Paxton ZKTeco SpeedFace Reader SF1008+ Bedienungsanleitung

ZKTeco SpeedFace Reader - SF1008+ & SF1005-V+

Overview

Setting up Temp only mode

3rd Party

The SpeedFace reader can be used with Net2 to permit or

deny access based on the user’s temperature. When a tem-

perature is detected outside of the set threshold the reader

will notify the user that there is an abnormal temperature

and deny access.

This application note will run through the following modes

of operation:

• Temp only

• Token (MIFARE® only) + Temp

• Face + Temp

Out of the box, the SpeedFace reader will detect a face, determine the temperature and providing it is

below the set threshold, permit access by ring the relay on the reader.

Using this method, the SpeedFace reader relay can be wired in line with a Paxton reader on the Yellow

data port. This will prevent the Paxton reader from functioning until the user has passed the tempera-

ture check.

COM

The default door lock delay on the SpeedFace reader is 5 seconds. To allow sucient time for the user to

present their token to the Paxton reader, you may wish to increase this via the menu on the SpeedFace

reader.

*Allow unregistered access must be enabled in the SpeedFace reader for temperature only to work

properly. 1

3rd Party

Ensure any unused wires are safely terminated.

ACU terminal

+12V

Red LED

Amber LED

Green LED

Wiegand D0

Wiegand D1

NOT USED

ZKteco

NOT USED

WD0

WD1

GND

NOT USED

Setting up modes: Token + Temp & Face + Temp

Net2 ACU Settings

ZKTeco SpeedFace Required Settings

Connecting the reader to a Net2 Plus controller

There are two other main modes of operation; Token + Temp and Face + Temp. In both cases the Speed-

Face reader should be wired to the Net2 plus as shown in the diagram below:

Congure the reader port settings for the ACU the reader has been connected to as shown in the

screenshot below:

Once you have wired up the reader and setup the reader in Net2, the SPEEDFACE reader will need to

be congured. Using the instructions provided with the reader, update the following settings:

• Authentication type - should be set in the menu, select your desired operating mode (Temper

ature is activated in another menu) Access Control->Access Control Options->”Verication

Mode”

• Temp settings - can be changed in the Temp menu. System->Detection Management->”Tem

perature over the range; access denied”

• Mask settings: System->Detection Management->”Enable mask detection” and “Deny access

without mask”

*Users must be enrolled on both the SpeedFace reader, and in Net2. Additional users will need to be

added separately in each system.

3rd Party

+44 (0)1273 811011

paxton.support

support@paxton.co.uk

+44 (0)1273 811011

paxton.support

support@paxton.co.uk

+1(800) 672-7298

usapaxton.support

supportUS@paxton-access.com

+49 (0) 251 2080 6900

paxton.gmbh.support

support@paxton-gmbh.de

+27 (0)21 4276691

paxton.support

support@paxtonaccess.co.za

+11 5715088198

paxton.soporte

soporte@paxton-access.com

+33 (0)157 329356

support@paxtonaccess.fr

paxton.support

+31 (0)76 3333 999

paxton.benelux.support

support@paxton-benelux.com

+32 (0)78485147

paxton.benelux.support

support@paxton-benelux.com

8000 3570 3783

paxton.support

support@paxtonaccess.ae

+1 (864) 751-3501

soporte@paxton-access.com

paxton.soporte

System limitations to note:

Link to manufacturers website: https://zktecousa.com/products/sf1008-plus-sf1005-v-plus/

• Should both a user’s face and temperature be authenticated, but then denied access based

on time zone permissions on the Net2 system, there will be no notication on the panel

• High temperature events cannot be sent from the SPEEDFACE reader to Net2

• Temperature tolerance may need to be changed

Dieses Handbuch passt für folgende Modelle

Andere Paxton Kartenleser Handbücher

Paxton

Paxton Proximity P200 Bedienungsanleitung

Paxton

Paxton Ins-30153 Bedienungsanleitung

Paxton

Paxton Genie WIP2FRTMTP Bedienungsanleitung

Paxton

Paxton Ins-30060 Bedienungsanleitung

Paxton

Paxton Proximity 375-110 Bedienungsanleitung

Paxton

Paxton PROXIMITY Ins-30040 Bedienungsanleitung

Paxton

Paxton PROXIMITY P50 Bedienungsanleitung

Paxton

Paxton PROXIMITY P50 Bedienungsanleitung

Paxton

Paxton PROXIMITY P Ins-30003-EX Bedienungsanleitung

Paxton

Paxton PROXIMITY LCD Ins-30091 Bedienungsanleitung

Paxton

Paxton ins-20800 Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch