Peco 12007HD Bedienungsanleitung

OWNER’S MANUAL

MODEL 12006 & 12007HD

(Q0080)

THE ORIGINAL

PECO POWER SPRAYER

PECOPECOPECOPECOPECOPECO

PPP

PECOPECOPECOPECOPECOPECOPECO

Revision: 4 - 6/27/2016

PECO POWER SPRAYER

MODEL 12006 & 12007HD

TABLE OF CONTENTS

Introduction

Thank you for purchasing the original PECO Power Sprayer. Your new PECO sprayer has been

engineered and manufactured to PECO’S high standards for safety, quality, dependability and ease

of operation. Our sprayer eliminates pumping or lugging a heavy tank on your back.

Features

— Self-contained 12-volt electric sprayer

—14” wheels and light-weight aluminum cart make

it easy to maneuver over lawn and garden surfaces

— Electric pump runs up to 5 hours on a single charge

—Removable wide-mouth five gallon container makes mixing liquids easy

—Spray adjusts from a fine mist to a 30 foot stream

SECTION PAGE

INTRODUCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

FEATURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

DESCRIPTION- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3

PARTS AND SERVICE - - - - - - - - - - - - - - - - - - - - - - - - - 4

ASSEMBLY INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - - 5

OPERATION INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - 6

BATTERY INFORMATION - - - - - - - - - - - - - - - - - - - - - - - 6

SECTION PAGE

SPRAYER CARE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6

STORAGE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6

RETURNING PUMP/MOTOR FOR SERVICE - - - - - - - - - - 7

POWER SPRAYER PARTS LIST - - - - - - - - - - - - - - - - - - 8

EXPLODED PARTS VIEW - - - - - - - - - - - - - - - - - - - - - - - 9

SPRAYER WIRING DIAGRAM - - - - - - - - - - - - - - - - - - - - 10

SPRAYER WIRING KIT - - - - - - - - - - - - - - - - - - - - - - - - - 11

PECO LIMITED WARRANTY - - - - - - - - - - - - - - - - - - - - - 12

DESCRIPTION

MODEL 12006 & 12007HD

THE PECO POWER SPRAYER

HANDLE

SPRAY WAND HOSE

WAND MOUNT

BRACKET

5 GALLON

CONTAINER

POWER

ON/OFF

BATTERY

CHARGER

RECEPTACLE

SERIAL

PLATE

PARTS AND SERVICE INFORMATION

PECO Power Sprayer owners should record the name and telephone number of their Service Center. Your Service

Center will be happy to supply replacement parts, accessories, and do any service or repairs to your PECO Power

Sprayer. If for any reason your Service Center is unable to service your PECO Power Sprayer or supply replacement

parts, contact PECO and include the following information on the chart below.

Unit Model Number:_________________________________

Unit Engine Size: __________________________________

Unit Serial Number: _______________________________

Date of purchase: _____/_____/_________

Dealer/Distributor Name: _________________________________________

Address: ___________________________________ State:___________ Zip:____________

Phone Number: ____________________________

Address: New PECO, Inc.

10 Walden, Drive

Arden, NC 28704

Phone #: (828) 684-1234 or Toll Free: (800) 438-5823

Email: peco@lawnvac.com

Model Number

Serial Number

PECO

OUTDOOR POWER EQUIPMENT

Arden, North Carolina 28704

ASSEMBLY INSTRUCTIONS

Step 1. Remove contents from shipping container.

(Power Sprayer, Handle, and Manual)

Step 2. Remove the hardware from the handle.

Insert the handle into the frame. Fasten the

handle to the frame using (2) 1/4”-20 x 1”

pan head machine screws P#(K0601) and

(2) 1/4”-20 hex nuts P#(K1124) previously removed.

INSERT HANDLE HERE

AND FASTEN TO THE FRAME

(2) 1/4”-20 x 1” PAN HEAD

MACHINE SCREWS P#(K0601)

AND (2) 1/4-20 HEX NUTS

P#(K1124)

OPERATION INSTRUCTIONS

After flipping the switch into the ON position, squeeze wand handle to allow air pressure in

hose to be released (make sure the strainer is completely submerged). Hold wand handle until

liquid begins to flow and all air bubbles are out of the hose. To adjust the spray into a stream,

turn the nozzle tip counter-clockwise. To adjust the spray into a fine mist, turn the nozzle tip

clockwise. Always turn the sprayer off before re-filling the container. Be sure to loosen or

remove the vent cap from the smaller tank opening to avoid creation of a vacuum inside of tank.

BATTERY & CHARGER INFORMATION

Initial Charger Setup: Using a Phillips screwdriver, loosen each screw, positive(+) &

negative(-), located on charger (Item #48, Page 10). Next, attach red positive(+) & black

negative(-) leads of charger harness (Item #49, Page 10) to corresponding red positive(+) &

black negative(-) screw on charger. Tighten screws to securely fasten leads.

Fully Charge Before First-Time Usage: Plug charger into wall socket and plug opposite

connecting end into sprayer to begin battery charging. Notice a “Green” & “Red” light located

on charger. Once correctly plugged in, a steady “Red” light designates battery charging and a

steady “Green” light designates battery charged. Leave charger connected until a steady

“Green” light is achieved before using sprayer.

The new battery charging system eliminates user error and will automatically stop charging

once detecting battery is fully charged. Battery charging time will vary depending on power

level remaining in battery. Once fully charged, the battery will last up to 5 hours before needing

to be re-charged. Only use charger provided to prevent overheating and any permanent damage

to the battery. The battery life span is around 200 charges.

SPRAYER CARE

Immediate cleaning and proper maintenance after each use will eliminate most sprayer failures.

This sprayer is made of the most chemical resistant materials available, but care must be taken

to ensure a long life. Many chemicals can deteriorate pump parts if not rinsed clean after each

use. Which solution you use will depend on the pesticides used. Always check the pesticide

label for cleaning instructions. Clean pump thoroughly with a cleaning solution for 3 minutes.

Rinse with clean soapy water for 2 minutes to remove cleaning solution. DO NOT USE BLEACH

SOLUTION OR HIGHLY FLAMMABLE LIQUIDS SUCH AS GASOLINE OR PAINT THINNER IN

SPRAYER. Soluble powders and diluted liquids may be used in the sprayer. Wet powder

solutions tend to come out of solution, coating the inside of the pump. Wet powders must be

washed out very thoroughly. Over a period of time, most chemicals will separate and a build up

in the pump. Chemicals are absorbed by plastic hoses and cannot be rinsed out after extended

periods of time. Rinse thoroughly after each use.

STORAGE

Special care should be taken before storage of the sprayer. Fully re-charge the battery.

Thoroughly rinse the pump, hoses and container with clean, soapy water.

RETURNING PUMP/MOTOR ASSEMBLY FOR

WARRANTY OR REPLACEMENT PURCHASE

DO NOT ATTEMPT TO DISASSEMBLE THE PUMP. Internal parts are spring

loaded and may be lost or damaged.

REMOVE THE PUMP AND MOTOR AS AN ASSEMBLY AS FOLLOWS:

1. Remove the pump lid by removing two screws shown.

2. Remove the hoses from the sprayer pump.

3. Remove the four bolts that hold pump/motor in box.

4. Disconnect the red and black wires.

5. Remove the pump/motor from the pump box.

For Warranty:

Call 1-800-438-5823 to receive a Return Authorization before sending your pump back for

service. (In N.C. call 828-684-1234)

Box your pump and motor assembly up and place the Return Authorization on the outside of the

box and return VIA United Parcel Service, (not US Mail) to the following address:

New PECO, Inc.

10 Walden Drive

Arden, NC 28704

Failure to follow the above instructions may delay the inspection/replacement of your pump

REMOVE BOLTS REMOVE BOLTS

REMOVE

REMOVE HOSES

PECO POWER SPRAYER PARTS LIST

REF NO. PART NO. DESCRIPTION QTY

01 C1173 SPRAYER MAIN FRAME BOX 01

02 C1175 SPRAYER BATTERY BOX 01

03 C1174 FRONT KICK PLATE 01

04 C0057 WAND MOUNT BRACKET 01

05 C1176 BATTERY BOX LID 01

06 B3182 SPRAYER HANDLE 01

07 B3183 AXLE LEG SUPPORTS 02

08 B0738 UPPER WAND HOSE HANGER 01

09 B0596 LOWER WAND HOSE HANGER 01

10 B4176 SPRAYER AXLE 1/2” x 16 1/4” 01

11 H4001 SPRAYER WHEEL 02

12 F4001 30 IN. HOSE 01

13 F4005 POWER SPRAYER HOSE 96 IN. 01

14 S0301 5 GALLON TANK 01

15 S0302 SPRAYER CAP LARGE 01

16 V0038 3/4” ID RUBBER GROMMET 02

17 V1022 HOSE ADAPTER 01

18 V0029 1” NEOPRENE SEAL / 5” LONG 06

19 J1301 SPRAYER WAND EXT. 18” 01

P0231 (12007HD) POLY SPRAYER WAND 18” 01

20 J1302 SPRAYER WAND EXT. 36” 01

21 J1310 WAND NOZZLE 01

P0229 (12007HD) POLY WAND NOZZLE 01

22 J1320 WAND HANDLE 01

P0230 (12007HD) POLY WAND HANDLE 01

23* J1201 SPRAYER BATTERY 01

24* J2001 TOGGLE SWITCH FOR SPRAYER 01

25* J2004 ON-OFF FACE PLATE 01

26* J2005 15/32”-32 HEX PANEL NUT 01

27 J1309 MESH STRAINER 01

29 J0129 THREADED HOSE CLAMP 04

30 K0028 TINNERMAN CLIP #14-20 04

31 K0029 TINNERMAN NUT 04

32 K0055 1/2” FLAT WASHER 04

33 K0068 TINNERMAN CLIP 02

34 K0200 1/2” PUSH NUT 02

35 K0601 PAN HEAD MACHINE SCREW 06

36 K1092 TINNERMAN SCREW 3/4” 04

37 K1096 TINNERMAN SCREW 1/2” 06

38 K1124 HEX HEAD NUT 1/4”-20 04

39 K1128 1/4”-20 NYLOC NUT 12

40 R4040 4.5” x 3” SPRAYER CARE DECAL 01

41 R1603 SERIAL NUMBER PLATE 01

42 R4027 PECO MADE IN THE U.S.A. LABEL 01

43 R4007 BATTERY CHARGE TIME LABEL 01

44 R1103 ORIGINAL POWER SPRAYER LABEL 03

46* P0210 ELECTRIC SPRAYER PUMP 01

P0228 (12007HD) FLOJET ELECTRIC SPRAYER PUMP 01

47* P0211 SPRAYER CHARGER PORT 01

48* P0212 12V SPRAYER CHARGER 01

49* P0213 SPRAYER CHARGER WIRE 72” 01

50* P0232 WIRE HARNESS (+) 01

51* P0233 WIRE HARNESS (-) 01

*See Page 10 & 11 for Electrical Wiring Diagram ** 12007HD Contains All Same Parts Except Where Noted

Power Sprayer Exploded Parts View

23 10

Sprayer Wiring Diagram

Short Post - Red Wire (+)

Medium Post - Black Wire (-)

Long Post - Not Used

Red Pump Wire (+) to

On/Oﬀ Switch Top

Terminal

Black Pump Wire (-) to

P0233 Harness

(50)

P0232 Harness

(51)

P0233 Harness

(46)

(49)

(48)

Ref. # Part # Description Qty

23 J1201 SPRAYER BATTERY 01

24 J2001 TOGGLE SWITCH FOR SPRAYER 01

25 J2004 ON-OFF FACE PLATE 01

26 J2005 15/32”-32 HEX PANEL NUT 01

46 P0210 ELECTRIC SPRAYER PUMP 01

P0228 (12007HD) FLOWJET ELECTRIC SPRAYER PUMP 01

47 P0211 SPRAYER CHARGER PORT 01

48 P0212 12V CHARGER 01

49 P0213 CHARGER HARNESS (72” Long) 01

50 P0232 WIRE HARNESS (+) 01

51 P0233 WIRE HARNESS (-) 01

(24)(25)(26)

(47)

(23)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Peco Spritzpistole Handbücher

Peco

Peco PS5 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung