton electronics

Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

Patton electronics

Patton electronics 1193 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 1052 Series Bedienungsanleitung

Patton electronics

Patton electronics 1080A Bedienungsanleitung

Patton electronics

Patton electronics 1009 Bedienungsanleitung

Patton electronics

Patton electronics 1203 Bedienungsanleitung

Patton electronics

Patton electronics 1226 Bedienungsanleitung

Patton electronics

Patton electronics 1180/35 Bedienungsanleitung

Patton electronics

Patton electronics 1004 Bedienungsanleitung

Patton electronics

Patton electronics 1140RC Bedienungsanleitung

Patton electronics

Patton electronics Model 1065 Bedienungsanleitung

Patton electronics

Patton electronics 1000 Bedienungsanleitung

Patton electronics

Patton electronics 1004ABRC Bedienungsanleitung

Patton electronics

Patton electronics 1205P Bedienungsanleitung

Patton electronics

Patton electronics 2703RC Bedienungsanleitung

Patton electronics

Patton electronics 1140A Bedienungsanleitung

Patton electronics

Patton electronics 1082/F Bedienungsanleitung

Patton electronics

Patton electronics 1060 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung