Paxton Ins-20601 Bedienungsanleitung

ins-20601

Paxton

Proximity metal readers

1 2

Mounting

Installation guidelines

• Drill a hole in the surface for the rear data cable. Secure the

mounting plate to the surface with four screws as per tting

diagram on page 1.

• Suitable screws and xings are provided for tting the plate to

a wall. Mount the reader on its backplate and secure with the

security screws using the Allen key supplied.

• Ensure the data cable has free access at the rear.

Wiring

3 4

390-737

390-747

390-757

110mA 110mA 110mA

Current

@ 12V DC

Operating

temperature

Waterproof

HID

compatible

Handsfree

Mounted on

metal surface

-35°C - +66°C

-31°F - +151°F

Technical Help

1 - Readers/Keypads not working.

• Software settings - Conrm that the settings of the reader or

keypad are correct.

• Connections - Check the wiring and integrity of the connectors. If

possible, test this reader on the other port.

• Extended cable - Belden 9538/9540 should be used up to a

maximum of 500 feet. Twisted pair alarm cable should not be

used. To conrm that an extended reader cable is not at fault, wire

the reader directly to the port.

• Supply voltage - Conrm that the voltage is within specication.

(see table)

• User token - Conrm that the user token used for testing is OK by

presenting it to a known working reader.

• Interference - Conrm whether the reader works when tested ‘in

hand’ and not mounted on the wall.

• PROXIMITY readers should not be mounted back to back or close

to other RF devices.

2 - Readers / Keypads - Extending cable.

• Only Belden CR9538 / 9540 or a UL equivalent can be used for

cable extensions. The maximum run is 500 feet.

3 - Net2 - Using a door reader as a desktop reader.

• It is possible to congure a door reader to operate as a desktop

reader:

1 - Select the doors menu in the left hand Net2 pane.

2 - Click on the door you wish to change the reader to act as a desktop

reader.

3 - Under the relevant reader tab, change the reader operating mode to

‘Desktop Reader’.

4 - The PC displays‘Would you like to accept desktop reader events from

this reader at the PC?’; click‘Yes’

Now when you present a blank or existing token to that reader it will

allow you to add this new token or edit the existing one.

NOTE: Remember to return the operating mode to the original setting

once the cards have been read or users will not be able to gain access

through the reader. KP Reader - Ensure that Keypad type is set to ‘None’,

otherwise the Desktop reader option will not be available.

4 - Net2. What to do if a user has no access - Check the reader LED’s

when a card is shown.

• No LED’s - the reader has no power.

• No change in display - try the card on a known working reader. If

there is still no response, replace the card.

• Green LED ashing when a card is presented; check relay 1 LED to

check for activity and also the lock wiring.

• Red LED is ashing when a card is presented; check the validity of

the user at the PC.

• Check user’s access level and ensure they should have access by

clicking on Current Validity.

• Check the ‘Expires end’ date and conrm this has not been past.

• Reinstate the ACU from the doors screen. Select the ACU’s you

wish to reinstate and then click OK.

Specications

5 6

+44 (0)1273 811011

paxton.support

support@paxton.co.uk

+44 (0)1273 811011

paxton.support

support@paxton.co.uk

+1(800) 672-7298

usapaxton.support

supportUS@paxton-access.com

+1(800) 672-7298

usapaxton.support

supportUS@paxton-access.com

+49 (0) 251 2080 6900

paxton.gmbh.support

support@paxton-gmbh.de

+31 (0)76 3333 999

paxton.benelux.support

support@paxton-benelux.com

+31 (0)76 3333 999

paxton.benelux.support

support@paxton-benelux.com

+31 (0)76 3333 999

paxton.benelux.support

support@paxton-benelux.com

+33 (0)157 329356

support@paxtonaccess.fr

+27 (0) 272 14276691

support@paxtonaccess.co.za

+44 (0)1273 811011

paxton.support

support@paxton.co.uk

Ce dispositif est conforme à la section 15 du règlement de la FCC. Le fonctionnement est soumis aux deux

conditions suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif doit accepter

toute interférence reçue, y compris des interférences qui peuvent causer un fonctionnement non souhaité. Tout

changement ou modication non agréé par la partie responsable de la mise en conformité peut entraîner une

interdiction d'utilisation de l'équipement.

Conformité et limitations du produit

Ce dispositif est conforme au(x) standards RSS de l'industrie Canadienne sans-licence. Le fonctionnement est

soumis aux deux conditions suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif

doit accepter toute interférence reçue, y compris des interférences qui peuvent causer un fonctionnement non

souhaité.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Changes or modications not expressly approved by

the party responsible for compliance could void the user's authority to operate the equipment.

To comply as a UL listed installation, the following conditions must apply:-

• Server based functions (Antipassback, Time and Attendance, etc) have not been evaluated by UL and

cannot be used for UL 294 installations.

• Where an equivalent cable / wire is used it must be ‘ UL Listed ‘All interconnecting devices must be UL

Listed.

• The use of Wiegand readers and the conguration software has not been evaluated by‘UL’

• For CAN/ULC-S319 installations, terminals, leads and wiring methods must comply with CSA, C22.1,

Canadian electrical code, Part 1, safety standards for electrical installations.

• The use of any add-on, expansion, memory or other module manufactured or supplied by the

manufacturer’s representative will invalidate the CAN/ULC-S319 certication.

• Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and

the authorities having jurisdiction.

Pour que l’installation répond aux normes UL, les conditions suivantes sont applicables:-

• Les fonctions serveur (Antipassback, Pointage, etc.) n’ont pas été évalué par l’UL et ne peuvent pas être

utilisé pour les installations UL294.

• L’utilisation des lecteurs Wiegand et le logiciel de conguration n’ont pas été évalués par ‘UL’

• Quand un cable équivalent est utilisé, il doit être‘listé UL’Tout appareil d’interconnexion doit être listé UL

• Pour les installation CAN/ULC-S319, les terminaux, câbles et méthodes de câblage doivent être en accord

avec CSA, C22.1, code électrique canadien, Partie 1, standards de sécurité pour les installations électriques.

• L’utilisation de tout rajout, extension, mémoire ou module fabriqué ou fourni par le représentant du

fabricant invalidera la certication CAN/ULC-S319

• Les méthodes de câblage doivent être en accord avec le code nation électrique (ANSI/NFPA70), codes

locaux et les autorités ayant la juridiction.

North America:- Product compliance and limitations

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

The declaration of conformity is available on request. Contact details are provided at:

http://paxton.info/596

These products are not suitable for retail sale. All warranties are invalid if these products are not installed by

a competent person.

FCC Compliance

Conformité FCC

http://paxton.info/1606

Made in the UK

01/29/2014

Inhaltsverzeichnis

Andere Paxton Tor Handbücher

Paxton

Paxton ins-20801 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

Paxton ins-20601 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken