Pentair ONGA Bedienungsanleitung

Owner’s Manual

Spa Blower

Should the installer or owner be unfamiliar with the correct

installation or operation of this type of equipment you should

contact the distributor/manufacturer for the correct advice before

proceeding with the installation or operation of this product.

Installation & operation

instructions

ONGA

1. Run 50mm PVC pipe line from the spa pool manifold outlet to spa blower position

(maximum operating distance 12 metres), ensuring that the 50mm pipe line has a

minimum fall of 1:10 back to the spa, this will allow the pipe line to have minimum

water lying in the pipe (refer diagram 1).

2. Run your vertical 50mm pvc pipe a minimum of 600mm above

the spa pools maximum water level.

Allow 24 hours for glue vapours to dissipate from the pipe work before

mounting spa blower onto pipe (failure to do so may cause damage to the

spa blower, pipe work and void warranty). Place the blower on the pipe and

tighten the stain-less steel mounting screw located on the check-valve

(refer diagram 1).

DO NOT GLUE THE SPA BLOWER TO THE 50MM PIPE.

SPA BLOWER INSTALLATION AND OPERATION INSTRUCTIONS

3. If the spa blower is to be mounted below water level, extend the

air loop 600mm above the maximum water level and return back to

the spa blower, drill a bleed hole after loop to remove any

condensation (refer diagram 2). DO NOT create a water trap in the

blower supply pipe (refer diagram 3), as the water lying in the pipe

will create additional back pressure on the spa blower. Mount the

spa blower as instructed above (2).

Diagram 1

Diagram 3

Diagram 2

Page 2

These instructions act as a guide only and do not cover every contingency.

People not familiar with pool filtration and pumping equipment should seek

advice from an authorised Onga stockist.

4. If the spa blower is to be used for additional spa jet venturi, connect the

supply line into the air supply line of the spa jet using a tee, then follow the

instructions of 1 & 2 and refer to (diagram 4)

5. Spa blower MUST be mounted in a vertical position only, with the

discharge downwards (refer diagram 1, 2, & 4).

6. If a air switch or three speed option is being fitted a roll of air tube is

supplied, enclose the air line in conduit for mechanical protection, place one

end of the tube onto the nipple of the air button fitted on the spa pool, place

the other end of the air line onto the spa blower, the air nipple is located on

the under side of the spa blower.

7. Place the spa blower 10 amp lead into a 240 volt 50Hz designated power

point.

8. Minimal Air Hole Specifications

36 x 6 mm Diameter Holes

18 x 8 mm Diameter Holes

(refer diagram 5)

IMPORTANT INSTALLER PLEASE NOTE

The diameter and quantity of air holes listed above are based on a spa pool

air manifold maximum water submergence depth of:

(1) 600mm (seat/recliner manifold)

(2) 800mm (footwell manifold)

If the spa depth/manifold dimensions vary from above please contact the

Pentair Water office in your state for advice and verification, failure to

comply may damage the equipment and void the product warranty.

OPERATION OF YOUR SPA BLOWER

1. Switch power on, your spa blower will start.

(a) If your spa blower has been plugged into another controller it may not

start until the air button or some other form of switching has been pressed.

(Check with your installer).

(b) Air Switch Blower Operation

Simply press the air button located on the spa and your spa blower will

start on high speed, press your button again and this will turn the spa

blower off.

WARNING This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure they do not play with the

appliance.

If the supply cord is damaged, the equipment should be discarded or

scrapped.

No part of this appliance is to be located above the spa pool and must be

inaccessible to a person in the spa pool. All parts must be fixed so they cannot

fall into the spa pool.

The appliance should be supplied through a residual current device (RCD) having

a rated current not exceeding 30mA.

Page 3

Spa Blower

Cover 1100508

Motor (1200 Watt) 707431

EMC Filter (units prior to 2016)

707425

Micro Switch N/A

Air Switch Holder N/A

Air Sensor Assembly (Includes Items 4&5) 302470

6 Motor Housing N/A

7 Checkvalve (40mm-50mm) N/A

Motor Housing and Check -Valve Assembly

(Includes Items 6&7)

707435

8 Cowl 707497

TROUBLE SHOOTING GUIDE

SYMPTOM REMEDY

Spa blower will not start. Check power point is switched on and sp a blower is plugged

in. Check Fuses.

Check that air line is connected from the air button to the spa

blower.

Check that the air line is not kinked. If kinks are visible,

remove them otherwise this will stop the pulse of air that

operates the micro switch inside the spa blower.

Check micro switch operation.

Push air button and a faint click should be heard at the spa

blower, if no click is heard check all connections if they are

all OK and spa blower still doesn't start, remove spa blower

and take it to the nearest Pentair Water service agent.

Spa blower is making a grinding noise when operating. Bearings/brushes may need replacing.

Spa blower makes a noise when stopping. This is only the check-valve operating correctly.

Spa blower operates then stops (cutting out on thermal

overload),

Could be caused by blockage or insufficient air holes, check

installation of the spa blower pipe work, ensure that it has

been installed to the specifications, if incorrect call installer.

If all plumbing is correct remove the spa blower and take it to

your nearest Pentair Water service agent.

Page 4

Notes:

Page 5

Notes:

Page 6

Notes:

Page 7

IMPORTANT

Please attach your sales invoice/docket here as proof of purchase should

warranty service be required.

Please do not return Warranty Form to Pentair Australia -

please retain for your records.

Purchased From ...................................................................................................................

Purchase Date..................................... Serial No.............................. Model No........................

display, publication, modif ication or distribution is strictly prohibited without the prior written

permission of Pentair Water Pty Ltd.

Disclaimer: Every endeavour has been made to publish the correct details in this data sheet.

No responsibility will be taken for errors, omissions or changes in product specif ications.

Pentair Water reserves the right to change specif ications

Head Office

Pentair AU/NZ: 1-21 Monash Drive,

Dandenong South, Vic 3175

Australia

National Customer Service: Phone: 1300 137 344

Fax: 1800 006 688

National Dealer Locator: Phone: 1800 664 266

Ema il: au.sales@pentair.com

We b: www.pentair.com.au

International

Phone: +61 3 9709 5800

Fax: +61 3 9709 5888

L300220 B0920

Inhaltsverzeichnis

Andere Pentair Beleuchtungsausrüstung Handbücher

Pentair

Pentair INTELLICHLOR IC60 Bedienungsanleitung

Pentair

Pentair AquaTRAM 360 Bedienungsanleitung

Pentair

Pentair INTELLICHLOR IC15 Bedienungsanleitung

Pentair

Pentair Meteor 20 Bedienungsanleitung

Pentair

Pentair IntelliBrite Bedienungsanleitung

Pentair

Pentair SAND DOLLAR Bedienungsanleitung

Pentair

Pentair MAGICSTREAM LAMINAR Bedienungsanleitung

Pentair

Pentair PG2000 Bedienungsanleitung

Pentair

Pentair IntelliPool Bedienungsanleitung

Pentair

Pentair EasyTouch PNP 5 Bedienungsanleitung

Pentair

Pentair IntelliBrite Bedienungsanleitung

Pentair

Pentair T40-F Bedienungsanleitung

Pentair

Pentair ChemCheck Montage- und Wartungsanleitung

Pentair

Pentair SIATA V132-SFE-EV-VIRIDION Benutzerhandbuch

Pentair

Pentair SOLEO CL Bedienungsanleitung

Pentair

Pentair MAGICSTREAM Deck Jet I Bedienungsanleitung

Pentair

Pentair MagicStream Deck Jet II Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung