Peerless-AV PeerSound ADS100-B Bedienungsanleitung

ISSUED: 08-30-13 SHEET #: 180-9051-1

User Manual and Installation Guide

Models:

ADS100-B

Wireless Audio System

2 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Contents

Important Safety Instructions......................................................................................................... 3

Important Information..................................................................................................................... 4

Unit Care Recommendations ......................................................................................................... 4

Speciﬁcations.................................................................................................................................. 5

Introduction...................................................................................................................................... 6

What’s In The ADS100-B Box ........................................................................................................... 6

Tools Needed For Installation........................................................................................................ 6

Installation Planning ...................................................................................................................... 6

Installation........................................................................................................................................ 7

Product Overview .......................................................................................................................... 7

Transmitter: Mounting.................................................................................................................... 9

Transmitter: Power Connections ................................................................................................... 9

Transmitter: Antenna And Cable Connections............................................................................... 9

Transmitter: TX Module Connections .......................................................................................... 10

Transmitter: Input Signal Connection - Speaker Level Option .................................................... 10

Transmitter: Input Signal Connection - Line Level Audio Option................................................. 10

In-Wall Installation of the ADS100-A252 Wireless Receiver/Ampliﬁer .........................................11

Transmitter and Ampliﬁer Pairing ................................................................................................ 12

Stereo vs Mono Setup................................................................................................................. 12

Multiple Ampliﬁers to Same Inputs .............................................................................................. 12

Power Outages............................................................................................................................ 12

Finalizing The Installation ............................................................................................................ 13

FAQs............................................................................................................................................... 14

Limited Warranty ........................................................................................................................... 15

3 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Important Safety Instructions

Warnings/Safety

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt

into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with

the apparatus.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15. The product was submitted and evaluated for use at the maximum ambient (Tma)ἁ40°C

16. WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To

Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus..

CAUTION

RISK OF ELECTRIC SHOCK!

DO NOT OPEN!

ATTENTION ! RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR !

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated dangerous voltage within the product's enclosure

that may be a sufﬁcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

Le symbole de l'éclair avec une ﬂèche à son extrémité, dans un triangle équilatéral, a pour

but de vous avertir de la présence d'une « tension électrique dangereuse » et non isolée à

l'intérieur de l'enceinte de l'appareil, qui peut être sufﬁsamment puissante pour constituer

un risque d'élctrocution pour les personnes

Le point d'excalamation dans un triangle équilatéral vous avertit de l'existence d'instructions

importantes de fonctionnement et d'entretien (intervention) dans la documnetation

accompagnant l'appareil.

4 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Model:ADS100-A252

FCC ID: 2AAW2ADS100-A252

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Model:ADS100-T8

FCC ID: 2AAW2ADS100-T8

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

17. Avoid overloading electrical outlets or extension cords which otherwise could result in electric

shock or ﬁre.

18. To avoid electric shock, never stick anything in the slots on the case or remove the cover.

19. This product is intended for indoor use only.

20. The apparatus shall be connected to a mains socket outlet with a protective earthing connection.

Important Information

• Never use this product in an aircraft or a medical facility. It can cause interference or an

undesirable effect.

• The use of this product in the following locations may result in an abnormal audio output (noise,

etc,).

º Near a refrigerator or metal structure.

º In a cluttered room, causing potential blocked wireless signals.

• This product has been tested and manufactured to comply with each country’s safety rules.

However, there is no guarantee that interference will not occur in some installations. If

interference happens, decrease the distance between the product and receiving antenna.

• Optimal use of this product is for in-room/multi-room applications with a range of up to 140 ft.

(43m) away line-of-sight (LOS). This distance is reduced slightly when objects like walls and

ﬂoors are in the transmission path.

• Any changes or modiﬁcations not expressly approved by the manufacturer of this device could

void the product warranty.

• This equipment must be installed and operated in accordance with the provided instructions.

End users and installers must be provided with installation instructions and Transmitter operating

conditions for satisfying RF exposure compliance.

• This device should be used only as speciﬁed within this manual to meet RF exposure

requirements. Use of this device in a manner inconsistent with this manual could lead to

excessive RF exposure conditions.

Unit Care Recommendations

To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they may cause

electrical failure or damage the surface of the product.

5 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

SPECIFICATIONS

T8 Transmitter

• Size: 17 ¼”w x 1 11/32” h x 7”d

• Rack Height: 1U

• Power Input: 120/240 VAC 50/60Hz to supplied AC adapter (5VDC @ 1000 mW)

• Line Level Inputs: Qty 8 independent RCA

• Speaker Level Inputs: Qty 8 independent, 150 watts max each, 2 pole plug

• Mounting: Rack or surface

• Frequency band: 2.4 GHz, spread spectrum

• Wireless distance: 140 ft*

• Streaming: 16 Bit, 48 KHz rate with error checking

• Adaptive Frequency Hopping:Yes, 18 channels with 4 active, 14 on trial

• Latency: 42.7 mS

• Antenna cable: RG316D Coax, double shield with reverse thread ﬁttings, 10 ft.

• Agency Approvals: UL60065, CE, LVD, FCC

* Actual distance will be reduced with obstructions between transmitter and receiver modules

A252 Ampliﬁer

• Size: 4”h x 4 1/8”w x 1 ½”d

• Power Input: 100/240 VAC 50/60Hz direct, 150 watts maximum (with protective

ground required)

• Power Connection: 2 wire spring hold push in, screw terminal ground, wired or conduit per

Electric Code

• Speaker Connection: Qty 2 – 2 pole screw clamp plug

• Impedance: 8 ohm

• Power Output: 25 watts x 2 @ <0.1% THD+N(1 W, 1KHz)

• Signal to Noise: 110 dB

• Protection: Over temperature, overload, short circuit, with power cycle reset

• Mounting: In-wall, On-wall, UL 2043 Plenum area’s (with proper UL 2043

accessories)

• Agency Approvals: UL60065, UL 2043, CE, LVD, FCC

6 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Introduction

The Peer Sound Wireless Audio System provides for eight total independent channels, four total

stereo zones or any combination in-between. By connecting your source(s) to either the RCA line

level or speaker level inputs, you can wirelessly transmit the audio signal and amplify it for the remote

speakers. This system works with any brand speakers or sources (ampliﬁer or preamp).

The installation process starts with a little planning and understanding the options you have for

installation.

(1) ADS100-T8 Transmitter Kit

• (1) pair of rack ears + Screws

• (1) ADS100-TX14 TX Module Kit

• SCR M2x.4 x 4MM PAN HD PHL BLK

• (1) ADS100-A252 Ampliﬁer Kit

• In-wall holder for amp

• In-wall bracket screw for amp

• (2) Drywall clamp w/ screws

• (1) Conduit adapter bracket

• (1) 2 Gang oversize wall plate w/ screws

• (1) ADS100-RXS RX Stereo Module Kit

• SCR M2x.4 x 4MM PAN HD PHL BLK

• (1) ADS100-RAC10 TX Remote Cable Kit

• TX remote cable, 10'

• In-wall amp template

• Antenna remote mount bracket

• System instructions

Tools Needed For Installation

• Bubble Level

• Phillips Screwdriver

• Small straight screwdriver

• Drywall Saw

• Wire Strippers

• Side Cutters

• Tape Measure

• Pencil

Installation Planning

There is ﬂexibility in the component installations.

First: Options for the transmitter:

• Place unit on a ﬂat surface (like cabinet)

• Place unit inside a standard AV rack assembly

• Local or remote antenna mounting options. A 10ft thin coax cable is provided for remote

antenna mounting. The cable has a bulkhead ﬁtting that allows for 0.10” (2.54mm) thickness.

Second: Flexible ampliﬁer/receiver installation options:

• Inside a drywall cavity (ﬂush to the outer surface). The maximum drywall thickness is 5/8”.

• Attached to a structure, such as ceiling beams

• On top of a wall surface (requires accessory kit ADS100-OWK)

• In a UL 2043 plenum area (requires UL 2043 plenum wiring, tie wraps, etc)

It helps to have your ampliﬁer locations in mind when starting the installation process. Generally, the

ampliﬁer is placed near a 120/240 VAC power source, capable of 150 watts peak demand.

Tip: While this device does not require Line-of-Sight, the signal can still be effected by certain building materials. For

best wireless performance, try to keep cement or a lot of steel (like ductwork or a refrigerator) out of the imaginary

line-of-sight between transmitter and receivers.

What’s In The ADS100-B Box

Before you start the installation, make sure you have the following items:

7 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Installation

Product Overview

Front

1. POWER

• Turns unit ON/OFF

2. SYNC 1-4

• Used to pair amps for channels 1-4

3. SYNC 5-8

• Used to pair amps for channels 5-8

Back

1. Transmitter Module

• Sends signal to RX on amp

2. RCA Line Level Input (8)

• Inputs for AV component connection

3. Speaker Level Input

• Inputs for AV speaker connection

4. Transmitter Module Plug

• Accepts Transmitter Module

5. DC POWER

• Power input

123

123 54

8 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Installation

Product Overview

Front

1. RX MODULE

• Insert RXS or RXM Module here

2. POWER INDICATOR

• Blue when power is on.

Back

1. Power Connector

2. Ground Connector

3. Speaker Connector

12 3

9 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Installation

Transmitter

Mounting

If the transmitter will not be installed in an AV rack, then leave the rubber feet in place. If the

transmitter will be installed in an av rack, then remove the four rubber feet from the base.

Step 1

Use the supplied M3 screws to install the rack ears onto the chassis.

Step 2

Mount the Transmitter into the rack.

Power Connections

Step 1

Connect the provided 120/240 VAC power adapter to the rear power supply input, and plug into a

suitable wall outlet.

Antenna And Cable Connections

Step 1 (If Not in a Rack)

If the transmitter is not installed in a rack, the antenna may be installed directly onto the TX module.

The antenna connector is reverse (left) thread. Screw the antenna onto the TX module by turning

the outer nut left. Hand-Tighten only.

Step 2 (If in a Rack)

• If the transmitter is installed in a rack, the Remote Antenna Cable should be used and the

antenna should be placed outside of any and all steel if possible.

• Connect the female threaded end of the cable onto the TX module. The connector is reverse

(left) thread. Screw the cable onto the TX module by turning the outer nut left. Hand-Tighten

only.

• Route the coax cable accordingly. Decide the mounting location of the antenna. The supplied

Remote Mount Bracket can be used by simply drilling the appropriate holes (antenna

connector and mounting screws or zip ties).

• Drill a ¼” (6.35mm) diameter hole into the supplied Mount Bracket (or other surface) for the

bulkhead connector to go through. The surface thickness maximum is 0.10” (2.54mm) to allow

antenna to tighten onto connector.

• Insert the bulkhead ﬁtting through the bracket or surface and install the washer and nut snug.

• Secure the Mount Bracket to the mounting surface using screws, zip ties, etc.

• Screw the antenna onto the bulkhead connector. The antenna connector is reverse (left)

thread. Screw the antenna onto the TX module by turning the outer nut left. Hand-Tighten

only.

10 of 16 ISSUED: 08-30-13 SHEET #: 180-9051-1

Note: For best transmission the antenna should be positioned straight or at a 90° angle once screwed

onto the bulkhead connector. Not turned 180° facing the cable.

TX Module Connections

Step 1

Insert the ADS100-TX14 module into the rear connector labeled “Transmit 1-4”. Be sure alignment

pin goes into matching hole.

Step 2

Secure the TX module by inserting the supplied M3 screw in the locking hole. The button and light

operations are covered in the Operations sections.

Input Signal Connection - Speaker Level Option

Step 1

Connect the speaker outputs of the audio device to the speaker level input plug on the ADS100-T8.

(Note what speaker output is feeding into which input.) Be sure to follow the positive (left) and

negative (right) nomenclature.

Note: If utilizing a channel to feed a remotely located subwoofer, the subwoofer (passive or powered)

will need to accept speaker level inputs as there is no line level output on the Audio Ampliﬁer.

Note: Maximum input power is 150 watts per input/channel.

Input Signal Connection - Line Level Option

Step 1

Plug the desired device line level outputs directly into the line level RCA inputs of the ADS100-T8

Transmitter.

Example: iPod connection through line level will only allow volume control through the iPod.

Note: Connecting a source device, which does not have direct level control, will result in the volume

level set to max with no way to control it.

Note: Each input is independent, which allows the user to use both line level and speaker level inputs

across the 8 inputs as needed.

The Transmitter comes with a 4-channel transmitter ADS100-TX14 module. The second bank of four

channels requires an additional accessory, (ADS100-TX58) and is available separately.

Inhaltsverzeichnis

Andere peerless-AV Stereoanlage Handbücher

peerless-AV

peerless-AV peerSound Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken

LG CM3330B Bedienungsanleitung

Sony

Sony SS-CEP50 Bedienungsanleitung

Cetacea Sound

Cetacea Sound CVS-II Bedienungsanleitung

Denon

Denon UCD-250 Bedienungsanleitung

Sanyo

Sanyo DC-MX41i Bedienungsanleitung

Sharp

Sharp CD-ES600V Bedienungsanleitung

Exibel

Exibel BDX600-UK Bedienungsanleitung

Sanyo

Sanyo DC-F320 Bedienungsanleitung

Philips

Philips FWM583X Bedienungsanleitung

Sharp

Sharp CD-C462 Bedienungsanleitung

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Bedienungsanleitung

Aiwa

Aiwa XR-EM70 Bedienungsanleitung

Cyrus

Cyrus Lyric Bedienungsanleitung

Philips

Philips MCM159/98 Bedienungsanleitung

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Bedienungsanleitung

RCA

RCA RS3965SB Bedienungsanleitung

Sharp

Sharp XL-UH240 Bedienungsanleitung

Philips

Philips FW 690 Bedienungsanleitung

peerless-AV PeerSound ADS100-B Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken