PEGAS CRAFTAP SMART Bedienungsanleitung

Electronic device for fast and

foam-free dispense of beverages

in glass and metal growlers.

Press one button to dispense

Revolution

in beer industry

Designed

for minibreweries,

bars, pubs,

and beer restaurants

beerinnovations.com

Short manual of work

with the menu

CRAFTAP SMART

Working with the device on standby

(«0» is displayed)

One short button press:

"+/-" — setting up a random volume to dispense;

"1","2" or "3" — start dispense of a pre-set volume.

"Menu" — enter user menu/ navigation among the sections

of user and service menues/ exit without saving;

"Set" — adjust a menu section/ save a parameter.

One long button press:

"2" and "3" ("PURGE") simultaneously — purge of the beverage supply hoses (when changing beer sorts);

"1","2" or "3" — display the volumes pre-set for every button.

"Menu" — enter service menu;

"Set" — start a menu function (purge, cleansing, or calibration).

PURGE

Purge

User menu features

Cleansing

Backlights settings

Sound settings

Manual videos can be found on http://beerinnovations.com

Purge time settings

Service menu features

Calibration

Measurement units selection

Password change

Adjustment of the volume

for buttons "1","2","3"

Error codes

No power supply

Pressure is lower than 0,8 atm

Pressure is higher than 3 atm

The beverage is over

The bottle is not ﬁxed or is absent

Hardware error

Make sure that the device is plugged in. Change the keg.

Increase the pressure using

the regulator on the gas bottle. Make sure that the bottle is ﬁxed correctly.

Reduce the pressure using the regulator on the gas bottle. Contact the service center.

CRAFTAP SMART | Working with menu

To change beer sorts:

a. close all taps of the switch;

b. insert the bottle

(ref. to manual of Dispensing, section 1);

c. open the gas supply;

d. purge, then close the gas supply;

e. open the tap with the desired beer sort

Device is ready to dispense.

Purging

Purging of beer chanel with carbon dioxide is done

before a beer sort change when there is a CraftPad

Light ﬂow control switch for CrafTap Smart.

Cleansing

More detailed instructions on cleansing are listed in Service Manual

х 2

х 3

х 4

Stop with

any button

"1","2","3"

Long

pressing

Time passed

since cleaning

started (min. sec)

х 1

Long

pressing

Exit without

saving

Save

Sound settings

Backlights settings

0 — turned off; 1 — always turned on; 2 — turned on while dispensing/ cleaning/ calibrating/ purging and turns off in 20 sec after ﬁnishing

*Default password is "2123"

0 — turned off, 1 — always turned on.

Exit without

saving

Save

Front

illumination

Logo

backlight

System

sounds

Button

sounds

Service menu access

User menu

Enter your

password*

The device

is unlocked

Long

pressing

Manual videos can be found on http://beerinnovations.com

If you do not work in service menu

for 20 sec., it locks up. Enter your

password to unlock.

х 2

х 1

CRAFTAP SMART | Service menu

Set up

required

volume

1 - _ (enter the ﬁrst digit)

2 - _ (enter the second digit)

3 - _ (enter the third digit)

4 - _ (enter the fourth digit)

Service menu sections

(available after accessing menu)

Setting the Volume needed

Using the volume setting function you can pre-set required

volume for each button "1","2" and "3" by yourself.

Select the

button

for which

the volume

is being set

Setting of measurement units

Setting the time of bottle purging. Purging with carbon dioxide is performed to force air out of the bottle

before dispensing.

Calibration is needed if the displayed volume does not correspond with the actual volume dispensed.

To calibrate, use a bottle of the volume more than 1 liter which can withstand the pressure of not lower

than 5 bar. Use a Low-foaming beverage.

Password change

After the calibration, make test dispensing to check the settings accuracy. Repeate the procedure if needed.

Example: If the actual volume ﬁlled is 1018 ml — press "+" and set the difference to "18"; If the actual volume ﬁlled is 985 ml — press "-" and enter the difference of "-15"

Long

pressing

х 4

х 3

Exit without

saving

Save

Exit without

saving

Save

Exit without

saving

Save

Exit without

saving

Save

Time

in seconds Exit without

saving

Save

Liter

Current

measurement unit

American

ounce

British

pint

Manual videos can be found on http://beerinnovations.com

Wait unitl 1 liter is dispensed,

then check the actual

volume ﬁlled

Enter the difference

between the volume ﬁlled

and 1 liter (in milliliters)

beerinnovations.com

3Manual videos can be found on http://beerinnovations.com

Cleansing: daily*

Desinfection: twice a week

Treatment stage Treatment ﬂuid Temperature Time

Time

Cleansing Water 60 °С (140 °F) 15 min

Washing up Water Cold 15 min

Treatment stage Fluid Temperature

Cleansing Water 60 °С (140 °F) 15 min

Desinfection Liquor based on cleansing

detergents "Neomoscan Sepa",

"Termit galo" or similar detergent for

cleansing and desinfection of inner

surfaces of production equipment

in beer and soft drinks industry.

According

to detergent's

manual

15 min

Washing up Water 60 °С (140 °F) Until the cleansing

detergent is

completely absent

in wash water**

Washing up Water Cold

For trouble-free service and fulﬁlment of the warranty obligations declared by the producer

we recommend to service the device regularly. The short service manual provided

can be used as a checklist. We recommend to keep it near the device.

Treatment program

Service Manual

CRAFTAP SMART

*Treatment periodicity — according to regulations in your country.

**Is controlled using absence of residual alkalinity and with the help of universal pH paper.

Preparation step

Disconnect the keg with beverage from

the device and plug the cooler out.

Empty the drainage container.

Using a CraftPad Light ﬂow control switch

for CrafTap Smart:

— close all taps of the switch;

— disconnect the keg with beverage from

the beer tap on the switch, closest to the gas

supply tap.

Open the protective door, place an empty washing

bottle of a small volume on the tray and ﬁx the neck

to the center of the ﬁlling head. Close the door.

For sanitary-hygienic treatment you need:

• gas bottle with carbon dioxide equipped

with a gas pressure regulator;

• keg for cleansing liquid

recommended volume — not less than 20 liters (5 gal);

• cleansing and desinfection detergent;

• neutral detergent;

• intake cap of the keg with beverage;

• cleaning bottle of a small volume;

• drainage container

recommended volume — not less than 20 liters (5 gal);

• cleaning cloth;

• lint-free napkin;

• soft domestic sponge;

• mini-bottle brush with a sponge

or with soft synthetic bristle;

• pliable cleaning hose with outside

diameter of 8 mm (5/16'');

• latex domestic gloves;

• transparent bottle of the maximum

volume possible to be used with the device.

Do not open the protective door

while the pumping of washing

or desinfection liquid through the

device is in progress.

CRAFTAP SMART | Service Manual

4Manual videos can be found on http://beerinnovations.com

To stop the process,

press any button

"1","2" or "3"

Long

pressing

Double

pressing

Time since the cleaning

started (min. sec)

Sequence of steps given in sections 3-9 should be done

for every treatment stage according to the Maintenance program.

Treatment stage

When using CraftPad Light for CrafTap Smart, open the beverage supply tap to which the washing keg

is connected. Then start the cleansing process according to section 6. After the end of the time needed

for a treatment stage, close the beverage supply tap to which the whashing keg is connected.

To reduce consumption of a detergent used at desinfection stage, stop the cleansing process when desinfection liquid starts ﬂowing into

the drainage container. Keep the liquid in the device channels during the time given in Treatment program.

Fill the washing keg with a liquid

of the temperature needed for the treatment

stage being done. (ref. Maintenance program)

Make sure that ﬂask and dispensing unit drainage

hose ends are put into empty drainage container

of the recommended volume.

Make sure, that the gas pressure regulator is set

to 1 bar (15 psi). Connect the intake cap

of the keg with beverage to the washing keg.

Cleansing detergent

CRAFTAP SMART | Service Manual

5Manual videos can be found on http://beerinnovations.com

CRAFTAP SMART | Service Manual

Disconnect the intake cap from the washing

keg without disassembling the gas supply

and the beverage supply hoses.

Empty the drainage container.

Clean the ﬂask drainage channel with a mini-brush,

then wipe the drainage hole with a sponge deeped

into warm water with a neutral detergent.

Wash ﬂask drainage line by pumping washing

liquid appropriate to the a treatment stage

through current it.

At desinfection stage to reduce consumption of a cleansing

detergent, close the drainage hose ending with a plug and keep

the detergent in the line during the exposure time.

Take care of ﬁlling of the drainage container

into which the cleansing liquid ﬂows.

Empty it when ﬁlled.

9Final stage

Washing agent

6Manual videos can be found on http://beerinnovations.com

CRAFTAP SMART | Service Manual

Remove the plate from the drip tray. Twist off the

sleeve of ﬁlling head, disconnect the gasket, remove

the seal out of the groove, and the seal out

of the hole. Wipe disassembled parts with a sponge

deeped into warm water with a neutral detergent.

Wash up all the parts with running water

and wipe them dry with a clean lint-free

cloth. Assemble in backward order.

Wipe the inner surface of the ﬂask with a sponge

deeped warm water with a neutral detergent.

Then wipe inner and outside surfaces with

clean wet cloth. Then wipe the ﬂask dry with

a lint-free cloth.

Before dispensing

Drain water left in the beverage supply line in an empty transparent container of the maximum volume suitable

for the device. Dispense according to instructions in Dispensing manual. Drain the remained liquid until beer

comes into the container.

Then stop dispensing by short pressing

of any button "1","2" or "3".

To keep cleanliness till the next usage of the device

do not pour water used for washing at the ﬁnal

stage out of the beverage supply line. Connect

the intake cap removed from the washing keg

to the beer keg.

Do not forget to close the door

of the device before dispensing.

7Manual videos can be found on http://beerinnovations.com

Installation Manual

CRAFTAP SMART

To install the device quickly, you need:

• 10, 13, 18, 35...70 mm drills;

• ﬂat-head screwdriver;

• 13 mm wrench;

• plastic hoses for beverage and gas supply,

dispensing unit and ﬂask drainage:

hard hoses with outside diameter of 3/8"

or soft hoses with inner diameter of 7 mm;

• hose clips to ﬁx soft hoses on nippels

(if needed).

It is acceptable to use any other appropriate

instrument.

750 mm

400 mm

max 45 mm

Make sure that installation place matches to the

dimensions speciﬁed on the picture and printed

on the stencil. Fasten the stencil and copy the line

pattern on the table top.

Using a drill or electric jigsaw, drill out the holes

in the countertop according to the pattern line.

Using a ﬂat-head screwdriver, twist the pins into

the screw holes at the bottom of the device.

Observe safety rules when

using electrical tools

beerinnovations.com

8Manual videos can be found on http://beerinnovations.com

Inhaltsverzeichnis

Andere PEGAS Küchengerät Handbücher

PEGAS

PEGAS Evolution Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung