Patton electronics 2190 Bedienungsanleitung

USER

MANUAL

MODEL 2190

V.90 Analog Modem

Part# 07M2190-A

Doc# 091011UA

Revised 01/29/99

SALES OFFICE

(301)975-1000

TECHNICAL SUPPORT

(301)975-1007

http://www.patton.com

CERTIFIED

An ISO-9001

Certified Company

TABLE OF CONTENTS

Section Page

1.0 Warranty Information.............................................................2

1.1 Radio and TV Interference

1.2. CE Notice

1.3 FCC Information

1.4 Service

2.0 General Information...............................................................4

2.1 Features

2.2 Package Contents

3.0 Installation .............................................................................5

3.1 Connecting to the Serial Port

3.2 Connecting to the Phone Lines

3.3 Connecting to the Microphone

3.4 Connecting to the Speaker

3.5 Connecting Power

3.6 Power

3.7 Modem Driver

4.0 Configuration ..........................................................................6

4.1 Command Guidelines

4.2 AT Commands

4.3 Dial Codes

4.4 Sub Parameter Definitions

4.5 Fax Commands

4.6 Voice Commands

4.7 Registers

4.7.1 Commands to Change or Read Registers

4.7.2 Register Descriptions

5.0 Operation.............................................................................21

5.1 Led Character Indicators

Appendix A - Specifications........................................................22

Appendix B - Result Codes ........................................................23

Appendix C- RS-232 Pin Assignments.......................................25

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 2190 components to be

free from defects, and will—at our option—repair or replace the prod-

uct should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials,

and does not cover customer damage, abuse or unauthorized modifi-

cation. If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or consequen-

tial damages arising from the use of or inability to use this product.

Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall

be deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 2190 generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and tele-

vision reception. The Model 2190 has been tested and found to com-

ply with the limits for a Class A computing device in accordance with

the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If the Model 2190 does

cause interference to radio or television reception, which can be deter-

mined by disconnecting the unit, the user is encouraged to try to cor-

rect the interference by one or more of the following measures: mov-

ing the computing equipment away from the receiver, re-orienting the

receiving antenna and/or plugging the receiving equipment into a dif-

ferent AC outlet (such that the computing equipment and receiver are

on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the European Union

(EU). A Certificate of Compliance is available by contacting Technical

Support.

1.3 FCC INFORMATION

The Model 2190 has been tested and registered in compliance

with the specifications in Part 68 of the FCC rules. A label on the

equipment bears the FCC registration number. You may be requested

to provide this information to your telephone company.

Your telephone company may make changes in its facilities, equip-

ment, operations or procedures that could affect the proper operation

of the Model 2190. If this happens, the telephone company should

give you advance notice to prevent the interruption of your service.

The telephone company may decide to temporarily discontinue

your service if they believe your Model 2190 may cause harm to the

telephone network. Whenever possible, they will contact you in

advance. If you elect to do so, you have the right to file a complaint

with the FCC.

If you have any trouble operating the Model 2190, please contact

Patton Technical Support at (301) 975-1000. The telephone company

may ask you to disconnect the equipment from the telephone network

until the problem has been corrected or until you are certain that the

Model 2190 is not malfunctioning.

1.4 SERVICE

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at:

tel: (301)975-1007

email: [email protected]

www: http://www.patton.com

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 2190. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is warrant-

ed for OneYear parts and labor. If any questions or problems arise

during installation or use of this product, please do not hesitate to con-

tact Patton Electronics Technical Support at (301) 975-1000.

2.1 FEATURES

• Data modem

-- ITU-T V.90 and K56flex (56Kbps) V.34 (33.6kbps), V.32bis, V.32,

V.22bis, V.22, V.23, and V.21; Bell 212A and 103.

-- V.42 LAPM, MNP2-4, and MNP 10 error correction.

-- V.42bis and MNP5 data compression

-- MNP 10ECTM enhanced cellular performance.

• Fax modem send and receive rates up to 14400 bps.

-- ITU-T V.17, V.29, V.27 ter, and V.21 channel 2.

• V.80 synchronous access modes supports host-based communica-

tion protocols.

• Voice/TAM mode (V, SP, and SVD models)

• Full-duplex speakerphone (FDSP) mode (SP and SVD models)

• Compatible with AT command sets.

• NVRAM directory and stored profiles.

• Flow control and speed buffering.

• Automatic format/speed sensing.

2.2 PACKAGE CONTENTS

Carefully unpack the Model 2190 package that you have received.

The following is a checklist of the package:

• One Modem

• One RJ-11 telephone cable

• One user’s manual

• Communication Software

• One AC adapter

• One RS-232 cable

3.0 INSTALLATION

The Model 2190 is equipped with one RS-232 Serial Port, two

RJ-11 connectors, 2 jack hook-ups (1 microphone, 1 speakerphone), 1

AC power source and a power switch. Figure1 below, shows the rear

panel of the Model 2190 and the location of these connectors.

Following figure 1 are sections describing proper installation of each

connector.

Figure 1. Model 2190 Rear Panel Connectors

3.1 CONNECTING TOTHE SERIAL PORT

The serial port on the Model 2190 is a RS-232 port. Use the sup-

plied cable to connect to the modem, the computer, or terminal.

3.2 CONNECTING TO THE PHONE LINES

On the Model 2190 there are two phone lines (jacks).The “Line”

jack is for the user to connect to the public telephone line.

The “phone” jack is for the user to connect to the telephone set.

You can use the telephone set, when the modem is not connected to

another modem.

3.3 CONNECTING TO THE MICROPHONE (MIC)

The external microphone (MIC) jack is valid only when the voice

option is selected.

3.4 CONNECTING TO THE SPEAKER (SPKR)

The External speaker (SPKR) jack.

3.5 CONNECTING POWER

The power source input. Put the other end into the wall outlet of

the AC power source.

3.6 POWER

Power Switch.

3.7 MODEM DRIVER

If it is required to install the Modem, use the supplied modem driv-

er disk.

4.0 CONFIGURATION

Before attempting to configure or operate the Model 2190, it is

important to know how the unit will handle command entry.This section

provides command guidelines, AT command set, dial codes, sub para-

meter definitions, fax commands, and voice commands.

4.1 COMMAND GUIDELINES

• All commands must be preceded by "AT" (ATtention code) except

for the “A/” command and "+++" escape command.

• AT commands are not case sensitive and can be entered in lower

case or uppercase characters.

• AT commands cannot be deleted by the backspace key or by the

delete key.

• The Attention Code is used by the modem to determine the speed

and data format of the in coming data from the DTE.

• More than one command can be entered in one command line

and may be separated by space for readability.

• The command line can NOT exceed 40 characters excluding the

attention code and must be ended by the ASCII character speci-

fied by S register 3.

• The default of the S register 3 is the decimal 13 -- "Carriage

Return"

• A line without carriage return will be ignored.

• Commands following the AT are processed after receiving the

"Carriage Return" character, and the space added for readability

will be ignored.

• Any parameters following the AT command that were ignored will

be treated as equal to 0.

Power Power Serial Port MIC. SPK. Phone Line

5 6

4.2 AT COMMANDS

Refer to the following AT Command Set Chart below.This chart

identifies the command function and describes the elements of the

command.

AT Command Sets

AT Command Sets (continued)

ATB0

ATB1

ATE0

ATE1

ATH0

ATH1

Answer Command

Forces the modem to go off-hook in answer mode

without waiting for a ring.

Repeat Last Commannd

Repeat the last command line it executed. Not

preceded with AT nor followed by pressing the

[Enter] key.

Select ITU-T/BELL Mode

Selects ITU-T operation at 300bps or 1200bps during

Call Establishment . (Default)

Selects BELL operation at 300bps or 1200bps during

Call Establishment.

This command directs the modem to go on-line, dial

according to the string entered and attempt to establish

a connection.

Echo Command

Disables command echo

Enables command echo (Default)

Hang Up the Telephone Line

The modem will release the line if the modem is

currently on-line, and will terminate any test (AT&T) that

is in progress. (Default)

If on-hook, the modem will go off-hook and enter

command mode.

Command

Description

ATI0

ATI1

ATI2

ATI3

ATI5

ATI6

ATL0

ATL1

ATL2

ATL3

ATM0

ATM1

ATM2

ATM3

ATN0

ATN1

ATO0

ATO1

Identification Command

Reports product code "56000".

Calulates the ROM checksum and reports the least

significant byte of the checksum in decimal.

Calculated the ROM checksum and compares it with

the prestored checksum.

Reports firmware revision (F), basic model (e.g., V34),

application code (A), and interface type code (I)

typically in the form VF,FFF-V34_A1.

Reports Country Code parameter.

Reports modem data pump model and internal code

revision.

Speaker Volume Control

Low speaker volume

Low speaker volume (Default)

Medium speaker volume

Higher speaker volume

Speaker Control

Speaker is always off.

Speaker is on during call establishment, but off when

receiving carrier. (Default)

Speaker is always on.

Speaker is off when receiving carrier and during dialing,

but on during answering.

Set Multi- or Fix- Mode Handshake

Automode detection is disabled.

Automode detection is enabled. (Default)

Return to On-Line Mode

Enters on-line data mode without a retrain. (Default)

Enters on-line data mode with a retrain before returning

to on-line data mode.

Sr=n

ATQ0

ATQ1

ATSr=n

ATS?

Set Pulse Dial

This command forces pulse dialing until the next T dial

modifier or T command is received.

Quiet Results Code Control

Enables result codes to the DTE. (Default)

Disables result codes to theDTE.

Read / Write S-Register

Sets S-Register "r" to the value n.

Reports the value of S-Register r.

Command

Description

AT Command Sets (continued) AT Command Sets (continued)

ATV0

ATV1

Set Tone Dial

This command forces DTMF dialing until the next P dial

modifier or P command is received.

Result Code From

Enables short-form (terse) result code.

Enables long-form (verbose) result code (default)

&Cn

ATW0

ATW1

ATW2

ATX0

ATX1

ATX2

ATX3

ATX4

ATY0

ATY1

ATZ0

ATZ1

AT&C0

AT&C1

Connect Message Control

Upon connection, the modem only reports the DTE

speed (e.g., CONNECT 19200). (Default)

Upon connection, the modem reports the line speed,

the error correction protocol, and the DTE speed,

respectively.

Upon connection, the modem reports the DCE speed

(e.g., CONNECT 14400).

Extended Result Codes

The modem ignores dialtone and busy tone when

dialing. Sends standard result codes when a

connection is completed regardless of connection

speed.

The modem ignores dialtone and busy tone. Sends

extended result codes when a connection is mode.

The mode ignores busy tone. Sends "NO DIALTONE" if

no dialtone is detected in 5 seconds of a dial attempt.

Sends extended result codes when a connection is

made.

The mode ignores dial tone. Sends "BUSY" if busy tone

is detected. Sends extended result codes when a

connection is made.

The modem sends "NO DIALTONE" if no dialtone is

detected in 5 seconds of a dial attempt. Sends "BUSY"

if busy tone is detected. Sends extended result codes

when a connection is made, (default)

Long Space Disconnect

Disables long space disconnect. (Default)

Enables long space disconnect.

Soft Reset and Restore Profile

Soft reset and restore profile 0.

Soft reset and restore stored profile 1.

DCD Option

DCD remains ON at all times.

DCD follows the state of the carrier. (Default)

Command

Description

&Dn

&Fn

&Gn

AT&D0

AT&D1

AT&D2

AT&D3

AT&F0

AT&F1

AT&G0

AT&G1

AT&G2

DTR Option

Assumes DTR ON.

Enters command mode on detecting ON-to-OFF

transition of DTR.

Goes ON-HOOK on detecting ON-to-OFF transition of

DTR. (Default)

Resets the modem on detecting ON-to-OFF transition of

DTR.

Restore Factory Configuration (Profile)

Restore factory configuration 0.

Restore factory configuration 1.

Select Guard Tone

Disables guard tone (Default)

Disables guard tone

Selects 1800 Hz guard tone

&Kn

AT&K0

AT&K3

AT&K4

AT&K5

AT&K6

Flow Control

Disables flow control.

Enables RTS/CTS flow control. (Default)

Enables XON/XOFF flow control.

Enables transparent XON/XOFF flow control.

Enables both RTS/CTS and XON/XOFF flow control.

&Pn

AT&P0

AT&P1

AT&P2

AT&P3

Select Pulse Dial Make/Break Ratio

Selects 39%-61% Make/Break ratio at 10 pulses per

second. (Default)

Selects 33%-67% Make/Break ratio at 10 pulses per

second.

Selects 39%-61% Make/Break ratio at 20 pulses per

second.

Selects 33%-67% Make/Break ratio at 20 pulses per

second.

&Qn

&Sn

AT&Q0

AT&Q5

AT&Q6

AT&S0

AT&S1

Select Sync/Async Mode

Selects direct asynchronous operation.

The modem will try to negotiate an error-corrected link.

(Default)

Selects asynchronous operation in normal mode.

Serial Port DSR Control Command

DSR will remains ON at all time (Default)

DSR will become active after answer tone has been

detected and inactive after the carrier has been lost.

Command

Description

910

AT Command Sets (continued)

&Tn

&V1

&Wn

&Yn

AT&T0

AT&T1

AT&T3

AT&T4

AT&T5

AT&T6

AT&T7

AT&T8

AT&W0

AT&W1

AT&Y0

AT&Y1

Loop Test Functions

Terminates test in progress.

Initiates local analog loopback.

Initiates local digital loopback.

Enables digital loopback acknowledgment for remote

request.

Disables digital loopback acknowledgment for remote

request. (Default)

Requests a remote digital loopback (RDL).

Requests a remote digital loopback (RDL) with self

test.

Initiates local analog loopback with self test.

Display Current Configuration and Stored Profiles

Reports the current (active) configuration, the stored

(user) profiles, and the four stored telephone numbers.

Display Modem Connect Status

Store Current Configuration

Stores the current configuration as profile 0.

Stores the current configuration as profile 1.

Profile Selection

The modem will use profile 0. (Default)

The modem will use profile 1.

Enable/ Disable Data Compression

Disables data compression.

Enables MNP 5 data compression negotiation.

Enables V.42bis data compression.

Enables both V.42bis and MNP 5 data compression.

(Default)

AT%C0

AT%C1

AT%C2

AT%C3

&Zn=m

%En

AT%E0

AT%E1

AT%E2

Store Telephone Number

Stores telephone number for later use n= to 3,

m = dialstring.

Enable/Disable Line Quality Monitor and Auto-

Retrain or Fallback/Fall Forward

Disables line quality monitor and auto-retrain.

Enables line quality monitor and auto-retrain.

Enables line quality monitor and fallback/fall forward.

(Default)

Description

Command

AT Command Sets (continued)

\An

\Bn

\Kn

(A)

(B)

(C)

AT\A0

AT\A1

AT\A2

AT\A3

AT\B1-

\B9

\K0

\K1

\K2

\K3

\K4

\K5

\K0

\K1

\K2

\K3

\K4

\K5

\K0

\K1

\K2

\K3

\K4

\K5

Select Maximum MNP Block Size

64 characters.

128 characters. (Default)

192 characters.

256 characters.

Transmit Break to Remote

Break length in 100 ms units. (Default=3.) (Non-error

corrected mode only.)

Break Control

Break received from DTE while in connect state during

on line mode:

Enter on-line command mode, no break sent to the

remote modem.

Clear data buffers and send break to remote modem.

Same as 0.

Immediately send break to remote modemy.

Same as 0.

Send break to remote modem in sequence with

transmitted data. (Default)

\Bn command; received from DTE while in on line

command state:

Purge buffers, immediately send break to remote

modem.

Purge buffers, immediately send break to remote

modem.

Immediately send break to remote modem..

Immediately send break to remote modem.

Send break to remote modem with data.

Break received from remote modem while in connect

state during non error corrected connection:

Purge buffers, immediately send break to DTE.

Immediately send break to DTE.

Send break to DTE in sequence with data.

Command

Description

AT Command Sets (continued) 4.3 DIAL CODES

The following chart shows the Model 2190 dial codes and dial

functions.

Dial Codes

\Nn

\Vn

AT\N0

AT\N1

AT\N2

AT\N3

AT\N4

AT\N5

AT\V0

AT\V1

Operating Mode

Selects normal speed buffered mode.

Selects direct mode.

Selects reliable

Selects auto reliable (error-correction) mode.

Selects LAP-M error-correction mode.

Selects MNP error-correction mode.

Single Line Connect Message Enable

Connect messages are controlled by the command

settings X, W, and S95.

Connect messages are displayed in the single line

format.

+MS

Select Modulation

This extended-format command selects the modulation

and, optionally, enables or disables automode,

specifies the lowest and highest connection rates,

selects u-Law or A-Law code type, and enables or

disables robbed bit signaling generation (server

modem) or detection (client modem) using one to five

subparameters. The command format is:

AT+MS=<mod>

,[<automode>][,[<min_rate>][,[<max_rate][,[<x_law]

[,[<rb_signaling>]]]]]] <CR>

+++

The Escape Code

The Escape Code returns the modem to the command

state from the online state, without releasing the

telephone line.

Command

Description

Dial Code Dial Functions

0-9 Dialing digits 0 to 9.

* The ”star” digit. (tone dialing only)

# The ”gate” digit. (tone dialing only)

A-D DTMF digits A,B,C, and D. Some countries may prohibit

sending of these digits during dialing.

L Re-dial last number. The modem will re-dial the last valid

telephone number. The ”L” must be immediately after

the ”D” with all the following characters ignored.

P Select pulse dialing. pulse dial the numbers that follow until

a ”T” is encountered.

T Select tone dialing. Tone dial the numbers that follow until a

”P” is encountered.

R This command will be accepted, but not acted on.

S=n Dial the number stored in the directory (n = 0 to 3). (See

AT&Zn=m)

! Flash, the modem will go on-hook for a time defined by the

value of S register 29.

W Wait for dial tone. The modem will wait for dial tone before

dialing the digits following ”W”. If dial tone is not detected

within the time specified by S register 7 or 6, the modem

will abort the rest of the sequence, return on-hook, and

generate an error message.

@ Wait for silence. The modem will wait for at least 5 seconds

of silence in the call progress frequency band before

continuing with the next dial string parameter. If the

modem does not detect these 5 seconds of silence before the

expiration of the call abort timer (S register 7), the modem

will terminate the call attempt with a ”NO ANSWER”

message. If busy detection is enabled, the modem may

terminate the call with the ”BUSY” result code. If answer

tone arrives during execution of this parameter, the modem

handshakes.

& Wait for AT&T ”bong” tone for credit card dialing tone

before continuing with the dial string. If the bong is not

detected within the time specified by S register 7 or 6 , the

modem will abort the rest of the sequence, return on-hook,

and generate an error message.

, Dial pause. The modem will pause for a time specified by S

13 14

Dial Codes (continued)

4.4 SUB PARAMETER DEFINITIONS

This section describes the Model 2190 sub parameters. Listed

below are various modulations with the possible rates that the Model

2190 supports.

4.5 FAX COMMANDS

The following section describes the Model 2190 fax commands.

The fax commands are divided into two listings; the first list shows

the fax class 1 commands, and the second list shows the fax class 2

commands.The information listed below identifies the codes and its

function.

4.5.1 FAX CLASS 1 COMMANDS

+FCLASS=n Service class

+FAE=n Data/fax auto answer

+FRH=n Receive data with HDLC framing

+FRM=n Receive data

+FRS=n Receive silence

+FTH=n Transmit data with HDLC framing

+FTM=n Transmit data

+FTS=n Stop transmission and wait

4.5.2 FAX CLASS 2 COMMANDS

+FCLASS=n Service class

+FAA=n Adaptive answer

+FAXERR Fax error value

+FBOR Phase C data bit order

+FBUF? Buffer size (read only)

+FCFR Indicate confirmation to receive

+FCLASS= Service class

+FCON Facsimile connection response

+FCIG Set the polled station identification

+FCIG: Report the polled station identification

+FCR Capability to receive

+FCR= Capability to receive

+FCSI: Report the called station ID

+FDCC= DCE capabilities parameters

+FDCS: Report current session

+FDCS= Current session results

Dial Code Dial Functions

; Return to command state. Added to the end of a dial string,

this causes the modem to return to the command state after

it processes the portion of the dial string preceding the ”;”.

This allows the user to issue additional AT commands may

be placed in the original command line following the ”;”

and/or may be entered on subsequent command lines. The

modem will enter call progress only after an additional dial

command is issued without the ”;” terminator. Use ATH0 to

abort the dial in progress, and go back on-hook.

^ Enable calling tone. Applicable to current dial attempt only.

( ) Ignored. May be used to format the dial string.

- Ignored. May be used to format the dial string.

<space> Ignored. May be used to format the dial string.

<i> Invalid character. Will be ignored.

> If enabled by country specific parameter, the modem will

generate a grounding pulse on the EARTH relay output.

<mod> Modulation Possible Rates (bps) Notes

0 V.21 300

1 V.22 1200

2 V.22bis 2400 or 1200

3 V.23 1200

9 V.32 9600 or 4800

10 V.32bis 14400, 12000, 9600, 7200, or 4800

11 V.34 33600, 31200, 28800, 26400, 24000, Default

21600, 19200, 16800, 14400, 12000,

9600, 7200, 4800, or 2400

64 Bell 103 300

69 Bell 212 1200

74 V.FC 28800, 26400, 24000, 21600, 19200,

16800, or 14400

<automode> Option Selected Notes

0 Automode disabled

1 Automode disabled using V.8 or Default

multi-mode

15 16

Fax Class 2 commands (continued)

+FDIS: Report remote capabilities

+FDIS= Current sessions parameters

+FDR Begin or continue phase C receive data

+FDT= Data transmission

+FDTC: Report the polled station capabilities

+FET: Post page message response

+FET=N Transmit page punctuation

+FHNG Call termination with status

+FK Session termination

+FLID= Local ID string

+FLPL Document for polling

+FMDL? Identify model

+FMFR? Identify manufacturer

+FPHCTO Phase C time out

+FPOLL Indicates polling request

+FPTS: Page transfer status

+FPTS= Page transfer status

+FREV? Identify revision

+FSPL Enable polling

+FTSI: Report the transmit station ID

4.6 VOICE COMMANDS

This section describes the voice commands on the Model 2190.

The list below provides the voice command codes and its function.

#BDR Select baud rate (turn off autobaud)

#CLS Select data, fax, or voice.

#MDL? Identify model

#MFR? Identify manufacturer

#REV? Identify revision level

#SPK= Speakerphone setting

#TL Audio output transmit level

#VBQ? Query buffer size

Voice Commands (continued)

#VBS Bits per sample

#VBT Beep tone timer

#VCI? Identify compression method

#VGT Set playback volume in the command state

#VLS Voice line select

#VRA Ringback goes away timer (originate)

#VRN Ringback never came timer (originate)

#VRX Voice receive mode

#VSD Enable silence deletion (no function, com-

mand response only).

#VSK Buffer skid setting

#VSP Silence detection period (voice receive)

#VSR Sampling rate selection

#VSS Silence detection tuner (voice receive)

#VTD DTMF/tone reporting

#VTM Enable timing mark placement

#VTS Generate tone signals

4.3 REGISTERS

This section provides information on the Model 2190 S-registers.

The codes and functions to change or read registers are listed below.

Also included in this section is a chart on the register codes and its

function.

4.3.1 COMMANDS TO CHANGE OR READ REGISTERS

Listed below are the Model 2190 command guidelines to change

or read registers.This list provides the command codes and describes

the functions of the codes.

ATSn=??? Changes the value of a register.

"n" = number of register

??? = new value of register in decimal

17 18

Inhaltsverzeichnis

Andere Patton electronics Modem Handbücher

Patton electronics

Patton electronics 1193 Bedienungsanleitung

Patton electronics

Patton electronics 1010A Bedienungsanleitung

Patton electronics

Patton electronics 1010B Bedienungsanleitung

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics 1000 Bedienungsanleitung

Patton electronics

Patton electronics 12168 Bedienungsanleitung

Patton electronics

Patton electronics 3010 Bedienungsanleitung

Patton electronics

Patton electronics Model 1065 Bedienungsanleitung

Patton electronics

Patton electronics 1004 Bedienungsanleitung

Patton electronics

Patton electronics 1000P Bedienungsanleitung

Patton electronics

Patton electronics 1004A Bedienungsanleitung

Patton electronics

Patton electronics 2703RC Bedienungsanleitung

Patton electronics

Patton electronics 1170M SERIES Bedienungsanleitung

Patton electronics

Patton electronics OnSite 1069 Bedienungsanleitung

Patton electronics

Patton electronics NetLink 1095 Bedienungsanleitung

Patton electronics

Patton electronics 1094 Bedienungsanleitung

Patton electronics

Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

Patton electronics

Patton electronics 1205 Bedienungsanleitung

Patton electronics

Patton electronics 1088/K Bedienungsanleitung

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics NetLink 1082 Bedienungsanleitung

Patton electronics

Patton electronics 1140RC Bedienungsanleitung

Patton electronics

Patton electronics 1068 Bedienungsanleitung

Patton electronics

Patton electronics 1089/C Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung