Peavey PXR 1000 Bedienungsanleitung

www.peavey.com

PXR™1000

1000-WATT, 8-Channel Powered Mixer

Operating

Manual

###########

ThisdevicecomplieswithPart15oftheFCCrulesandIndustryCanadalicense‐exemptRSSStandard(s).Operationis

subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust

acceptanyinterferencereceived,thatmaycauseundesiredoperation.

LeprésentappareilestconformeauxCNRd’lndustrieCanadaapplicablesauxappareilsradioexemptsde

licence.L’exploitationestautoriséeauxdeuxconditionssuivantes:(1)I’appareilnedoitpasproduirede

brouillage,et(2)I’utilisateurdeI’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesile

brouillageestsusceptibled’encompromettrelefonctionnement.

Warning:ChangesormodificationstotheequipmentnotapprovedbyPeaveyElectronicsCorp.canvoidthe

user’sauthoritytousetheequipment.

Note–ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,

pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful

interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,

whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotryandcorrectthe

interferencebyoneormoreofthefollowingmeasures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment.

FCC/ICESCompliancyStatement

###########

###########

###########

ENGLISH

PXR™ 1000

Powered Mixers

Congratulations on the purchase of your new PXR 1000 powered mixer from Peavey®. The Peavey PXR 1000 is a revolutionary all in

one powered mixer. It provides up to eight combination XLR and 1/4”inputs using Peavey’s award winning mic preamps, and 500

watts per channel for crystal clear audio reproduction. The Peavey PXR 1000 uses exclusive and patented features like Mid Morph®

to accurately help improve tone and clarity of vocals. Feedback is quickly and easily identied and removed with Peavey’s 7-band

graphic EQ combined with our patented and revolutionary FLS®Feedback Locating System. The PXR 1000 is equipped with

Peavey’s exclusive Kosmos®-C technology which drastically enhances both the low and high end of the audio spectrum. Foot-

switchable built in 24-bit digital eect compliments the already feature packed unit. Connect almost anything to this versatile

mixer via the onboard 1/4”, RCA and 1/8”mini jacks.

Before you begin using your powered mixer it is very important to ensure that the product has the proper AC voltage

supplied. You can nd the proper voltage for your amp printed next to the IEC line (power) cord on the rear panel of the unit.

FEATURES:

• FLS Feedback Locating System

• Mid-Morph EQ

• Kosmos-C

• On-board 24- bit digital effects with mute button

• Digital effects parameter control

• Combination XLR and 1/4” input jacks

• Dual 7-Band Graphic EQ with FLS

• Master Mute for channels 1-7

• Footswitchable effects defeat

• Global Phantom Power

• RCA, 1/8” Media input

• Bluetooth® (PXR 1000 model)

• Selectable Main or Monitor dual power section

• RCA Record outputs

• LED Meter bridge

• Power amp sub-sonic filtering

• Clip light and signal present indicator

• Main line level 1/4” output

• DDT™Speaker protection circuit

VENTILATION: For proper ventilation, allow 6” (15.5 cm) clearance on all sides.

HIGH EQ

This High EQ shelving type of active tone control varies the treble

frequencies (+/- 15 dB at 12 kHz) and is designed to remove noise or

add brilliance to the signal, depending on the quality of the source.

MID-MORPH®EQ

Where most mid-range controls work at just one frequency, the

Mid-Morph works at two. When turned counterclockwise, it cuts at

250 Hz to reduce frequencies that muddy the sound. When turned

clockwise, it boosts at 4 kHz to add intelligibility to vocals. Either

way, improved vocal or instrument denition can be achieved.

LOW EQ

A shelving type of EQ that varies the bass frequency levels (+/-

15 dB at 80 Hz). Low EQ adds depth to thin-sounding signals or

cleans up the muddy ones. As with any EQ, use sparingly. Too

much of this EQ can give you a booming bottom end.

MONITOR SEND

The monitor send adjusts the level of the channel signal added to

the monitor send. Keep in mind the monitor send can be assigned

to one of two power ampliers and power an external monitor

speaker.

EFX - DIGITAL EFFECTS

This control adjusts the level of the channel signal added to the

eects mix. The signal is sent to the internal eects processor.

Turning the knob to the left (0) will turn o eects on the associ-

ated channel, while turning the knob to the right will increase the

amount of the selected eect.

LEVEL

This control sets the signal level sent to the main mix.

CLIP

When this LED turns or blinks red, is an indication that the signal

coming into the channel is too strong potentially causing distor-

tion. Turn down the Level control (6) until the Clip light is no longer

present. If you are having diculty getting a clean signal, try vary-

ing the output of the connected device.

SIG

When this LED is green, it is an indication the mixer is receiving

signal at the input of the channel. If you hare having trouble getting

sound out of the mixer and this LED is not on, check the micro-

phone, instrument or cable that is connected to the channel.

MIC/LINE INPUT

This combination input jack can accept either a 1/4” (balanced or

unbalanced) input or a XLR balanced, low-impedance connection.

The tip is positive on the 1/4”balanced input, and pin 2 is positive

on the XLR.

MIC/HI Z INPUT

Channel 7 line input is a Hi-Z unbalanced input for use with high

impedance microphones, acoustic/electric guitars or other high

impedance sources equipped with a 1/4" plug (TS).

Channel Strip

CHANNEL CONTROLS

Media Input

12a

12b

XLR BALANCED INPUT

Channel 8 is designed specically for pre-recorded (pro-

gram) music, but can also be used with a microphone.

This XLR input provides a balanced low impedance con-

nection.

MIC OR MEDIA SELECT BUTTON

This control selects between the low impedance XLR (9)

and the RCA / 1/8”, or Bluetooth® signal.

MEDIA INPUT

These inputs, both RCA and 1/8”accept a stereo input

from the output of an MP3 player, CD player, tape deck or

other similar device.

FLS®

When feedback occurs, the corresponding LED of the

frequency that is closest to the frequency that is feeding

back will illuminate over the slider to be adjusted. Slowly

bring the corresponding slider down until feedback is

gone. The LED will remain illuminated for a few seconds

after the feedback is gone.

GRAPHIC EQ

These 7-band EQs are designed for 12dB cut or boost.

These EQs are used to make minor adjustments to the

overall mix and should be used sparingly.

AMP LEVEL LED LADDER

These LEDs indicated the signal level going to the power

amplier. The top LED indicates LIMIT and activation

of our revolutionary DDT™speaker protection circuit.

Peavey’s award winning speaker protection circuit is

built into the PV®8500/PVi8500 and activated automati-

cally to maximize the power amplier without fear of

distortion.

POWER AMP INPUT SELECT

This control allows the user to select whether the 2nd

power amplier receives its signal from the Master Vol-

ume (18) or from the Monitor Volume (17) control. This

allows the user to run both power amps for mains, or use

power amp 1 for mains and power amp 2 for monitors.

MONITOR VOLUME

The master level control adjusts the level of the signal

coming out the Monitor send 1/4” jack. It can also be

assigned to feed the 2nd power amplier via selector

switch (16).

MASTER VOLUME

The master level control for the main mix and the overall

volume of the powered mixer.

12a

12b

15 16

Effects Section

KOSMOS®C

The Kosmos -C module uses special circuitry

to enrich the sound of your system. The

low control is not just a simple bass boost.

It provides ‘natural bass enhancement’ by

adding harmonically related bass signals that

track envelope of the original signal. The

Kosmos-C, High control can be used to add

clarity to dull signals.

MASTER MUTE LED

When the LED is ON it indicates the master

mute is activated.

MASTER MUTE

Depressing this button mutes channels one

through seven, preventing signal from pass-

ing to the power amplier. This button does

not aect channel 8.

EFFECTS TYPE TABLE

This table lists the type of eects available

and the abbreviation used for that eect in

the rst character of the LED display. The

chart also lists the parameter associated with

the eect that is controlled by turning en-

coder 24. A more detailed list of eects can

be found at the end of this manual.

EFX LED

This LED indicates the type of eect currently

selected. When turning encoder 27 the dis-

play will ash until the encoder is depressed,

selecting a new eect.

PARAMETER CONTROL

This encoder controls the parameter associ-

ated with the selected eect, listed both on

the mixer (23) and in this manual. The param-

eter control is used to make adjustments to

the sound of the eect.

CLIP LED

This LED blinks RED when the signal to the eects section is too hot and is causing distortion. Find the

source of the hot signal by reducing the EFX SEND (5) on each channel until the LED is no longer clipping

(blinking red).

EFX MUTE

When pushed this button bypasses the eects section, letting the user listen to the dry signal. When de-

pressed and muted, LED 23 displays two dashes “--”.

EFFECTS SELECT

Turn and push this encoder to select the desired eect.

25 26 27

Front Panel

PHANTOM POWER

This switch when depressed, applies +15 VDC to all input XLR connectors to power microphones that

require phantom power.

Caution: When phantom power is switched on‚ make sure that any channel you are plugging a micro-

phone into is turned down and the Master Main and Monitor controls are set to minimum. Otherwise‚

there will be a loud pop in the system. For best results, rst plug in all microphones into their respective

channels before phantom power is switched on. This reduces noise through the system and reduces the

chance of damage to the microphones. If phantom power is used‚ do not connect unbalanced‚ dynamic

microphones or other devices to the XLR inputs that cannot handle this voltage. (Some wireless receiv-

ers may be damaged. Consult their manuals.) The line input jacks are not connected to the phantom

supply and are safe for all inputs (balanced or unbalanced). An unbalanced to balanced impedance

converter such as the Peavey 5116 or a Peavey 1:1 Interface Adapter may also be used to isolate a micro-

phone from phantom voltage.

BLUETOOTH® ACTIVATION

This switch activates the PXR 1000's Bluetooth® connectivity, allowing you to stream audio from any Blue-

tooth® capable device. See page 22 for instructions on Bluetooth® operation.

BLUETOOTH® LED

Indicates that the PXR 1000 is receiving signal from a Bluetooth® device. LED blinks while nding a signal

and is solid once paired with the Bluetooth® device.

RECORD LEVEL

This knob adjusts the main signal level sent to the RCA record outs.

RCA RECORD OUT

This pair of RCA jacks provides a signal to the recording inputs of a CD recorder, stereo tape deck, or other

recording device.

NOTE: Do not connect a single device to the Media In (12a/12b) and Record Out (33). This improper

setup forms a loop, which can cause severe feedback. Use separate devices for recording and playback.

FOOTSWITCH

This 1/4”TRS (tip ring sleeve) jack accepts a momentary 1/4”TRS dual button footswitch (Peavey part num-

ber 03014070) designed to defeat the eects on all channels and activate the MASTER MUTE switch (21).

This function is extremely useful for playing program music during breaks.

MONITOR OUT

This 1/4”jack provides a signal from the monitor mix (4) for an external power amplier. An external

power amplier, such as our IPR® series of ampliers, can then drive additional monitor speakers.

MAIN OUT

This 1/4”jack provides a signal from the main mix (after the graphic EQ) for an external power amplier.

An external power amp, such as our IPR series of ampliers, can then drive additional speakers.

28 3231 33 34 35

29 30

USB/SD MP3 Player

MODE

If both, a memory stick and SD card are present, a short press of the MODE button will change between the

USB input and the SD card input. A long press of the MODE button will shut o the MP3 player. Another

long press is needed to turn it back on.

PLAY/PAUSE

A short press of the PLAY/PAUSE button causes the operation to change from PLAY to PAUSE or from PAUSE

back to PLAY. A long press of the PLAY/PAUSE button will put the player into navigation mode. When in

navigation mode the player can toggle between multiple folders on the memory device. The le folder num

is displayed at the top of the screen while the le folder name is at the bottom. The “track skip (42)” buttons

can be used to toggle between the folders on the memory device. Once the desired folder is found, press

“PLAY/PAUSE” to select the folder. The rst song in the folder will begin playing.

STOP

Press the STOP button to stop a le that is playing.

REPEAT

Pressing the REPEAT button toggles the function between ALL, RANDOM and SINGLE.

ALL: Repeats all songs.

RANDOM: Plays songs in random order.

SINGLE: Repeats a single song.

Note: The REPEAT functions only apply to the songs in the selected folder.

TRACK SKIP

In playback mode the TRACK SKIP buttons let you select the track to play.

A short press skips to the next track. A long press allows you to fast forward/rewind through a song. Hold

the button down until the desired playback point is found. Release the button and the song will start play-

ing. In navigation mode, the TRACK SKIP buttons are used to increment/decrement through the folders on

the memory device.

USB DRIVE SLOT

On the right side of the device is a USB drive slot where a USB memory stick can be connected. The player

will accept a memory stick up to 32Gb.

SD CARD SLOT

To connect the SD card, push the card completely in the slot until it clicks into place. The player will accept a

SD card up to 32Gb in size.

36 37 38 39 40 41

Back Panel

POWER SWITCH

This is the main power switch.

FUSE

This is the main safety fuse for the AC line voltage. Only

replace with a fuse of the exact type and rating. If the

fuse continues to open, do not over fuse. Take the unit

to an authorized Peavey service center.

NOTE: If the main AC voltage is changed, the fuse must

also be changed to one of the appropriate rating for

the voltage you are switching to.

AC POWER INLET

This is the receptacle for an IEC line cord, which provides

AC power to the unit. Connect the line cord to this

connector to provide power to the unit. Damage to the

equipment may result if improper line voltage is used.

(See line voltage marking on unit).

Never break o the ground pin on any equipment. It

is provided for your safety. If the outlet used does not

have a ground pin, a suitable grounding adapter should

be used and the third wire should be grounded proper-

ly. To prevent risk of shock or re hazard, always make

sure that the amplier and all associated equipment is

properly grounded.

NOTE: FOR UK ONLY

As the colors of the wires in the mains lead of this appa-

ratus may not correspond directly with the colored mark-

ings identifying the terminals in your plug, proceed as

follows: (1) The green and yellow wire must be connected

to the terminal which is marked with the letter E, or by

the earth symbol, or is colored green, or green and yel-

low. (2) The blue wire must be connected to the terminal

which is marked with the letter N, or the color black. (3)

The brown wire must be connected to the terminal which

is marked with the letter L, or the color red.

VOLTAGE SELECTOR SWITCH

This switch allows the user to select between 115VAC /

60Hz or 230VAC / 50Hz. To change the voltage selector,

you must first unscrew and remove the plastic cover that

protects the switch. After changing the voltage, please

replace the plastic cover to ensure the voltage level is

not inadvertently altered.

NOTE: The fuse MUST be changed to the appropriate

value to match the voltage you have selected. Please see

the note on the back of the mixer for the correct value.

MAIN / MONITOR SPEAKER OUTPUTS

A two-conductor 1/4" speaker output and Speakon jack

are assigned to each channel. Each amp is rated at 4

ohms minimum impedance. You may connect either

one 4-ohm, one 8-ohm or two 8-ohm speakers to

each output. Do not operate below rated minimum

impedance. For maximum power transfer, be sure to use

speaker cables and not instrument cables to connect to

the speakers. We recommend the use of 18-gauge or

larger speaker wire.

Bluetooth® operation

To listen to your music via Bluetooth wireless connection, you need to pair

(link) your PXR 1000 with your Bluetooth phone and/or music device.

1. Turn o any Bluetooth devices previously paired with your PXR 1000.

2. Turn on the Bluetooth feature on your phone or music device.

3. Slide the switch (29) to the right to turn on the Bluetooth feature.The

Bluetooth LED (30) will ash to indicate your PXR 1000 is in discoverable mode.

4. Place your phone or music device in Bluetooth search mode.

The phone or music device will now begin searching for your PXR 1000.

5. Select Bluetooth audio from search results on your phone or music

device.

6. Select OK or Yes to pair your speaker system with your phone or music

device.

When your PXR 1000 successfully pairs and connects with your phone

or music device, the Bluetooth indicator changes from ashing green to

steadily lit. You will now be able to play music from your connected music

source through your PXR 1000. The level can either be adjusted from the

connected source or by the level control in Channel 8.

* Wireless range can vary depending on Bluetooth class of source device,

and be subject to interference from obstructions such as walls or other

electronic devices.

29 30

Inhaltsverzeichnis

Andere Peavey Musikmixer Handbücher

Peavey

Peavey UMA 1502 Bedienungsanleitung

Peavey

Peavey SMR 821 Bedienungsanleitung

Peavey

Peavey XR 700C Bedienungsanleitung

Peavey

Peavey PA 400 Bedienungsanleitung

Peavey

Peavey AAM 1662 Bedienungsanleitung

Peavey

Peavey CD MIX 7032 Bedienungsanleitung

Peavey

Peavey AMA 1200 Bedienungsanleitung

Peavey

Peavey SRC 4018 FC Bedienungsanleitung

Peavey

Peavey XR 696 Bedienungsanleitung

Peavey

Peavey XR-AT Bedienungsanleitung

Peavey

Peavey Architectural Acoustics MMA 800T Bedienungsanleitung

Peavey

Peavey Unity Series 500 Bedienungsanleitung

Peavey

Peavey XR 600G Bedienungsanleitung

Peavey

Peavey SRC 421-16 Bedienungsanleitung

Peavey

Peavey RQ 4300 Series Bedienungsanleitung

Peavey

Peavey SRC 6024 Bedienungsanleitung

Peavey

Peavey PVi 8 Bedienungsanleitung

Peavey

Peavey Unity DR16 Bedienungs- und Wartungsanleitung

Peavey

Peavey Automix 4 Bedienungsanleitung

Peavey

Peavey 24FX Mixer Bedienungsanleitung

Peavey

Peavey XRD 680 PLUS Bedienungsanleitung

Peavey

Peavey LM 16s Bedienungsanleitung

Peavey

Peavey IRM 8150 Bedienungsanleitung

Peavey

Peavey XR 800 Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

SoundCraft

SoundCraft B400 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung