Pentair Intellichem 521498 Bedienungsanleitung

INTELLICHEM®CONTROLLER

FIRMWARE UPGRADE KIT

INSTALLATION GUIDE

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IntelliChem Controller Firmware Update Installation Guide

P/N 521499 - Rev C - 10/2019

Kit contents

The following items are included in the Kit P/N 521498

• Programmer IntelliChem®Controller - P/N 521469

• Installation Guide (this manual)

System requirements

• Windows®10, 8 or 7

Technical Support (US)

8 AM to 7.30 PM (US Eastern and Paciﬁc Time)

Phone: (800) 831-7133

Related manuals

IntelliChem Controller Installation and User’s Guide (P/N 521363)

Contents

IntelliChem Controller Firmware Update Instructions............3

Connect the Programmer Cables..........................................3

Installing IntelliChem Controller Firmware Upgrade

Setup Wizard........................................................................4

Programming IntelliChem Controller Firmware.....................4

Troubleshooting ................................................................... 7

IntelliChem Controller Firmware Installation Guide

IntelliChem®Controller Firmware Update Instructions

The IntelliChem Controller ﬁrmware updates are performed using the update

programmer connected to a USB port on a computer running Microsoft®Windows

version 10, 8, or 7.

Connect Programmer Cables

1. Disconnect power to the IntelliChem Controller. Open the front the

cover and disconnect the 18 VAC supply connector J10 on the right

side of the IntelliChem Controller circuit board (as shown below).

2. Note: If there is a mini-circuit board connected to the IntelliChem

Controller circuit board, disconnect the ribbon cable from the

IntelliChem Controller circuit board.

AC Power

Supply

(18VAC)

Connector

(J10)

Disconnect

ribbon cable

(mini-circuit

board)

Mini-circuit board

3. Locate the 6-pin header labeled ISP in the upper-left corner of the

IntelliChem Controller circuit board (as show below).

6-pin header

ISP programming

port

IntelliChem Controller Firmware Update Installation Guide

Connect the

programmer

ribbon cable

with

RED STRIPE

on LEFT SIDE

4. Connect the 6-pin ribbon cable connector to the ISP (on the System

Programming) port with the RED stripe toward the left-side as shown

below.

5. Reconnect the power connector (J10) to the IntelliChem®Controller

circuit board (see page 1).

6. DO NOT connect the micro USB cable to the computer.

Installing IntelliChem Controller Firmware Upgrade SetupWizard

1. Download the Pentair software from:

https://www.pentair.com/en/products/pool-spa-equipment/pool-

automation/intellichem_waterchemistrycontroller.html

2. Navigate to HOMEOWNER AND PRO RESOURCES -> SOFTWARE

3. Download and unzip ﬁle: IntelliChem Firmware Upgrade v1-080.zip

4. If it exists on your computer, Delete directory C:\Pentair\IntelliChem\.

5. From folder ICHEM_1060, Unzip ﬁle: IntelliChem_Firmware_Upgrade_v1-

060.zip

6. Install the ﬁrmware upgrade setup wizard by double-clicking on the ﬁle you just

unzipped IntelliChem_Firmware_Upgrade_v1-060.exe.

Follow screen message to complete the installation.

Note: For Windows 10, the INF conﬁguration ﬁle is not compatible with

this method of installation. Ignore all error messages. Select “OK”

or “CLOSE” to continue and complete the installation.The Avrdude

Programming utility and Pololu driver will be installed.

7. Follow screen message to complete installation.

8. Upon completion of software installation, copy the following two ﬁles to folder

C:\pentair\IntelliChem\ICHEM_Script_1080.bat and ICHEM_v1.080.a90

9. Next, generate a NEW iChem icon pointing to IntelliChem version v1.080.

Right click on ﬁle ICHEM_Script_1080.bat, select Send to, then select

Desktop (create short cut).

Programming IntelliChem Controller Firmware

10. Apply power to the IntelliChem Controller unit and connect the Pololu

ribbon cable to IntelliChem Controller ISP programming port ISP J3.

11. Connect a micro USB cable from the Pololu programmer board to the

computer USB port.

IntelliChem Controller Firmware Installation Guide

12. To verify if the Polulu device driver is installed correctly, Windows

Device Manager should display as shown below.

13. For Windows 7, 8 users: Double-click on the desktop icon “IChem_

Script_1080” to begin programming IntelliChem®Controller ﬁrmware

version 1.080.Wait for programming to complete.

IntelliChem Controller Firmware Update Installation Guide

14. For Windows 10 users:

• Double-click on the desktop icon IChem_Script_1080

• Enter the Pololu USB Programming COM port number ONLY from the

Device Manager (i.e… 3)

IntelliChem Controller Firmware Installation Guide

Troubleshooting

If the programmer exits without showing a progress bar, there was an error in

the setup or installation. Check the following:

a) The programmer is installed correctly

b) IntelliChem®Controller unit is powered on

c) Driver is properly installed

No communication with Pololu Programmer, check USB connection.

No communication with IntelliChem Controller, check connection to ISP

on the IntelliChemController board.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 553-5000

www.pentair.com

All Pentair trademarks and logos are owned by Pentair or by one of its global afﬁliates.

IntelliChem®is a registered trademark of Pentair Water Pool and Spa, Inc. and/or its

afﬁliatedcompaniesin theUnitedStates and/orothercountries.MicrosoftandWindowsis

aregisteredtrademark of MicrosoftCorporation. Because wearecontinuouslyimproving

our products and services, Pentair reserves the right to change speciﬁcations without

prior notice. Pentair is an equal opportunity employer.

to change without notice.

P/N 521499 - Rev C - 10/2019

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pentair Controller Handbücher

Pentair

Pentair 3200NXT Bedienungsanleitung

Pentair

Pentair FLECKXT Bedienungsanleitung

Pentair

Pentair SPEEDEO CONNECT Bedienungsanleitung

Pentair

Pentair FLECK 5800 XTR2 Bedienungsanleitung

Pentair

Pentair AUTOTROL LOGIX 740 Bedienungsanleitung

Pentair

Pentair GOYEN IS Series Bedienungsanleitung

Pentair

Pentair IntelliBrite Bedienungsanleitung

Pentair

Pentair FLECK SXT Bedienungsanleitung

Pentair

Pentair SOLARTOUCH 521592 Bedienungsanleitung

Pentair

Pentair Water Chemistry Controller Smart pH Bedienungsanleitung

Pentair

Pentair intellichem Bedienungsanleitung

Pentair

Pentair HOME SUMP CONTROLLER Montageanleitung

Pentair

Pentair Autotrol 255 Series Bedienungsanleitung

Pentair

Pentair Pentek Solar Drive PSD30 Bedienungsanleitung

Pentair

Pentair Magnum 742-762 Bedienungsanleitung

Pentair

Pentair INTELLIVALVE Bedienungsanleitung

Pentair

Pentair IntelliBrite Bedienungsanleitung

Pentair

Pentair Goyen IS Series Bedienungsanleitung

Pentair

Pentair AUTOTROL 460TC Bedienungsanleitung

Pentair

Pentair AK110 Bedienungsanleitung

Pentair

Pentair AUTOTROL Performa 263 Bedienungsanleitung

Pentair

Pentair AVID XA+ Handbuch

Pentair

Pentair MYERS 19280C Bedienungsanleitung

Pentair

Pentair 962 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung