peerless-AV LCZ-4F430B Leitfaden
ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Max Load Capacity per display: 19.8 lb (9 kg)
Installation and Assembly:
Widescreen Quad Monitor Table Stand for 20" - 30" Displays
Models: LCZ-4F430B
2 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation of Base.................................................................................................................................................................4
Attaching Mounting Plates to Display.....................................................................................................................................6
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• Be sure to use designated fasteners and tools to assemble product. If correct fasteners and tools are not used,
product may fail.
3 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
Description Qt
y
Abase 1
Bmounting bracket 4
Cpole 1
Dlock collar 2
Ecrossbar 2
FM4 x 12mm screw 16
GM4 x 30mm screw 16
Hspacer 16
Iknob 4
Jcable clip 2
K3mm allen wrench 1
L4mm allen wrench 1
Parts List
A
B
CDFG
H
E
K
L
J
I
4 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
Remove base cover from base (A) as shown in figure 1.1.
Hand tighten pole (C) onto base (A) as shown in figure 1.2. Tigthen set screw to secure pole using 3mm allen
wrench (K) as shown in rear view.
Feed cables through base cover. Insert base cover
onto pole (C). Insert lock collar (D) onto pole (C).
Adjust to desired height and tighten by hand.
BASE COVER
BASE COVER
1
2 3
Installation of Base
A
C
C
C
D
REAR VIEW
fig 1.1 fig 1.2
SET SCREW
5 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
Insert crossbar (E) onto pole (C) and let it rest on lock collar (D) as shown in figure 4.1.
Adjust rotation of crossbar and hand tighten knob as shown in figure 4.2.
Repeat steps 3 and 4 for second lock collar (D) and crossbar (E).
4
D
C
E
fig 4.1
fig 4.2
KNOB
CROSSBAR COVERS
CABLES
Cables may be routed through crossbar by removing crossbar covers.
5
6 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
Attaching Mounting Plates to Display
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. If display has knobs on the back, remove them to allow the mounting plates to be attached.
Place mounting plates (B) on back of display.
Choose hole pattern as shown in detail 1.
FOR DISPLAYS WITH FLAT BACKS: Attach mounting plates (B) to display using four 12mm screws (F) as shown
in figure 6.1.
FOR DISPLAYS WITH RECESSED BACKS: Attach mounting plates (B) to display using four 30mm screws (G)
and four spacers (H) as shown in figure 6.2.
• Tighten screws so mounting plates are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
VESA 100mm
VESA 75mm
VESA 75mm VESA 100mm
DETAIL 1
fig 6.1
fig 6.2
6
B
B
G
H
F
7 of 23 ISSUED: 04-05-11 SHEET #: 090-9200-3 05-29-12
Hook mounting brackets (B) onto crossbar (E).
Adjust position of displays horizontally to desired location and install knobs (I) into rear of mounting brackets.
Knobs (I) may be tightened using 3mm allen wrench (K).
7
B
E
Cables may be routed using cable clip (J).
8
I
I
J
CABLES
PUBLICADO: 04-05-11 HOJA #: 090-9200-3 05-29-12
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Instalación y ensamblaje:
Estante de mesa para cuatro monitores de pantalla ancha
de 20" a 30"
Modelo: LCZ-4F430B
Capacidad máxima de soportar carga
por pantalla:19.8 lb (9kg)
Español
9 de 23 PUBLICADO: 04-05-11 HOJA #: 090-9200-3 05-29-12
Tabla de contenido
Lista de piezas..................................................................................................................................................................... 10
Instalación de la base...........................................................................................................................................................11
Fijación de las placas de montaje en la pantalla................................................................................................................. 13
Nota: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las ad-
vertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente
internacional, por favor, comuníquese con su distribuidor local.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga experi-
encia en construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los
fijadores y componentes.
• Nunca sobrepase la capacidad máxima de soportar carga aceptada. Vea la página 8.
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
con más seguridad.
• Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede dis-
minuir significativamente su fuerza de fijación.
• Asegúrese de utilizar los sujetadores y las herramientas indicados para armar el producto. Si no utiliza los sujeta-
dores y las herramientas indicados, el producto podría fallar.
ADVERTENCIA
Español
10 de 23 PUBLICADO: 04-05-11 HOJA #: 090-9200-3 05-29-12
A
B
Las piezas pueden verse un poco distintas a la ilustración.
Antes de comenzar, asegúrese de que su producto contiene todas las piezas que se muestran.
Descripción Cant.
Abase 1
Bsoporte de montaje 4
Cposte 1
Dcollar de fijación 2
Ebarra transversal 2
Ftornillos de M4 x 12mm 16
Gtornillos de M4 x 30mm 16
Hespaciadores 16
Iperillas 4
Jclip para cables 2
Kllave allen de 3mm 1
Lllave allen de 4mm 1
Lista de piezas
CDFG
H
E
K
L
J
I
Inhaltsverzeichnis
Sprachen:
Andere peerless-AV TV-Halterung Handbücher
peerless-AV
peerless-AV PLA60 Leitfaden
peerless-AV
peerless-AV DS509 Leitfaden
peerless-AV
peerless-AV ACC-SB Leitfaden
peerless-AV
peerless-AV PT640 Bedienungsanleitung
peerless-AV
peerless-AV ACC953 Leitfaden
peerless-AV
peerless-AV ACC450 Leitfaden
peerless-AV
peerless-AV PFLP650 Bedienungsanleitung
peerless-AV
peerless-AV DS-LEDP Series Bedienungsanleitung
peerless-AV
peerless-AV ECMU-01-I-S Leitfaden
peerless-AV
peerless-AV SR555M Bedienungsanleitung
peerless-AV
peerless-AV SS560DPB Leitfaden
peerless-AV
peerless-AV DS-S560-1X3 Bedienungsanleitung
peerless-AV
peerless-AV SS560F Leitfaden
peerless-AV
peerless-AV SC560DPB Leitfaden
peerless-AV
peerless-AV 8PEDSVW765LAND Bedienungsanleitung
peerless-AV
peerless-AV HLG440-PH Leitfaden
peerless-AV
peerless-AV PFT640 Bedienungsanleitung
peerless-AV
peerless-AV LCT620AD-G Bedienungsanleitung
peerless-AV
peerless-AV SUF660P Bedienungsanleitung
peerless-AV
peerless-AV DS-S560-1X3 Bedienungsanleitung
