PEERLESS IB40 Leitfaden
1 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Installation and Assembly:
In-wall Mount for up to 40" Flat Panel Screens
Models: IB40, IB40-S, IB40-W
IN-WALL MOUNT USED WITH ARTICULATING ARM MOUNTS:
PA730, PA740, PP730 and PP740 (NOT INCLUDED)
2 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installing Articulating Arm to In-wall Box.................................................................................................................................5
Attaching Screen ....................................................................................................................................................................5
Cable Management ................................................................................................................................................................6
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill
•5/32" and 1/8" bit for wood stud wall
•level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
• Never exceed the Maximum Load Capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
the hardware included in this product as specified in the installation sheet. To mount this product to an alternative
supporting surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
Wood Beam Contact Customer Service
Solid Concrete Contact Customer Service
Cinder Block Contact Customer Service
Metal Stud Contact Customer Service
Brick Contact Customer Service
Other or unsure? Contact Customer Service
WARNING
3 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
C
F
E
A
G
D
B
H
IB40 IB40-S IB40-W
Description Qty. Part # Part # Part #
Ain-wall box 1 095-P1536 095-C4536 095-2536
B#10 x 1.5" wood screw 2 500-2002 500-2002 500-2002
Cmounting cover plate 2 095-P1533 095-C4533 095-2533
Dribbed rivet 4 590-1296 590-1296 590-1296
Ecable bushing 2 590-1295 590-1295 590-1295
Fcable management clips 4 590-1166 590-1166 590-1166
Gplastic finishing cap 2 590-1123 590-1123 590-1123
Hcable tie 4 590-1168 590-1168 590-1168
Parts List
4 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Installation to Wood Stud Wall
1
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
LEFT
ORIENTATION
RIGHT
ORIENTATION
fig. 1.1
fig. 1.2 fig. 1.3
C
A
fig. 1.4
D
B
A
A
FLANGE
FLANGE
TABS
12-1/4"
(311mm)
14.5"
(368mm)
STUD
6-1/8"
(150mm)
CUT
OUTLINE
CENTER OF
IN-WALL BOX
In-wall box (A) must be installed between two studs 16" on
center. Use an edge-to-edge stud finder to locate the edges
of the stud. Based on its edges, draw two vertical lines down
the inside edges of stud’s. Mark desired center of in-wall box.
Draw a horizontal line 6-1/8" (150 mm) above center of in-wall
box (A). Draw a second horizontal line 12-1/4" (311 mm) below
this line to outline wall opening between inside edges of studs.
Remove drywall inside cut outline.
NOTE: In-wall box (A) can be installed for left or right side
mount orientation as shown in figure 1.2.
Insert in-wall box (A) into cut-out until flange is flush with
drywall.
Level in-wall box (A), and mark the position of two mounting
holes using holes on mounting tabs. Remove in-wall box (A)
and drill 1/8" (3 mm) dia. holes 1-1/2" (38 mm) deep using
the locations previously marked. Reinstall and level in-wall
box (A). Secure using two #10 X 1-1/2" wood screws (B) as
shown in figure 1.3.
Attach two mounting cover plates (C) to in-wall box (A) using
four ribbed rivets (D) as shown in figure 1.4.
5 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Installing Articulating Arm to In-wall Box
Choose hole pattern on interior mounting plate of in-wall box (A) which align with hole pattern on the wall plate of
articulating arm. Mounting hole alignments may be selected for different height installations.
Note: Consider position of screen center or routing of cables before securing arm to in-wall box.
Drill two 5/32" (4 mm) holes 2.5" (65 mm) deep using interior mounting plate holes of in-wall box (A) as a guide.
Attach arm to in-wall box using two #14 x 2-1/2" wood screws (included with articulating arm).
2
Installing Screen to Arm
Refer to instruction included with articulating arm (sold separately) for installation of screen.
3
WALL PLATE OF
ARTICULATING ARM INTERIOR
MOUNTING PLATE
OF IN-WALL BOX (A)
#14 X 2-1/2" WOOD
SCREWS (INCLUDED WITH
ARTICULATING ARM)
MODEL PA740 ARTICULATING ARM SHOWN
(NOT INCLUDED)
• Do not exceed the Maximum Load Capacity indi-
cated on articulating arm instruction.
CAUTION
6 of 6 ISSUED: 12-04-07 SHEET #: 095-9281-4 10-06-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
For optional installation of electrical gang box, access plates located on the bottom or top of in-wall box can be
temporarily removed to install electrical gang box as shown in figure 4.1.
Insert up to four cable management clips (F) into the desired positions in the in-wall box as shown in figure 4.2
for routing cables. Refer to instruction included with articulating arm for cable management with arm.
Insert cable bushing (E) into top or bottom hole of in-wall box for routing cables through in-wall box. Plastic
finishing caps (G) can be used in holes where cables are not being routed.
NOTE: Make sure cables have enough slack to allow full movement of the arm.
Use cable ties (H) to secure cables to cable management clips as shown in figure 4.3.
Cable Management
4
fig. 4.1
ACCESS
PLATE
4-1
SCREEN NOT SHOWN
FOR CLARITY
© 2007, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
MODEL PA740 ARTICULATING ARM SHOWN
(NOT INCLUDED)
F
E or G H
CABLES
fig. 4.2 fig. 4.3
SCREEN NOT SHOWN FOR CLARITY
MODEL PA740 ARTICULATING ARM SHOWN
(NOT INCLUDED)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
