Peerless-AV WL-AU-AVWS Leitfaden

ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Installation and Assembly:

PeerSound™ Wireless AV Wall System

PeerSound™ Wireless Audio Wall System

Models: WL-AU-AVWS, WL-AU-AVWS-W, WL-AU-AVWSA, WL-AU-AVWSA-W

3ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List................................................................................................................................................ 4

Installation to Double Stud Wall............................................................................................................. 6

Installation to Metal Stud Wall ...............................................................................................................8

Installation to Solid Concrete or Cinder Block......................................................................................10

Component Connections......................................................................................................................17

Ampliﬁer................................................................................................................................................18

Ampliﬁer Setup......................................................................................................................................19

Wireless Microphone Setup...................................................................................................................19

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

•phillips screwdriver

• drill

• 3/8" bit for solid concrete surface

• 3/16" bit for wood studs

• 1/2" bit for metal studs

• socket wrench

• 7/16" socket

• level

• hammer

• Pencil

• Tape Measure

• Do not begin to install your Peerless product until you have read and understood the instructions

and warnings contained in this Installation Sheet. If you have any questions regarding any of the

instructions or warnings, for US customers please call Peerless customer care at

1-800-865-2112, for all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience

with basic building construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and

all attached hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood joists ceilings, make sure that mounting screws are anchored into the center

of the studs. Use of an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly

reducing their holding power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product

failure and personal injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

•Wood Stud Included

• Wood Joist Included

• Solid Concrete Included

• Metal Stud Included (Not Evaluated By UL)

• Brick Contact Qualiﬁed Professional (Not Evaluated By UL)

• Other or unsure? Contact Qualiﬁed Professional

WARNING

4ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Before beginning, make sure you have all parts shown below.

EFH

JK L M

Parts List WL-AU-AVWS WL-AU-AVWS-W WL-AU-AVWSA WL-AU-AVWSA-W

Description Qty. Part # Part # Part # Part #

Aenclosure assembly 1 180-1201 180-2201 180-1201 180-2201

B10mm concrete anchor 4 590-0321 590-0321 590-0321 590-0321

C5/16" x 3" wood screw 4 520-1243 520-1243 520-1243 520-1243

Dpower strip 1 600-0100 600-0100 600-0100 600-0100

Ereceiver bracket assembly 1 180-1190 180-2190 — —

Famp bracket 2 180-1173 180-2173 180-1173 180-2173

Gmic bracket 1 180-1189 180-2189 180-1189 180-2189

Hcover assembly 1 180-1200 180-2200 180-1200 180-2200

Im5 x 6mm security screw 8 520-1114 520-2062 520-1114 520-2062

Jcable bushing 2 590-1295 590-2295 590-1295 590-2295

Kfinishing cap 2 590-1123 590-2123 590-1123 590-2123

Lcable tie anchor 3 600-0101 600-0101 600-0101 600-0101

Mcable tie 3 560-9711 560-9711 560-9711 560-9711

N4mm security allen wrench 1560-9646 560-9646 560-9646 560-9646

Otoggler 4 560-9708 560-9708 560-9708 560-9708

P1/4"-20 x 2.5 phillips screw 4 520-9521 520-9521 520-9521 520-9521

Qm5 x 6mm serrated washer head security screw 6 510-1114 510-1114 510-1114 510-1114

Rm4 x 10mm serrated washer head security screw 2 510-1060 510-1060 510-1060 510-1060

5ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

AA BB

KK LL

MM NN

CC DD EE FF GG

HH II JJ

AUDIO-REMOTE

Parts List WL-AU-AVWS WL-AU-AVWS-W WL-AU-AVWSA WL-AU-AVWSA-W

Description Qty. Part # Part # Part # Part #

AA wireless transmitter hds-200 1180-1002 180-1002 — —

BB wireless reciever hds-200 1180-1003 180-1003 — —

CC power adapter - 12v 2a 2180-1004 180-1004 — —

DD plastic stand for hds-200 2180-1005 180-1005 — —

EE vga to rca adapter for hds-200 1180-1006 180-1006 — —

FF remote controller for hds-200 1180-1007 180-1007 — —

GG battery cr2025 3v 1180-0008 180-0008 — —

HH ir flasher 1180-1009 180-1009 — —

II ir-extender gen-2 1180-0029 180-0029 — —

JJ amplifier, 25x2 - 2 input 1180-1085 180-1085 180-1085 180-1085

KK amp kit 50w ac to dc power adapter 24v-2a 1180-1088 180-1088 180-1088 180-1088

LL amp kit 50w ir extender eye, oval with tape 1180-1089 180-1089 180-1089 180-1089

MM amp kit 50w card remote with battery 1180-1090 180-1090 180-1090 180-1090

NN 3.5 audio cable 1180-0192 180-0192 — —

6ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Use a stud ﬁnder to locate the edges of the studs and draw a vertical line down the center of

each stud. Place enclosure assembly (A) on wall. Level enclosure and mark center of four

mounting holes making sure that the mounting holes are on the stud centerlines. Drill four

3/16" (5mm) dia. pilot holes to a depth of 3" (76 mm). Insert two screws (C), leaving a 1/2" gap

between the screw head and the wall, as shown in ﬁg. 2.1.

ﬁg. 2.1

Installation to Double-Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the

equipment and all attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening

can damage the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to

edge" stud ﬁnder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into

wood studs. Installers are responsible to provide hardware for other types of mounting situations

(not evaluated by UL).

WARNING

C1/2"

(13mm)

Skip to page 8 for Metal Stud Installation.

Skip to page 10 for Concrete and Cinder Block Installation.

7ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Position enclosure on wall. Install remaining two screws (C). Level enclosure assembly (A) and

tighten all screws.

Using the keyholes in the back of enclosure assembly (A), place enclosure assembly (A) on

to the two screws (C). Slide enclosure assembly (A) over until the mark on the wall plate lines

up with the center of the screw (C) as shown in detail A. NOTE: When mounting on 16" stud

centers, use bottom set of slots. For 20" and 24" stud centers, use top set of slots.

KEYHOLE

ﬁg. 2.2

ﬁg. 2.3

DETAIL A

8ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Use a stud ﬁnder to locate the edges of the studs and draw a vertical line down the center of

each stud. Place enclosure assembly (A) on wall. Level enclosure and mark center of four

mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 1/2"

(13mm) dia. holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32"

pilot holes prior to drilling 1/2" holes. Insert togglers (O) as shown in ﬁgure 2.4. Insert two 1/4"-

20 x 2.5" phillips screws (P), leaving a 1/2" gap between the screw head and the wall, as shown

in ﬁg. 2.5.

Installation to Metal Stud Wall

• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or heavier.

• Installer must verify that the supporting surface will safely support the combined load of the

equipment and all attached hardware and components (Not Evaluated By UL).

WARNING

• Product must be mounted through drywall

that has a minimum thickness of 1/2" and

into metal studs, 24 gauge or heavier.

• Make sure that togglers are anchored into

the center of the studs as shown in ﬁgure

2.2. The use of an "edge to edge" stud

ﬁnder is highly recommended.

• This product is intended for indoor use only.

Use of this product outdoors could lead to

product failure and personal injury.

WARNING

ﬁg. 2.4

ﬁg. 2.5

1/2"

(13mm)

Pivot end of toggler (O).

Push into hole.

Rotate toggler (O) clockwise to wedge it against inside walls

of metal stud.

Slide plastic cap forward while pulling back ﬁrmly on ring.

Break off excess.

9ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Using the keyholes in the back of enclosure assembly (A), place enclosure assembly (A) on to

the two 1/4"20 x 2.5" phillips screws (P) as shown in ﬁg. 2.6. Slide enclosure assembly (A) over

until the mark on the wall plate lines up with the center of the 1/4"20 x 2.5" phillips screws (P) as

shown in detail B. NOTE: When mounting on 16" stud centers, use bottom set of slots. For 20"

and 24" stud centers, use top set of slots.

KEYHOLE

ﬁg. 2.6

ﬁg. 2.7

DETAIL B

1Position enclosure on wall. Install remaining two 1/4"20 x 2.5" phillips screws (P). Level

enclosure assembly (A) and tighten all screws.

10 ISSUED: 2012-10-11 SHEET #: 180-9041-2 2012-05-31

Place enclosure assembly (A) on wall and

mark center of four mounting holes. Drill

four 3/8" (10 mm) dia. pilot holes to a depth

of 3" (76 mm). Insert anchors (B) into holes

ﬂush with wall as shown (right). Insert two

screws (C), leaving a 1/2" gap between the

screw head and the wall, as shown in ﬁg.

2.8.

Drill holes and insert anchors (B).

Place enclosure (A) over anchors (B) and secure with screws

(C).

Tighten all fasteners.

concrete

surface

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of

1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors.

Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25

mm) minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁcations.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete

anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment

and all attached hardware and components.

• Tighten screws so that wall plate is

ﬁrmly attached, but do not overtighten.

Overtightening can damage screws,

greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9

N.M.).

• Always attach concrete expansion

anchors directly to load-bearing concrete.

• Never attach concrete expansion anchors

to concrete covered with plaster, drywall,

or other ﬁnishing material. If mounting to

concrete surfaces covered with a ﬁnishing

surface is unavoidable (not evaluated

by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure

concrete anchors do not pull away from

concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16

mm), custom fasteners must be supplied

by installer (not evaluated by UL).

WARNING

Installation to Solid Concrete or Cinder Block

1/2"

(13mm)

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

ﬁg. 2.8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere peerless-AV Projektor Handbücher

peerless-AV

peerless-AV PSTA-1200 Leitfaden

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung

peerless-AV WL-AU-AVWS Leitfaden

Beliebte Projektor Handbücher anderer Marken