Peavey PVX p 15 Bedienungsanleitung

Features and specifications are subject to change without notice.

Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301

(601) 483-5365 • FAX (601) 486-1278 • www.peavey.com

EX000030

FCC/ICES Compliancy Statement

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation

is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, that may cause undesired operation.

Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de brouillage, et (2)

I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the user’s

authority to use the equipment.

Note – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try and correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-

ronment.

FCC Radiation Exposure Statement

is equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. is

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC Radiation Exposure Statement

is equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. e an-

tenna should be installed and operated with minimum distance of 20 cm between the radiator and your body.

is transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non

contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source

de rayonnements et votre corps. L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre

antenne ou autre émetteur.

Loudspeaker System Specifications

PVX™p 15 Bluetooth®

Cover Page (With Picture & Logo)

PVX™p 15 Bluetooth®

Thank you for purchasing the powered Peavey® PVX™p 15 Bluetooth® speaker

system. The PVX™p 15 Bluetooth® features a reliable bi-amped power section

that provides a total of 980 Watts of peak dynamic power with DSP based

compression and limiting. Featuring a 15” heavy-duty woofer with a 2 3/8 inch

voice coil and 50 ounce magnet, and the RX14™ compression driver with a 1.4

inch titanium diaphragm on a 100 degree horizontal x 50 degree vertical pattern

asymmetrical horn. The PVX™p 15 Bluetooth® provides two channels with a

balanced input via a combination jack that accepts balanced TRS 1/4 inch input

as well as a balanced XLR input. A switch is provided to change between line

level gain and mic level gain. A third channel is for a Bluetooth® source, or

alternatively a 1/8" AUX input jack. Each channel has an adjustable Level

control, and a three-band EQ section. There is a balanced output, a Male XLR,

that can feed the mixed signals from the three channels out to another

component. A front baffle LED indicator that can be set to light when power is

on, and when the “soft-limiting” DDT circuit is activated, or turned off altogether.

The LCD display and EQ presets, along with other DSP operating parameters

are accessed via a one-knob selector.

Features

* Two-way bi-amped sound reinforcement enclosure

* 15” heavy-duty woofer with 2 3/8” voice coil & 50 oz. magnet

* RX14™ compression driver, with 1.4 inch titanium diaphragm

* Reliable fan-cooled power amps with DSP protection

* Total of 980W peak dynamic power

* DSP control for precise crossover, EQ and limiting functions

* DSP I/O is at 48 kHz and 24 bits, internal processing is 56 bit double-

precision

* Peavey's Quadratic Throat Waveguide™ technology, 100 by 50 degree

coverage

* Asymmetrical horn aims the sound down 10 degrees, at the audience, not

over their heads

* Bluetooth® input is via a dedicated input channel

* Analog input is via a combo female XLR and 1/4” TRS phone jack with

balanced input

* Three channels in total, two for analog, and one for Bluetooth or AUX input via

a 1/8" jack

Loudspeaker System Specifications

* Each channel has a level control and a 3-band EQ section to adjust and

shape the input signals

* Mix/Thru Output is via a male XLR jack

* Durable plastic injection-molded trapezoidal enclosure

* Extra angled section on right side allows floor monitor use

* Full-coverage heavy-duty perforated steel grilles, with powder coat finish

* Pole mount molded-in for 1 3/8” diameter poles

* Top, bottom and right side flying point inserts

Description

The PVX™p 15 Bluetooth® is a two-way sound reinforcement system based on

a heavy-duty Pro 15 15” woofer and a RX14™ titanium diaphragm dynamic

compression driver mounted on a 100 by 50 degree coverage Quadratic Throat

Waveguide™. It’s sleek, modern appearance coupled with excellent

performance, offer a superb overall package.

The lightweight yet rugged injection-molded plastic enclosure with molded-in

stand mount cup facilitates portable use for live music or PA sound. The

trapezoidal cabinet has three handles for ease of portability, and an extra 45-

degree angled section on the right side to allow use as a floor monitor. Five sets

of flying/mounting points, two on the top, two on the bottom, and one on the side,

with a total of 16 cabinet inserts, provide for the ultimate in installation flexibility.

A pair of black powder coated perforated steel grilles provides driver protection

and a professional appearance.

The heavy-duty 15” woofer has a 2 3/8” voice coil diameter, and a 50 oz. magnet

for chest-pounding bass. The RX14™ compression driver tweeter is coupled to

a Quadratic Throat™ constant directivity waveguide. The Quadratic Throat

Waveguide™ is an original Peavey® design, with smooth, even response, low

distortion and good high frequency dispersion. This horn has an asymmetrical

vertical polar response, aiming the main energy lobe down 10 degrees, so it is

aimed at the audience, instead of over their heads. The vertical polar pattern is

+15 degrees, -35 degrees. This helps reduce ceiling reflections for greater clarity

and gain before feedback.

The PVX™p 15 Bluetooth® speaker system power amplifiers providing the bi-

amplification are low-distortion reliable fan-cooled units providing a total of 980W

peak dynamic power for the system.

There is 840 W peak dynamic power for the woofer, and 140 W peak dynamic

power for the tweeter. The power supply for both amps is a switch mode type for

low weight and high efficiency. Both amplifiers feature sophisticated DSP based

signal compression, which virtually eliminates audible power amplifier clipping.

Loudspeaker System Specifications

Cooling is provided via a low-noise fan, for reliable operation under any

conditions.

Input for two of the three input channels is via a combo female XLR and 1/4” TRS

phone jack with balanced input to the preamp/EQ electronics, and a level control.

For these two channels, a switch is provided to change between line level gain

and mic level gain. A third channel is for a Bluetooth® source, or alternatively a

1/8" AUX input jack. Each channel has an adjustable Level control knob, and

also a three-band EQ section that is accessible via the DSP menu Push knob.

There is a balanced output, a Male XLR, that can feed the mixed signals from the

three channels out to another component. This output allows linking of additional

speaker systems, or feed of the signal to a powered subwoofer, etc.

The cabinet of the PVX™p 15 Bluetooth® speaker system has multiple mounting

fly points, providing outstanding versatility in permanent install use. A pair of

M10 inserts is molded-in on the top, and a pair on the bottom, and a set of four

M8 inserts is available on the top, on the bottom, and on the right side in the

handle recess. This is a total of 16 mounting inserts in all. All of these inserts

have retaining hardware on the inside of the plastic cabinet, providing a more

reliable and safe mode of mounting the cabinet.

Applications

The Peavey PVX™p 15 Bluetooth® has a variety of applications such as sound

reinforcement, public address, side fill system, karaoke or musical playback.

The multiple fly points make use as a permanent install system very convenient

with lots of installation flexibility.

A typical signal source for the line-level inputs of the Peavey PVX™p 15

Bluetooth® would be a sound reinforcement mixing console (mixer) or the output

from a CD player, MP3 player or tape deck. The Bluetooth® link provides for

many modern devices to link to the system, such as smart phones, digital mixers,

etc. A typical dynamic microphone can be connected directly via the XLR input

and used as well.

Loudspeaker System Specifications

REAR PANEL

BOTTOM

FUSE (1)

The unit is AC power line fuse protected from overloads and fault conditions with

a slow-blow 5 x 20mm 250V fuse. This fuse is located within the cap of the fuse

enclosure just above the IEC power cord connection. If the fuse fails, THE FUSE

MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO

AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE

WARRANTY!

The fuse in the PVX™p 15 Bluetooth® can be replaced with a time-delay type 5

x 20 mm size 250V rated fuse.

For 100-120VAC operation, a fuse rated at 6.3 amps should be used. In the

USA, types GDC, GMC, 215, 218, and 477 cartridge-style 5 x 20 mm size fuses

with a 6.3 amp 250V rating can be used. The fuse should conform to the

international fuse classification “T6.3AL”.

For the Export model, using an input power voltage range of from 220VAC to

240VAC, use a 3.15 amp rated, 250V 5 x 20 mm cartridge type time-delay fuse,

which conforms to the international fuse classification “T3.15AL”.

If the unit continues to blow replacement fuses, do not keep replacing them- it

should be taken to a qualified service center for repair.

To replace the fuse, be sure to remove the IEC power cord from the IEC socket

(2).

Remove the cap to the fuse enclosure (1) using a flat blade screwdriver tip

inserted into the fuse cap slot. Push the cap in and turn the cap CCW and

Loudspeaker System Specifications

unscrew the cap out until it comes free from the rear portion of the holder. The

blown fuse should come out with the cap.

Remove the blown fuse and replace it with the proper type per instructions

previously supplied. Then, once the new fuse has been put in place, re-insert the

fuse enclosure cap, push in and screw the cap in CW, and make sure it is fully

seated.

Before re-attaching the IEC power cord to the IEC socket, make sure the Power

switch is in the OFF position, so that intermittent contact of the IEC cord while it

is being connected will not unduly stress the amplifier or the fuse.

Now re-attach the IEC power cord, and you can then use the Power switch (3) to

turn the unit on.

IEC POWER CORD CONNECTION (2)

This receptacle is for the IEC line cord (supplied) that provides AC power to the

unit. It is very important that you ensure the PVX™p 15 Bluetooth® has the

proper AC line voltage supplied. You can find the proper voltage for your PVX™p

15 Bluetooth® printed next to the IEC line (power) cord on the rear panel of the

unit.

Please read this guide carefully to ensure your personal safety as well as the

safety of your equipment. Never break off the ground pin on any equipment. It is

provided for your safety. If the outlet used does not have a ground pin, a suitable

grounding adapter should be used and the third wire should be grounded

properly. To prevent the risk of shock or fire hazard, always be sure that the

mixer and all other associated equipment are properly grounded.

ON-OFF SWITCH (3)

This rocker switch supplies AC power to the PVX™p 15 Bluetooth® when

switched to the ON position. The ON position is with the top side of the switch

pushed “in” or nearly flush with the rear panel.

Loudspeaker System Specifications

REAR PANEL

TOP –OPERATING CONTROLS, INPUTS & OUTPUTS

INPUTS (4)

The line-level inputs are of the medium impedance balanced type. For channels

1 and 2 (4a and 4b), the jack is a combo female XLR and 1/4" TRS connector.

For channel 3 (4c), the optional AUX input jack is a 1/8"phone type. Otherwise,

channel 3 is the Bluetooth input channel when the PVX™p 15 Bluetooth® is

linked with a Bluetooth audio device..

Sensitivity of the combo jacks is 0.50 volts for full output, and 0.18 volts for

channel 3 (4c). See the Level Control Adjustment section below for more

details on the input sensitivity with a range of DSP mixer gain settings.

LEVEL (5)

Controls the gain of the preamp or adjusts the level of the input signal. It is used

to directly set the system output level for a given input channel input signal. All

three channels can be mixed together, and made available at the Output jack (7)

MIC/LINE Switch (6)

These control the gain of the Channel 1 (4a) and Channel 2 (4b) to switch from

line level gain to mic gain levels. Gain is increased 40 dB when the switch is in

the MIC position. DO NOT FEED A LINE LEVEL SIGNAL INTO THE INPUT

WITH THE MIC/LINE SWITCH IN THE MIC POSITION! The analog input

circuitry and the DSP system will overload and cause severe distortion that can

not be removed by turning down the Level control !

Loudspeaker System Specifications

OUTPUT jack (7)

This jack is intended for the use of linking multiple PVX™p 15's in a line or to

provide a feed to a powered subwoofer, or other electronics that needs to receive

a full range version of the input signal. The connector is a male XLR jack.

Bluetooth® LED (8)

Illuminates blue when the Bluetooth® channel has been activated. See the

Bluetooth® section for more information.

Push for DSP (9)

This knob accesses the DSP system user control functions, which include a wide

variety of trims and adjustments to the system, and to individual input channels,

etc. See the DSP Menu section for more details.

LCD Screen for DSP Menu (10)

This screen displays the DSP menu options when the Push for DSP knob (9) is

accessed and operated. See the DSP Menu section for more details.

Not shown in the above rear panel diagram is a front baffle LED which can be

switched to OFF, ON (blue) when power is applied, and LIMIT to indicate when

compression and limiting are occurring by flashing RED. This function is

controlled by accessing the DSP system functions via the Push for DSP Knob

(9).

OPERATING INSTRUCTIONS

Cautions

The unit must be disconnected from the AC power source before any

work is done on it. Refer all servicing to qualified service personnel.

The back plate can become hot to the touch. Do not block or cover the fan or the

exhaust louvers from ventilation. There must be a minimum of 4” of space

behind the fan. Do not allow the airflow to be become blocked by objects such

as curtains or drapes, thermal building insulation, etc. It is recommended that

the rear of the PVX™p 15 Bluetooth® not be placed in a closed space or a space

that has no fresh, cool airflow.

Be sure to keep the microphone away from the front of the speaker after

connecting it to the input, and while setting the microphone level, or very loud

feedback will occur! Damage to the system is likely if this occurs!

Loudspeaker System Specifications

DO NOT connect the inputs of the PVX™p 15 Bluetooth® to the output of

a power amplifier. The inputs are meant to be driven from a line-level strength

signal.

DO NOT remove the protective metal grilles.

WARNING! The PVX™p 15 Bluetooth® is very efficient and powerful! This

sound system can permanently damage hearing! Use extreme care setting the

overall maximum loudness!

The apparent sound level of the PVX™p 15 Bluetooth® can be deceiving due to

its clear, clean sound output. The lack of distortion or obvious distress can make

the sound level seem much lower than it actually is. This system is capable of

SPL in excess of 127 dB at 1 M from the speaker!

Flying the PVXp™15

IMPORTANT SAFETY INFORMATION FOR THE MOUNTING AND FLYING OF

THE PEAVEY PVX™p 15

CAUTION: Before attempting to suspend this speaker, consult a certified

structural engineer. Speaker can fall from improper suspension, resulting in

serious injury and property damage. Other enclosures may NOT be suspended

below one, nor should additional weight be suspended from one of these units.

Use only the correct mating hardware. All associated rigging is the responsibility

of others.

Maximum enclosure angle from vertical hang is 30 degrees.

Always use a suitable safety chain or wire rope, attached to an unused group of

fly points or to the cabinet as directed by a certified structural engineer, and firmly

attached to a suitable structural member as indicated by a certified structural

engineer.

The recommended range of torque for the mounting bolts is 3.5 to 4.0 foot-lbs.

(4.75 to 5.42 N-m). DO NOT OVERTIGHTEN ! If an insert spins free, it has

been damaged, and the cabinet can not be safely flown from that set of inserts!

Never transport the cabinet while mounted on an array bracket or other mounting

bracket, this may unduly stress the mounting inserts.

The use of threadlocker (blue type/medium strength) on the mounting bolts is

recommended, as are the appropriate lockwashers, to insure that the mounting

hardware will not vibrate loose over time.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Peavey Sprecher Handbücher

Peavey

Peavey Scorpion Series S 10425 Bedienungsanleitung

Peavey

Peavey 115 Ti Bedienungsanleitung

Peavey

Peavey Scorpion S 12825 Systemhandbuch

Peavey

Peavey PR 12 D Bedienungsanleitung

Peavey

Peavey SP 1G Bedienungsanleitung

Peavey

Peavey HDH-2 Bedienungsanleitung

Peavey

Peavey Impulse Impulse 2652 Bedienungsanleitung

Peavey

Peavey p2 Bedienungsanleitung

Peavey

Peavey Impulse Impulse 6 Bedienungsanleitung

Peavey

Peavey Pro Rider Bedienungsanleitung

Peavey

Peavey PVXp 10 Bedienungsanleitung

Peavey

Peavey SP 115MX Bedienungsanleitung

Peavey

Peavey TLS 1X Bedienungsanleitung

Peavey

Peavey PR 15 Bedienungsanleitung

Peavey

Peavey Sanctuary Series SSE UB2T Bedienungsanleitung

Peavey

Peavey HDH M Bedienungsanleitung

Peavey

Peavey Versarray 212 Bedienungsanleitung

Peavey

Peavey Scorpion Ultra 12 Bedienungsanleitung

Peavey

Peavey SheffieldPro 1200 Bedienungsanleitung

Peavey

Peavey 112 DLM Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Peavey

Peavey A/A Series Bedienungsanleitung

Peavey

Peavey Tri-Flex Bedienungsanleitung

Peavey

Peavey WFS 3.70 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung

Tannoy

Tannoy SYSTEM 600a Bedienungsanleitung