peerless-AV SUA765PU Leitfaden
Installation and Assembly:
Peerless Ultra-Thin Articulating Mount for 50" to 75"*
Flat Panel Displays
Models: SUA765PU
*Display Compatibility Requirements
• Depth of display must be less than 2"
• The depth of this mount (1.24") may not provide
sufficient space for proper ventilation on some displays.
Please refer to the manufacturer's requirements for
mounting your display before installation.
• The display must have a flat mounting surface, or the
mounting holes need to be on the furthest back surface
of the display.
• Input/Output connection must be properly oriented to
accommodate mounting 1.24" from the wall.
ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
Max Load Capacity: 100 lb (45.4 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
2 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
NOTE: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This mount is designed to attach the display 1.24" from the wall. Please refer to manufacturer's installation guide
recommendations for required distance from wall to avoid risk of injury or property damage.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
• Wood Beam Included
• Solid Concrete Included
• Cinder Block Included
WARNING
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" (8mm) bit for concrete and cinder block wall
• 5/32" (4mm) bit for wood stud wall
• level
Table of Contents
Parts List.................................................................................................................................................................................3
Wall installation...................................................................................................................................................................4, 5
Installing Adapter Brackets to Display ....................................................................................................................................6
Mounting Flat Panel Display...................................................................................................................................................8
3 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
G
Parts may appear slightly different than illustrated.
A
B
Before you begin, make sure all parts shown are included with your product.
CDEFH
Adapter Bracket Fasteners
I
J
Parts List Part #Description Qty
Awall arm 1 046-P1323
Badapter bracket 2 046-P1225
Cwood screw 4 500-1090
Dconcrete anchor 4 590-0320
EM4 x 6mm 2 520-1006
Fallen bit 1 560-1133
G4mm allen wrench 1 560-9646
Hscrew cap 8 046-0096
Icable clip 1 046-P1137
Jcable tie 2 046-0136
M8 x 25mm (4)
(560-1737)
M8 x 16mm (4)
(560-1264)
M6 x 12mm (4)
(560-1734)
.75" spacer (8)
(600-1215)
.04" washer (4)
(540-9478)
M6 x 25mm (4)
(560-1735)
M8 x 12mm (4)
(560-1736)
4 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
Installation to Wood Stud Wall
Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down each stud’s center. Center of display mounting plate will be 9.26"
offset from center of outer mounting slot as shown in figure 1.1 or will be 6.94" offset from center of inner mounting
slot as shown in figure 1.2. Place wall arm (A) on wall as template, level, and mark the center of four mounting
holes. Top mounting slot will be 6.60" (168mm) above display mounting plate as shown in figure 1.1.
Drill four 5/32" dia. holes to a minimum depth of 2.5". Secure wall arm (A) to wall with four wood screws (C) as
shown in figure 1.2. NOTE: Be sure arrow is pointing up when mounting wall arm (A) to wall as shown in figure 1.1.
Level, then tighten all fasteners.
Insert eight fastener caps (H) into wall plate mounting holes.
A
C
H
fig. 1.1
fig. 1.2
1
6.60"
(168mm)
9.26"
(235mm)
6.94"
(176mm)
= CENTER OF DISPLAY
DISPLAY
MOUNTING PLATE
• When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that the
wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
WARNING
5 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
Installation to Solid Concrete or Cinder Block
NOTE: Wall arm assembly (A) must be mounted to
wall using inner mounting holes.
Make sure that wall arm assembly is level and use
wall plate as a template to mark four mounting
holes. The top mounting slots should be located
6.60" (168mm) above the desired display center as
shown in figure 1.1 on page 4. Drill four 5/16" (8mm)
dia. holes to a minimum depth of 2.5" (64mm).
Insert anchors (D) in holes flush with wall as
shown. Place wall arm assembly over anchors and
secure with wood screws (C). Level, then tighten
all fasteners. Insert eight fastener caps (H) into
mounting holes. NOTE: Be sure arrow is pointing
up when mounting wall arm assembly (A) to wall as
shown in figure 1.1.
C
H
A
D
SOLID CONCRETE CINDER BLOCK
1
F
1
3
D
Drill holes and insert anchors (D).
Place plate (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
2
D
A
C
concrete
surface
• When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi.
• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90 specifications
and have a minimum nominal width of 8".
• Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the
side of the block. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Never attach concrete expansion anchors to concrete or cinder block covered with plaster, drywall or other finishing
material.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
WARNING
6 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
• Tighten screws so display brackets are firmly attached to display. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing
screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
Installing Adapter Brackets to Display
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. If display has obstructions on the back, remove them to allow the adapter brackets to be
attached. Place adapter brackets (B) on back of display, align to holes, and center vertically on back of display as
shown below. Attach the adapter brackets to the back of the display using the appropriate combination of screws,
washers, and spacers as shown in steps 2-1 or 2-2.
NOTE: Top and bottom holes must always be used.
Verify that all holes are properly aligned, and then tighten screws using allen wrench (G).
2
X
X
CENTER
BRACKETS
VERTICALLY
ON BACK OF
DISPLAY
NOTE: "X" dimensions should be equal.
B
NOTE: For flat back displays proceed to step 2-1. For bump-out or recessed back display skip to step 2-2.
NOTE: LATCH
INDICATES
BOTTOM OF
BRACKETS (B)
WARNING
7 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
For Flat Back Display
For Bump-out or Recessed Back Display
2-2
Begin with the shortest length screw, hand thread through washer, tilt bracket and spacer (where required for
ventilation) into display as shown below. If screw cannot make three full turns into the display and fit snug into
place, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level
brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
NOTE: If display manufacturer's requirements state that more than 1.2" of ventilation is required, spacers may be
used to add an additional 0.75" of space between the wall and the display as shown below.
Begin with the shortest length screw, hand thread through washer, tilt bracket and spacer in that order into display
as shown below. If screw cannot make three full turns into the display and fit snug into place, select a longer
length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten
screws.
WASHER
ADAPTER BRACKET (B)
DISPLAY
SCREW
DISPLAY
SCREW
ADAPTER BRACKET (B)
SPACER
WASHER
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
DISPLAY
SCREW
ADAPTER BRACKET (B)
SPACER
WASHER
2-1
8 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
Wall arm assembly (A) must be in closed position to
hang display.
Rotate safety latch with flathead screwdriver into
unlocked position as shown in detail 1.
Hook adapter brackets (B) onto the center of wall arm
assembly (A) adapter plate as shown in figure 3.1.
Mounting and Removing Flat Panel Display
• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel displays.
• Be careful not to pinch fingers when opening and closing mount from the wall.
• DO NOT operate or tilt arm assembly when safety latches are in unlocked position. Product may fail and may cause
injury or damage to display.
• Do not tighten safety/security screw (E) with excessive force. Overtightening can cause screw head to become
damaged making it difficult to remove. Tighten screws to 15 in•lb (1.7 N.M.) maximum torque.
WARNING
3
SAFETY LATCH
DETAIL 1
A
B
fig. 3.1
SAFETY
LATCH
DETAIL 2
DETAIL 3
A
B
E
Rotate safety latch with flathead screwdriver. Install
safety/security screw (E) through safety latch into
adapter bracket with phillips screwdriver to lock
down as shown in detail 2 and 3.
9 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14
Cable Management
Cables may be routed using cable clip (I).
Slip cable clip (I) onto bottom of center joint as shown in figure 5.1 and secure cables to cable clip using cable tie
(J) as shown in figure 5.2.
Secure cables to bottom of wall plate using cable tie (J) as shown below.
5
fig. 5.1 fig. 5.2
I
CENTER
JOINT J
CABLES
J
CABLES
WALL PLATE
SLOTS
© 2014, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerless-av.com
Instalación y ensamblaje:
Soporte Articulador Peerless Ultra-Delgado Para Pantallas
Planas de 50" a 75"*
Modelos: SUA765PU
Máxima capacidad de carga para: 100 lb (45.4 kg)
PUBLICADO: 05-01-11 HOJA #: 095-9358-6 06-04-14
* Requisitos para la compatibilidad de las pantallas
• La profundidad de la pantalla tiene que ser menos de 2".
• Es posible que la profundidad del soporte (1.24") no
proporcione suficiente espacio para la ventilación
adecuada de algunas pantallas. Por favor, repase los
requisitos del fabricante en relación con la instalación de
la pantalla antes de proceder.
• La pantalla tiene que tener una superficie plana para la
instalación o tiene que tener los agujeros de montaje en
la superficie trasera más alejada de la pantalla.
• La conexión de entrada / salida tiene que tener la
orientación adecuada para acomodar una instalación a
1.24" de la pared.
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Inhaltsverzeichnis
Sprachen:
Andere peerless-AV TV-Halterung Handbücher
peerless-AV
peerless-AV HDS-ASR1 Bedienungsanleitung
peerless-AV
peerless-AV LCT620AQ-G Bedienungsanleitung
peerless-AV
peerless-AV LCT620AD-G Bedienungsanleitung
peerless-AV
peerless-AV ECMU-01-I-S Leitfaden
peerless-AV
peerless-AV HLG440-PH Leitfaden
peerless-AV
peerless-AV SFL624 Bedienungsanleitung
peerless-AV
peerless-AV YBTLU Bedienungsanleitung
peerless-AV
peerless-AV SA771P Leitfaden
peerless-AV
peerless-AV DS-MBY942L-2X1 Bedienungsanleitung
peerless-AV
peerless-AV CM850 Leitfaden
peerless-AV
peerless-AV ACC-DSV503 Leitfaden
peerless-AV
peerless-AV PLA60-UNL Leitfaden
peerless-AV
peerless-AV DS-S560-1X3 Bedienungsanleitung
peerless-AV
peerless-AV DS-LEDP Series Bedienungsanleitung
peerless-AV
peerless-AV tru-vue TRWS350/BK Bedienungsanleitung
peerless-AV
peerless-AV MIS987 Bedienungsanleitung
peerless-AV
peerless-AV SmartMount SA746PU Bedienungsanleitung
peerless-AV
peerless-AV DS-S555-3X2 Bedienungsanleitung
peerless-AV
peerless-AV PF660 Bedienungsanleitung
peerless-AV
peerless-AV DS-VW765-POR Bedienungsanleitung
