Peerless-AV IBA2 Leitfaden

Installation and Assembly:

Recessed Cable Management and Power Storage

Accessory Box

Models: IBA2, IBA2-W

ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

2 of 6 ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112

Note: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Metal Stud Do not attach except with Peerless accessory kit ACC415;

Contact Customer Service for Peerless accessory kit ACC415

•Brick Contact Qualiﬁed Professional

•Drywall Do not attach except with Peerless accessory kit ACC415;

Contact Customer Service for Peerless accessory kit ACC415

•Other or unsure? Contact Qualiﬁed Professional

WARNING

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Wall ........................................................................................................................................................4

Cable Management ................................................................................................................................................................5

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 3/16" (5mm) drill bit for wood studs

• level

3 of 6 ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

IBA2 IBA2-

Description Qty. Part # Part #

in-wall box 1 120-P1185 120-2185

B1-1/2" wood screw 4 500-1090 500-4090

C4mm security driver 1 560-1133 560-1133

Dcable bushing 1 590-1295 590-2295

Ecable management clips 2 590-1166 590-1166

Fplastic finishing cap 1 590-1123 590-2123

Gcable tie 2 590-1168 590-1168

Haccess plate 1 120-P1187 120-2187

IM5 x 6mm phillips screw 5 520-1023 520-2214

Parts List

4 of 6 ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112

In-wall box (A) can be installed between two studs

16" off center. Use a stud ﬁnder to locate the

edges of the studs. Use of an edge-to-edge stud

ﬁnder is highly recommended. Based on its edges,

draw two vertical lines down the inside edges of

the studs. Mark desired center of in-wall box. Draw

a horizontal line 4-15/16" (125mm) above desired

center of in-wall box. Draw a second horizontal

line 9-3/4" (247mm) below this line to outline wall

opening between inside edges of studs. Remove

drywall inside cut outline.

Insert in-wall box (A) into wall until ﬂange is ﬂush

with drywall as shown in ﬁg. 1.1.

Level in-wall box, and mark center of the four

mounting holes. Make sure that the mounting

holes are on stud centerlines. Drill four 3/16"

(5mm) dia. holes 1-1/2" (38mm) deep. Make sure

in-wall box is level, and secure it using four wood

screws (B) as shown in ﬁg. 1.2.

Installation to Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that in-wall box is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

9-3/4"

(247mm)

13-1/8"

(333mm)

ﬁg. 1.1

STUDS

FLANGE

TOP LINE OF CUT

OUTLINE

CENTER OF

IN-WALL BOX

4-15/16"

(125mm)

ﬁg. 1.2

5 of 6 ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112

Attach access plate (H) to in-wall box (A) with ﬁve M5 x 6mm phillips screws (I) as shown in ﬁgure 2.1. Access

plate knockout may be removed for optional installation of electrical gang box.

Insert up to two cable management clips (E) into the desired positions in the in-wall box as shown in ﬁgure 2.2 for

routing cables.

Insert cable bushing (D) into in-wall box for routing cables through in-wall box. Plastic ﬁnishing cap (F) may also

be used if cable management is unnecessary.

Use cable ties (G) to secure cables to cable management clips as shown in ﬁgure 2.3.

Cable Management

D or F G

CABLES

ﬁg. 2.2 ﬁg. 2.3

ﬁg. 2.1

All other brand and product names are trademarks or registered trademarks of their respective owners.

ACCESS PLATE

KNOCKOUT

6 of 6 ISSUED: 12-27-10 SHEET #: 120-9098-2 06-13-11

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112

Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal

use, for a period of ﬁve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).

At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.

In no event shall the duration of any implied warranty of merchantability or ﬁtness for a particular purpose be longer than the period of the applicable

express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,

(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,

using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.

In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured

by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other

person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.