Peerless-AV PLAV70-UNL-S Leitfaden

Models: PLAV70-UNL,

PLAV70-UNL-S, PLAV70-UNLP,

PLAV70-UNLP-S

Installation and Assembly - Universal Articulating

Swivel Double-Arm for 42" - 95" Plasma Screens

ISSUED: 06-05-06 SHEET #: 202-9142-10 (2013-03-17)

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Max UL Load Capacity:

200 lb (91 kg)

2 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• drill

• 7/32" drill bit for wood studs

• 3/8" masonry drill bit for concrete

• 7/16" socket wrench with extension (recommended)

• level

• phillips screwdriver

• 3/4" open-end wrench

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724,

WSP724-S) (Metal Stud not evaluated by UL)

NOTE: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - ACC415;

(not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Some parts may appear slightly different than illustrated.

DEF

NOPT

MR S

Parts List PLAV70-UNL

PLAV70-UNLP

Part #

PLAV70-UNL-S

PLAV70-UNLP-S

Part #

Description Qty

Awall plate 1 201-1040 201-4040

Btilt-roll assembly 1 201-1042 201-4042

Carm assembly 1 201-1044 201-4044

Dwall support arm axle 2 201-1041 201-1041

Evinyl trim 3 600-1012 600-1012

FM10 x 15mm screw bolt 8 520-9262 520-9262

G.505 x .062" nylon washer 1 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315

J1.525 x .062" delrin washer 4 540-1070 540-1070

K#8-32 x .375" socket screw 2 520-1210 520-1210

Lplastic ﬁnishing cap 6 590-1123 590-1123

Mholding pin 2 580-1166 580-1166

Nretainer plug 2 590-1007 590-1007

O5/16 x 3" wood screw 8 520-1243 520-1243

P.250 x .068" washer 8 540-1063 540-1063

Q9/64" allen wrench 1 560-9728 560-9728

Rcable management clips 8 590-1166 590-1166

Scable tie 8 590-1168 590-1168

T36" polyester mesh sleeve 2 600-1015 600-1015

U6mm allen wrench 1 560-9716 560-9716

Vconcrete anchor 6 590-0321 590-0321

4 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

AA BB CC

Phillips Adapter Bracket Fasteners

M5 x 12 mm (4)

(520-1027)

M5 x 25 mm (4)

(520-9543)

M6 x 12 mm (4)

(520-1128)

M6 x 25 mm (4)

(520-1208)

.75" spacer (4)

(540-1059)

Multi-washer (4)

(580-1398)

M8 x 25 mm (4)

(520-1031)

M8 x 12 mm (4)

(520-9571)

M5 x 25mm (4)

(520-1122)

M5 x 12mm (4)

(520-1064) M6 x 12mm (4)

(520-1050)

M6 x 25mm (4)

(520-1211) M8 x 25mm (4)

(520-1101)

M8 x 12mm (4)

(520-1724) .75" spacer (4)

(540-1059)

Multi-washer (4)

(580-1398)

Security Adapter Bracket Fasteners

Parts List PLAV70-UNL

Part # PLAV70-UNL-S

Part # PLAV70-UNLP

Part # PLAV70-UNLP-S

Part #Description Qty

AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110

BB shallow adapter bracket 2 202-1655 202-4655 202-1656 202-4656

CC 4mm allen wrench 1 560-9646 560-9646 560-0072 560-0072

5 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud ﬁnder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .43" below the

desired screen center. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it

using eight 5/16 x 3" wood screws (O) and washers (P).

Skip to step 2 on page 7.

Installation to Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

6 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Use wall plate (A), making sure that it is level, as

a template to mark holes. The top mounting slots

should be located .43" below the desired screen

center. Use the masonry bit to drill 3/8" (10mm)

dia. holes to a minimum depth of 3" (76 mm). Insert

anchors (V) in holes ﬂush with wall as shown (right).

Place wall plate (A) over anchors (V) and secure

with 5/16 x 3" wood screws (O) and washers (P).

Installation to Solid Concrete or Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten wood screws so that wall plate is ﬁrmly at-

tached, but do not overtighten. Overtightening can

damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to con-

crete covered with plaster, drywall, or other ﬁnishing

material. If mounting to concrete surfaces covered

with a ﬁnishing surface is unavoidable (not evaluated

by UL), the ﬁnishing surface must be counterbored

as shown below. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer

(not evaluated by UL).

WARNING

Drill holes and insert anchors (V).

Place plate (A) over anchors (V) and secure with screws (Q).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

7 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

To route cables through cord management

channels: Slide one mesh sleeve (T) over

each cable. Use cable ties (S) to tighten mesh

sleeves to cables.

Pull cords through cord management

channels, leaving enough slack to allow full

range of movement for swing arm assembly

3-1

ﬁg 3.1

To route cables using cable management clips:

Snap eight cable management clips(R) into both

swing arms (C) as shown in ﬁgure 3.2.Cable ties

(S) are used with clips for cord management.

Slide one mesh sleeve (T) over each cable. Use

cable ties (S) to tighten mesh sleeves to cables.

CORD

MANAGEMENT

CHANNEL C

3-1

Note: There are three mounting positions.

The center position is shown right. Arm

assemblies must be mounted with one

mounting hole separating them. Slide washers

(J) over wall support arm axles (D). Next, insert

plastic caps (N) into axles. Then, insert holding

pins (M) into axles. See detail 1.

Note: Fit of axles (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

Insert socket cap screws (K) into hole at bottom

of wall support arm axles (D) as shown in detail 3.

Tighten screw using 9/64" allen wrench (Q).

Place arm assembly (C) with washers (J) into

wall plate (A). Insert axle assemblies shown in

detail 1 through wall plate (A), arm assembly (C),

and washers (J). Lock axles in place by aligning

holding pins (M) with notches shown in detail 2.

2-1

2-2

DETAIL 3

NOTCH

DETAIL 2

DETAIL 1

ﬁg 3.2

• If you are uncertain that product is properly installed, call customer care.

WARNING

8 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B). Attach tilt-roll assembly to adapter bracket

(AA) with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

• Do not overtighten screws! Overtightening may hin-

der roll option.

CAUTION

Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on

arm assembly (C).

Insert one ﬁnishing cap (L) into each unused hole of wall plate (A).

4-1

SWIVEL BOX

9 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.

.25" F

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

SWIVEL BOX

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in ﬁgure 6.1. Install nylon washer (G) and tilt

adjustment knob (H).

Install remaining two M10 screws (F) as shown in

ﬁgure 6.2. HAND TIGHTEN all four M10 screws to

allow for tilt adjustment. Remove tape from carriage

bolt (I). For tilt adjustment, gently push back on the

top of plasma to relieve pressure on knob. Adjust tilt

to desired position and tighten tilt adjustment knob

(H), then securely tighten all four M10 screws (F)

using 6 mm allen wrench (U).

6-1

6-2

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

SWIVEL BOX ﬁg 6.1 ﬁg 6.2

• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.

WARNING

10 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-10 (2014-03-17)

Note: "X" dimensions should be equal.

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

Installing Adapter Brackets

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen. Place

screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs,

base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the

adapter brackets to be attached. Select the small, medium, large or extra large screws from the bafﬂed fastener

pack then attach adapter brackets (BB) to screen following ﬁgure 7.1 or 7.2.

NOTE: Top and bottom mounting holes on screen must be used for attaching brackets. Verify that all holes are

properly aligned, and then tighten screws using a phillips screwdriver.

BB CENTER

BRACKETS

VERTICALLY

ON BACK OF

SCREEN

NOTE: For ﬂat back screens proceed to step 7-1. For bump-out or recessed back screen skip to step 7-2.

MEDIUM HOLE FOR M5 SCREWS

LARGE HOLE FOR M6 SCREWS

Notes:

• The number of fasteners used will vary, depending upon

the type of screen.

• Multi-washers and spacers may not be used, depending

upon the type of screen.

• Use the corresponding hole in the multi-washer that

matches your screw size as shown.

MULTI-WASHER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere peerless-AV TV-Halterung Handbücher

peerless-AV

peerless-AV PTL635 Bedienungsanleitung

peerless-AV

peerless-AV FPZ-655 Leitfaden

peerless-AV

peerless-AV DS-MBY942L-2X1 Bedienungsanleitung

peerless-AV

peerless-AV PFL635 Bedienungsanleitung

peerless-AV

peerless-AV PLP-UNM Leitfaden

peerless-AV

peerless-AV WL-ST660-200 Bedienungsanleitung

peerless-AV

peerless-AV Paramount PA746 Bedienungsanleitung

peerless-AV

peerless-AV ESA763PU Leitfaden

peerless-AV

peerless-AV Paramount PT660 Bedienungsanleitung

peerless-AV

peerless-AV SAX762PU Leitfaden

peerless-AV

peerless-AV SS560DPB Leitfaden

peerless-AV

peerless-AV DS-VW765-POR Bedienungsanleitung

peerless-AV

peerless-AV Neptune Bedienungsanleitung

peerless-AV

peerless-AV MIS987 Bedienungsanleitung

peerless-AV

peerless-AV PDW T XL Leitfaden

peerless-AV

peerless-AV DS-MBZ942L-3X1 Bedienungsanleitung

peerless-AV

peerless-AV ACC-V1500X Bedienungsanleitung

peerless-AV

peerless-AV LCT620AQ-G Bedienungsanleitung

peerless-AV

peerless-AV Designer SUA771PU Series Bedienungsanleitung

peerless-AV

peerless-AV SUT646P Bedienungsanleitung

peerless-AV

peerless-AV LCZ-3F419B Leitfaden

peerless-AV

peerless-AV ACC-SB Leitfaden

peerless-AV

peerless-AV PF660 Bedienungsanleitung

peerless-AV

peerless-AV SmartMount SP735P-S Leitfaden

Beliebte TV-Halterung Handbücher anderer Marken

Ergotron

Ergotron Neo Flex Cantilever UHD Bedienungsanleitung

StarTech.com

StarTech.com FPCEILBTB Bedienungsanleitung

VonHaus

VonHaus 05/038 Bedienungsanleitung

Techlink

Techlink ECHO TV Bedienungsanleitung

Sandstrom

Sandstrom SSTVMC12X Bedienungsanleitung

Sony

Sony SU-WL700 Leitfaden

ICW

ICW SCACC18 Bedienungsanleitung

LG WM-L640V Bedienungsanleitung

Gembird

Gembird WM-65ST-01 Bedienungsanleitung

ERARD

ERARD FiTUP XXL 035320 Bedienungsanleitung

PEERLESS

PEERLESS PLCK-1 Leitfaden

Kanto

Kanto RCF180 Bedienungsanleitung

GEM

GEM GEM GP001 Bedienungsanleitung

Gladiator Joe

Gladiator Joe GJ0A0053 Bedienungsanleitung

Vivotek

Vivotek AM-105 Bedienungsanleitung

Vivo

Vivo VESA STAND-VAD1B Bedienungsanleitung

AmazonBasics

AmazonBasics B07QG3LMG4 Bedienungsanleitung

Secura

Secura QLF210 Bedienungsanleitung

peerless-AV PLAV70-UNL-S Leitfaden

Beliebte TV-Halterung Handbücher anderer Marken