PCchips M935ALU Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without writtenconsent ofthe au-

thor.

Version 5.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 6

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 24

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 36

iii

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction............................................................................................................1

Checklist.................................................................................................................1

Standard Items ...................................................................................................1

Features..................................................................................................................2

Choosing a Computer Case................................................................................3

Mainboard Components.......................................................................................5

CHAPTER 2 6

Installing the Mainboard 6

Safety Precautions................................................................................................6

Quick Guide...........................................................................................................6

Installing the Mainboard in a Case.....................................................................7

Checking Jumper Settings...................................................................................7

Setting Jumpers .................................................................................................7

Checking Jumper Settings.................................................................................8

Jumper Settings.................................................................................................8

Connecting Case Components...........................................................................9

The SW1 Connector........................................................................................10

Installing Hardware.............................................................................................11

Installing the Processor...................................................................................11

InstallingMemoryModules............................................................................14

Installing a Hard Disk Drive/CD-ROM ..........................................................15

Installing a Floppy Diskette Drive ..................................................................17

InstallingAdd-on Cards..................................................................................18

Connecting Optional Devices..........................................................................20

ConnectingI/ODevices.....................................................................................22

CHAPTER 3 24

Using BIOS 24

About the Setup Utility........................................................................................24

The Standard Configuration............................................................................24

Running the Setup Utility................................................................................25

Using BIOS..........................................................................................................25

Standard CMOS Setup Page............................................................................26

Advanced Setup Page......................................................................................27

Power Management Setup Page......................................................................29

PCI / Plug and Play Setup...............................................................................30

Load Optimal Settings.....................................................................................31

Load Best Performance Settings.....................................................................31

Features Setup Page.........................................................................................31

CPU PnP Setup Page.......................................................................................33

HardwareMonitorPage..................................................................................34

ChangePassword ............................................................................................35

Change or Remove the Password....................................................................35

Exit ..................................................................................................................35

CHAPTER 4 36

Using the Mainboard Software 36

About the Software CD-ROM............................................................................36

Auto-installing under Windows 98....................................................................36

Running Setup.................................................................................................38

Manual Installation..............................................................................................39

Utility Software Reference.................................................................................40

Introducing the Mainboard

Congratulations on purchasing this mainboard. This mainboard has aSocket-

478 processor socket for Intel Pentium 4 type of processors supporting front

side bus (FSB) speeds up to400 MHz.

The mainboard integrates one of the series of SiS650 chipset; SiS650 or

SiS650GL or SiS651 Northbridge and SiS961 (or SiS962) Southbridge chip-

sets that supports built-in AC97 Codec, 2DDR + 2 SDR modules up to 2GB

system memory, and provide Ultra DMA 33/66/100/(133)function. In addition,

the mainboard integrates a256-bit 3D/2D Graphics Engine, Video Accelera-

tor and Advanced Hardware Acceleration MPEGI/MPEGII Video Decoder for

the Intel Pentium 4 series based PC systems.

This mainboard is Micro ATX size and has power connectors for an ATX

power supplyand measures 244 x 244mm.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•Software support CD

•One VGA extension bracket

•The User’s Manual

Notice to user:

This manual is provided to accommodate the P4S5MG, P4S5MG/GL and P4S5MG/651

mainboards. To identify the type of mainboard you have, please refer below:

•P4S5MGmainboard incorporates the SiS650 Northbridge and SiS961

Southbridge chipset.

•P4S5MG/GL mainboard incorporates the SiS650GL Northbridge and SiS961

(or SiS962) Southbridge chipset.

•P4S5MG/651 mainboard incorporates the SiS651 Northbridge and SiS961

(or SiS962) Southbridge chipset.

Processor •The mPGA Socket 478

•Supports Intel Pentium 4 series CPUs

•Supports up to 400/533 MHz system bus

Note: Only when the mainboard incorporates the

SiS651 Northbridge chipset can the system bus

support up to 533 MHz.

Chipset The SiS650/SiS650GL/SiS651 Northbridge and

SiS961/SiS962 Southbridge chipsets are based on an innova-

tive and scalable architecture with proven reliability and

performance.

The mainboard may support either of the Northbridge and

Southbridge chipset mentioned above. Refer below for the

combination and respective details:

•SiS650 Northbridge and SiS961 Southbridge –Support

up to 400 MHz system bus, ATA 100 interface and DDR

266.

•SiS650GL Northbridge and SiS961 Southbridge -Sup-

port up to 400 MHz system bus, ATA 100 interface and

DDR 266. (Note: Without 4xAGP slot)

•SiS651 Northbridge and SiS962 Southbridge –Support

up to 533 MHz system bus, ATA 133 interface, DDR 333

and USB 2.0 controller.

Memory •Two 168-pin DIMM slots for SDRAM memory modules

•Two 184-pin DIMM slots for DDR memory modules

•Support SDRAM up to 133 MHz /DDR up to 266 MHz

memory bus

•Maximum installed memory is 2GB

Notes: 1. For SiS962Southbridge chipset, DDR can sup-

port up to 333 MHz memory bus.

2. Do not use SDRAM and DDR concurrently.

Expansion Slots •One AMR slot for a special audio/modem riser card

•One 2x/4xAGP slot*for AGP 2.0-compliant interface

•Two 32-bit PCI slots for PCI 2.2-compliant bus interface

Onboard IDE

channels •Primary and Secondary PCI IDE channels

•Support for PIO (programmable input/output) modes

•Support for Multiword DMA modes

•Support for Bus Mastering and Ultra DMA 33/66/100/133

modes

*When the mainboard incorporates the SiS650GL Northbridge chipset, the mainboard will not sup-

port the 4xAGP slot.

Power

Supply and

Power

Management

•ATX power supply connector

•Meets ACPI 1.0b and APM 1.2 requirements, keyboard

power on/off

•Supports RTC Alarm, Wake On Modem, AC97 Wake-Up

and USB Wake-Up

AC’97 Audio

Codec •Compliant with AC’97 2.2 specification

•Full-duplex Codec with independent and variable sam-

pling rate

•Earphone Buffer Built-In, SNR up to 90db

•4Ch DAC, support 4-channel speak-out

•Advanced power management support

Onboard VGA •Supports AGP V2.0 Compliant

•Supports AGP 4X/2X*interface and Fast Write Transac-

tion

•Supports high performance & high quality 3D Accelera-

tor—A built-in 256-bit 3D engine, up to 143 MHz 3D

engine clock speed

•Supports high performance 128-bit 2D Accelerator—

Ultra-AGPIITM

2GB/s data read for all 2D engine functions

•Maximum Share Memory size is 64MB

Built-in Ethernet

LAN (optional) •Built-in 10BaseT/100BaseTX Ethernet LAN

•SiS961 Embedded Fast Ethernet MAC and onboard

Realtek RTL8201 LAN PHY compliant with IEEE802.3u

100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD

standards

•Compliant with ACPI 1.0 and the Network Device Class

Power Management 1.0

•High Performance provided by 100Mbps clock generator

and data recovery circuit for 100Mbps receiver

USB 2.0 (see note)

The USB 2.0 Controller is compliant with Universal Serial Bus

Specification Revision 2.0.

The USB 2.0 supports data transfer rates up to 480MB/sec for

high-speed devices and specifies a microframe that will be

1/8th of a 1msec frame. This allows the USB 2.0 devices to

have small buffers even at high data rates.

The USB 1.1 connectors and other full speed cables can sup-

port the higher speed of USB 2.0 without any changes.

The chipset has the following advanced USB features:

•Compliant with Enhanced Host Controller Interface

(EHCI) Specification Revision 0.95 and Universal Host

Controller Interface (UHCI) Specification Revision 1.1

•PCI multi-function device consists of two UHCI Host Control-

lers for full/low-speed signaling and one EHCI Host

Controller core for high-speed signaling

•Supports PCI-Bus Power Management Interface Specifi-

cation release 1.1

•Legacy support for all downstream facing ports

Note: This feature is only present when SiS962

Southbridge chipset is onboard.

*Except when the mainboard incorporates the SiS650GL Northbridge chipset.

Onboard I/O

Ports •Two PS/2 ports for mouse and keyboard

•Two serial ports

•One parallel port

•One MIDI/game port

•Four USB ports (two backpanel ports, onboard USB

header providing two extra ports)

•Audio jacks for microphone, line-in and line-out

Hardware Moni-

toring Built-in hardware monitoring for CPU & System temperatures,

fan speeds and mainboard voltages.

Onboard Flash

ROM Supports Plug and Play configuration of peripheral devices

and expansion cards

Dimensions Micro ATX form factor 244 x 244mm

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the micro-ATX system case. Some features on

the mainboard are implemented by cabling connectors on the mainboard to

indicators and switches on the system case. Ensure that your case supports

all the features required. The mainboard can support one floppy diskette drive

and four enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

Thismainboardhasamicro-ATX form factor of 244 x 244 mm. Choose a case

thataccommodates this form factor.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

•Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

•Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

•Leave components in the static-proof bags they came in.

•Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 5

Installing the Mainboard in a Case Go to page 7

Setting Jumpers Go to page 7

Installing Case Components Go to page 8

Installing the CPU Go to page 11

Installing Memory Go to page 14

Installing an HDD and CD-ROM Drive Go to page 15

Installing an FDD Go to page 17

Installing Add-on Cards Go to page 18

Connecting Options Go to page 20

Connecting Peripheral (I/O) Devices Go to page 22

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PCchips Hauptplatine Handbücher

PCchips

PCchips M825 Series Bedienungsanleitung

PCchips

PCchips M852 Bedienungsanleitung

PCchips

PCchips M921 Series Bedienungsanleitung

PCchips

PCchips M726MRT Bedienungsanleitung

PCchips

PCchips M786 Series Bedienungsanleitung

PCchips

PCchips M848ALU Bedienungsanleitung

PCchips

PCchips M728 Bedienungsanleitung

PCchips

PCchips A21G Bedienungsanleitung

PCchips

PCchips M787CLR Bedienungsanleitung

PCchips

PCchips M939LU Bedienungsanleitung

PCchips

PCchips M930 Series Bedienungsanleitung

PCchips

PCchips M925ALU Bedienungsanleitung

PCchips

PCchips M755LMR Bedienungsanleitung

PCchips

PCchips M935 Series Bedienungsanleitung

PCchips

PCchips M930LR Bedienungsanleitung

PCchips

PCchips M7 Bedienungsanleitung

PCchips

PCchips M922ULR Bedienungsanleitung

PCchips

PCchips M756T Bedienungsanleitung

PCchips

PCchips M757MR Bedienungsanleitung

PCchips

PCchips M812 Series Bedienungsanleitung

PCchips

PCchips M863G Bedienungsanleitung

PCchips

PCchips A16 Bedienungsanleitung

PCchips

PCchips M922 Series Bedienungsanleitung

PCchips

PCchips M754 Plus Series Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung