Pentair PROWLER 920 Bedienungsanleitung

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PROWLER® 920

ROBOTIC INGROUND POOL CLEANER

INSTALLATION AND

USER’S GUIDE

If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please use

the following contact information:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support

8 A.M. to 5:00 P.M.

Phone: 1300 137 344

Web site

visit www.pentairpool.com.au

to ﬁnd information about Pentair products.

TABLE OF CONTENTS

Maintenance ........................................................

LED Indicator Lights

Removing the Cleaner from the Pool

Cleaning the Filter Basket

Periodic Filter Screen Cleaning

Cleaning the Impeller

Storing the Cleaner

Troubleshooting ..................................................

Replacement Parts ..............................................

Important Warning and Safety Instructions .......

Preperation of the Pool and Cleaner ...................

Overview

Cleaner Components

Cleaner Features

Initial Setup

Operation ...............................................................

Weekly Timer

Setting the Weekly Timer

PROWLER® 920 Robotic Inground Pool Cleaner Installation and User’s Guide

RCD Instructions .............................................. 11

PROWLER® 920 Robotic Inground Pool Cleaner Installation and User’s Guide

INTRODUCTION, SPECIFICATIONS AND WARNINGS

INTRODUCTION

Thank you for purchasing a Pentair Robotic Pool Cleaner.

We are sure that your Pentair Robotic Pool Cleaner will provide you with reliable, convenient

and cost-effective pool cleaning. Its reliable filtration in all pool conditions and active brushing,

enhance pool hygiene.

Robotic Pool Cleaners by Pentair deliver advanced cleaning technologys, long-lasting

performance and easy maintenance. You and your family will be free to enjoy your swim with

full confidence that your pool is completely clean.

SPECIFICATIONS

Motor protection: IP 68

Minimum depth: 0.80m / 2.6ft

Maximum depth: 5m / 16.4ft

WARNINGS AND CAUTIONS

Warnings

• Use the originally supplied power supply only

• Ensure the electrical outlet isprotected by a ground fault interrupter (GFI) or an

earth leakage interrupter (ELI). Or residual current device (RCD) see page 11.

• Keep the power supply out of standing water

• Position the power supply at least 3m/10ft away from the edge of the pool

• Do not enter the pool while the Pool Cleaner is working

• Unplug the power supply before servicing

Cautions

Use the Pool Cleaner in the following water conditions only:

Chlorine Maximum 4 ppm

pH 7.0-7.8

Temperature 6-34°C

NaCl Maximum 5000 ppm

CAUTION

Digital Power supply

Input: 200-230 AC Volts

50-60 Hertz

Output: <30 VDC

IP 54

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Overview

Prowler®920 Robotic Pool Cleaners are designed to scrub, vacuum, and ﬁlter (including the waterline) your inground

pool. Before operating this product, be sure to read and follow all warning and safety instructions on pages ii-iii.

Cleaner Components:

• Cleaner with 60 ft. Floating Cable

• Power Supply

Cleaner Features:

• Weekly Timer

• Wall and Waterline Scrubbing

• Top Loading Basket Filtration

PREPARATION OF THE POOL AND CLEANER

Cleaner with 60 Ft.

Floating Cable Power Supply

STEP 1:

Power Supply and Caddy Placement

Position the power supply at least 10 feet (3 m) from the

edge of the pool. See Figure 1.

STEP 2:

Unroll Floating Cleaner Cable

Unroll the ﬂoating cable and stretch it out completely so

that is has no kinks. See Figure 2.

Initial Setup

Before using the cleaner for the ﬁrst time, perform the following procedures:

Figure 2

Figure 1

STEP 3:

Connect Power Supply to Cleaner

Connect the ﬂoating cleaner cable to the power supply.

Ensure the connector notch is lined up with the

corresponding groove in the socket on the power supply.

Turn the cable connector clockwise to lock the cable into

the power supply connection. See Figure 3.

Figure 3

KREEPY KRAULY® PROWLER® 920 Robotic Inground Pool Cleaner Installation and User’s Guide

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Figure 4

STEP 4:

Connect Power Supply to Power Source

Connect the power supply to the electrical source/outlet.

See Figure 4.

RISK OF ELECTRICAL SHOCK OR

ELECTROCUTION: Connect only to a grounding

type receptacle protected by a ground-fault circuit-interrupter

(GFCI). Contact a qualiﬁed electrician if you cannot verify that the

receptacle is protected by a GFCI.

To reduce the risk of electrical shock, do not use

extension cord to connect unit to electrical supply;

provide a properly located outlet.

Do not switch the pool cleaner to “ON” if it is not

fully immersed in water. Operating the cleaner out

of water will immediately cause severe damage and will result in loss

of warranty. Do not leave the cleaner in the pool all the time. Always

remember to turn the power supply “OFF” and unplug it from the power

outlet before removing the cleaner from the pool.

1. Be sure the power supply is positioned at least 10 feet

(3 m) from the pool.

2. Lower the cleaner into the pool by the handle (see

Figure 5).

Note: Never lower the cleaner into the pool by the

ﬂoating cable. This puts an unnecessary strain on the

cable and could result in damage to the cleaner.

3. Gently tilt the cleaner from side to side or turn upside

down to release trapped air. See Figure 6.

Figure 5 Figure 6

STEP 5:

Placing the Cleaner in the Pool

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

OPERATION

Weekly Timer

The power supply has a timer control that allows you to set an automatic cleaning schedule each week. Be sure the cleaner

is fully immersed in water before turning on the power.

Setting the Weekly Timer

When the power supply is switched on, you may choose a pool cleaning

schedule for the coming week by pressing the Weekly Timer button.

Note: The cleaner will always begin to work upon set-up.

Schedule LEDS:

LED 1 - The cleaner will automatically work every day for a full cycle

= 7 times per week. Press the Weekly Timer button once to

select this interval.

LED 2 - The cleaner will automatically work every other day for a full

cycle = 3 times per week. Press the Weekly Timer button

twice to select this interval.

LED 3 - The cleaner will automatically work every 3 days = 2 times

a week. Press the Weekly Timer button three times to select

this interval.

Pressing the Weekly Timer button four consecutive times will reset the cleaner’s schedule. If you do not press any of the

buttons within the ﬁrst 5 seconds after the power has been switched on, the cleaner will default to running one cycle only.

While the cleaner is working in weekly timer mode, the appropriate Weekly Timer LED will blink constantly between cycles.

At the end of the week the power supply automatically shuts off.

1 2 3

3 Schedule

LEDs

On/Off

Button

Weekly Timer

Button

KREEPY KRAULY® PROWLER® 920 Robotic Inground Pool Cleaner Installation and User’s Guide

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Removing the Cleaner from the Pool

The cleaner will shut off automatically at the end of a cleaning cycle. Follow the steps below

to remove the cleaner from the pool.

1. Disconnect the power supply cable from the electrical outlet and disconnect the

cleaner communication cable from the power supply.

2. Using the ﬂoating cleaner cable, slowly and gently pull the cleaner to the waterline

at the edge of the pool until you can reach the handle. DO NOT lift the cleaner out

of the water by the cable.

3. Using the handle, lift the cleaner out of the pool. See Figure 9.

Note: Never lift the cleaner out of the pool by the ﬂoating cable. This puts an

unnecessary strain on the cable and could result in damage to the cleaner.

4. Place the cleaner on the edge of the pool and allow excess water to drain from the

cleaner body and basket. See Figure 10.

5. Disconnect the ﬂoating cable from the power supply.

6. Store the cleaner in a covered area with the ﬂoating cable coiled.

MAINTENANCE

Ensure the power supply is turned “OFF” and disconnected from the electrical source/outlet

before removing the cleaner from the pool. Operating the cleaner out of water will immediately

cause severe damage and will result in loss of warranty. Do not leave the cleaner in the pool all the time.

Figure 9

Figure 10

LED Indicator Lights

The Prowler®920 Robotic Pool Cleaner includes an LED indicator just

above the scrubber on the front side of the cleaner (see Figure 8). During

normal operation powered by the power supply the LED indicator will

blink blue.

LED

Indicator

Figure 8

Make sure the cleaner’s power supply is turned “OFF” and is disconnected from the electrical source/outlet before servicing

the cleaner. Moving parts may injure hands or ﬁngers if cleaner inadvertently powers on during servicing.

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Cleaning the Filter Basket

Note: It is highly recommended that you clean the ﬁlter basket after each cleaning cycle. Too much debris in the ﬁlter will

restrict the suction power of the Prowler®920 Robotic Pool Cleaner and reduce its effectiveness.

To clean the ﬁlter basket, follow the instructions given below:

Figure 11

STEP 1:

Open the Filter Cover

When the ﬁlter cover is opened the ﬁlter basket handle will

pop up independently. See Figure 12.

Figure 13

STEP 2:

Lift the basket out of the cleaner body.

Figure 12

Figure 14

STEP 3:

Empty the Filter Basket

Open the latch at the bottom of the ﬁlter basket. This will

release the bottom lid of the basket and dump much of the

collected debris. See Figure 14.

Figure 15

STEP 4:

Clean the Filter Basket

Thoroughly clean the ﬁlter basket with a garden hose. See

Figure 15.

KREEPY KRAULY® PROWLER® 920 Robotic Inground Pool Cleaner Installation and User’s Guide

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Periodic Filter Screen Cleaning

Note: It is recommended that you clean the ﬁlter screens at least once a month. Too much debris in the ﬁlter screens will

restrict the suction power of the Prowler®920 Robotic Pool Cleaner and reduce its effectiveness.

To dismantle and clean the four ﬁlter screens, follow the instructions given below.

STEP 1:

Remove the Filter Screens

Using your thumbs, ﬁrmly press inwards on the top of

Panel 1 to remove the ﬁlter screen from its frame (see

Figure 16).

Each ﬁlter screen is stamped with a number (see Figure

17). Remove the ﬁlter screens in numerical order; Screen

1 > 2 > 3 > 4.

Figure 16

Figure 17

STEP 2:

Clean the Filter Screens

Thoroughly clean the ﬁlter screens with a garden hose.

See Figure 18.

Figure 18

STEP 3:

Reassemble the Filter Screens

Replace the ﬁlter screens by seating the bottom of the

screen into its frame, then pushing ﬁrmly outwards on the

top of the screen until a click is heard.

Each ﬁlter screen is stamped with a number (see Figure

19). Replace the ﬁlter screens in numerical order; Screen

4 > 3 > 2 > 1.

Figure 19

PROWLER

920 Robotic Inground Pool Cleaner Installation and User’s Guide

Cleaning the Impeller

Always disconnect power to the cleaner before servicing, disassembly, or reassembly. Failure to do so could result in death or

serious injury to servicemen, pool users or others due to electrical shock. Read all servicing instructions before servicing the cleaner.

Every so often debris may become trapped in the Prowler® 920 Robotic Pool Cleaner’s impeller. To clean out debris

trapped in the impeller opening, follow the instructions below:

STEP 1:

Open the Filter Cover and Remove the Basket

See Figure 20 and Figure 21.

Figure 20

Figure 21

STEP 2:

Unmount and Remove the Intermediate Cover and

Manifold Assembly

1. Using a No. 2 Phillips-head screwdriver, remove the two

screws that hold the intermediate cover and manifold

assembly in place. These screws can be found in the

inside corners of the intermediate cover. See Figure 22.

2. Place the two screws to the side.

3. Gently pull the intermediate cover (Item #2 in Figure 22)

away from the cleaner and place it to the side.

4. Gently pull the manifold assembly (Item #3 in Figure 22)

away from the cleaner and place it to the side.

Figure 22

STEP 3:

Unmount and Remove the Impeller Cover

Press the tabs on both sides of the impeller cover

(Item #1 in Figure 23) to unlock the cover from the

impeller assembly. While pressing both tabs, pull the

cover away from the cleaner.

Place the impeller cover to the side.

Figure 23

Figure 24

STEP 4:

Clean Debris from the Impeller

By hand, remove any debris that has become trapped

around the impeller. See Figure 24.

Andere Handbücher für PROWLER 920

Inhaltsverzeichnis

Andere Pentair Schwimmbadroboter Handbücher

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair Legend LL505G Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY WARRIOR Bedienungsanleitung

Pentair

Pentair LEGEND Bedienungsanleitung

Pentair

Pentair Great White Bedienungsanleitung

Pentair

Pentair GW9500 Bedienungsanleitung

Pentair

Pentair Kreepy Kruiser Bedienungsanleitung

Pentair

Pentair Kreepy Krauly Prowler 930 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

Pentair

Pentair Kreepy Krauly Prowler 930 Bedienungsanleitung

Pentair

Pentair PROWLER P10 Bedienungsanleitung

Pentair

Pentair SandShark Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY PROWLER 920 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair RACER LS Bedienungsanleitung

Pentair

Pentair Prowler 720 Bedienungsanleitung

Pentair

Pentair MiniMax 100 Bedienungsanleitung

Pentair

Pentair Kreepy Krauly Platinum Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY LIL SHARK Bedienungsanleitung

Pentair

Pentair PROWLER 930W Bedienungsanleitung

Pentair

Pentair PROWLER 930W Produkthandbuch

Pentair

Pentair POOLSHARK Bedienungsanleitung

Pentair

Pentair BLUEFURY Bedienungsanleitung

Pentair

Pentair pool cleaner Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung

BWT

BWT BC 30 Bedienungsanleitung

Maytronics

Maytronics Dolphin Triton Ps Bedienungsanleitung