Pentair Side Pool Cleaner Bedienungsanleitung

LEGEND® PLATINUM INSTALLATION MANUAL

LEGEND

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Installation Guide

Pressure Side Pool Cleaner

LEGEND® PLATINUM INSTALLATION MANUAL

This document is subject to change without notice.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Trademarks and Disclaimers. The Pentair Water Pool and Spa logo is a trademark of Pentair Water Pool and Spa, Inc. The Legend Platinum logo

is a registered trademark of Pentair Water Pool and Spa, Inc. Other trademarks and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Pentair Water Pool and Spa, Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Customer Service

If you have questions about ordering Pentair replacement parts, and pool products,

please use the following contact information:

Customer Service (8 A.M. to 5 P.M. — Eastern and Pacific Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Technical Support

Sanford, North Carolina (8 A.M. to 5 P.M. — Eastern Time)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 5 P.M. — Pacific Time)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

Web site

visit www.pentairpool.com and www.staritepool.com to find information about our products

LEGEND® PLATINUM INSTALLATION MANUAL

Important Information:

The Legend®Platinum automatic pool cleaner comes ready to connect into a female threaded 1-1/2"

line, dedicated to our Universal Booster Pump. Also, if you have a chlorinator, solar system or other air

inducing equipment, contact our Technical Support Department at 1-800-831-7133 before you install the

Legend®Platinum. (See diagram on page 2).

The following are important facts to remember before installing and operating the Legend®Platinum.

1. Always disconnect the Legend®Platinum from the pool wall when cleaning or back washing the pool

filter.

2. After cleaning or back washing, let the filtration system run for at least five minutes before reconnecting

the Legend®Platinum.

3. New plumbing lines should be flushed out before installing the Legend®Platinum.

4. The Legend®Platinum should not be used to remove plaster dust in new pools.

5. Always remove the Legend®Platinum before swimmers enter the pool.

6. Always handle the Legend®Platinum with care. Do not let children or pets play with the unit:

it is not a toy.

7. Always pick up the Legend®Platinum by the Vacuum Tube especially when lifting the unit out of the

water.

8. Unless checking the wheel RPM, do not handle the Legend®Platinum while it is operating.

9. Always remove the Legend®Platinum from the pool before chemical shock treatments. As a rule, any

pool water that is unsafe for swimming is unsafe for the Legend®Platinum.

10. Carefully cut the feed hose following the instructions on Page 3.

By following these simple guidelines, you can help protect against injury and prolong the life of

your Legend®Platinum.

Before the Legend®Platinum is installed, please take a moment to record the serial number. This number

is located on your warranty card and on the back of the Legend®Platinum near the rear jets. You will be

asked for this number when you contact our Technical Support Department.

SERIAL #__________________________________

LL105PM / LL105PMG

LL105PMTGG / LL105PMTWW

LL105PMTRW / LL105PMTYW

LEGEND

LEGEND® PLATINUM INSTALLATION MANUAL

TABLE OF CONTENTS

I. Introduction ................................................................................................................................1

A. Thank You for Choosing the Legend®Platinum. ................................................................. 1

B. What to Expect from the Legend®Platinum. ..................................................................... 1

II. Installation Instructions .............................................................................................................. 2

A. Legend®Platinum Components ........................................................................................ 2

B. Pool Connections ............................................................................................................. 2

C. Booster Pump Installation ................................................................................................ 2

D. Installing the Twist Lock Pressure Relief Valve (Wall Fitting) ............................................ 3

E. Cutting the Feed Hose ................................................................................................... 3-6

F. Checking Operation ......................................................................................................... 7

G. Fine Tuning the Legend®Platinum..................................................................................... 7

1. Thrust Jet Adjustment ................................................................................................. 7

2. Sweep Hose Adjustment ............................................................................................. 7

3. Checking Wheel RPM ................................................................................................. 8

III. Operation & Periodic Maintenance ............................................................................................. 9

A. Connecting/Disconnecting the Legend®Platinum ............................................................. 9

B. Turning the Legend®Platinum On/Off ............................................................................... 9

C. Cleaning the Sand & Silt Bag ........................................................................................... 9

D. Periodic Maintenance ....................................................................................................... 9

1. Wall Fitting Screen ...................................................................................................... 9

2. Tires & Bearings ....................................................................................................... 10

3. Roller Rings .............................................................................................................. 10

4. Debris Bags .............................................................................................................. 10

5. Sweep Hose .............................................................................................................. 10

6. Debris Valve .............................................................................................................. 10

E. Back Washing the Pool Filter .......................................................................................... 10

F. Storage and Winterizing ................................................................................................. 10

G. Accessories ...................................................................................................................10

1. Sweep Hose Weight .................................................................................................. 10

2. Leaf Bag ................................................................................................................... 10

IV. Troubleshooting ................................................................................................................... 11-12

Legend®Platinum Parts List ........................................................................................... 13-14

Legend®Platinum Exploded View ........................................................................................ 15

LEGEND® PLATINUM INSTALLATION MANUAL

I. Introduction

A. Thank You for Choosing the

Legend®Platinum Pool Cleaner

Congratulations on the purchase of your new

automatic pool cleaner. The Legend®Platinum is

designed to give you years of dependable and

efficient service. With the Legend®Platinum, you and

your family will spend more time relaxing and

enjoying your pool and less time cleaning it.

The Legend®Platinum has been designed and built

with time proven features and patented innovations

to create an automatic pool cleaner that will give you

years of dependable service. The Legend®Platinum

is built with pride in the U.S.A., by people who care

about the product using state of the art materials and

backed by a limited warranty that protects against

defects in parts and construction.

Like any mechanical device, the Legend®Platinum

requires some preventative maintenance and the

replacement of certain working parts. We

recommend that you have your Legend®Platinum

checked annually. For best results have your

Legend®Platinum installed by a qualified swimming

pool professional.

For pool owners with plumbing and mechanical

experience, installation instructions are included in

this manual.

Please put safety first! Be sure to take your

Legend®Platinum out of your pool and store it

carefully in a shaded area before anyone enters the

pool.

B. What to Expect from the Legend®

Platinum

When operating correctly, the Legend®Platinum will

travel randomly throughout the pool, vacuuming and

sweeping the bottom. The climbing ability of the

Legend®Platinum is dependent on the pool’s shape.

It will climb better in pools without sharp angles or

curves in the transition from the pool floor to the pool

wall.

The Legend®Platinum comes equipped with a

Wall Fitting (Part # EW22-White, Part # LLW22PM-

Gray) that features a Twist Lock Automatic

Pressure Relief Valve. If the Legend®Platinum is

receiving too much water pressure to the unit, the

relief valve will automatically reduce water pressure.

Approximately every three minutes and 30 seconds,

the Legend®Platinum will go into a back up mode.

At this time, the Back Up Valve will pull the Legend®

Platinum away from problem areas.

The Sweep Hose operates in a gentle sweeping

motion to prevent debris from becoming trapped in

hard to reach corners of the pool.

LEGEND® PLATINUM INSTALLATION MANUAL

II. Installation Instructions

A. Legend®Platinum Components

The Legend®Platinum Box Contains:

1. Cleaner Head

2. Sand & Silt Bag

3. Sweep Hose

4. Complete Feed Hose

a. 1 - 8½ in. hose

b. 2 - 10 ft. long hoses

c. 1 - 30 in. soft hose/1 - 7½ ft. soft hose

d. 10 - Floats

e. 3 - Swivels

f. 1- Back-Up Valve

g. 10 - Mender Nuts

h. 1 - Wall Fitting complete

B. Pool Connections

The Legend®Platinum comes equipped to connect

to a female threaded 1-1/2 in. line, dedicated to our

Universal Booster Pump.

Also, if the pool doesn't have a dedicated cleaner

line please contact our Technical Support

Department at 1-800-831-7133.

C. Booster Pump Installation

If you already have a 3/4 horsepower booster pump

installed at your equipment pad and it is operational,

skip this section and proceed to Installing the Twist

Lock Pressure Relief Valve (Wall Fitting).

Detailed booster pump installation instructions are

packaged separately in our booster pump box.

Please follow these instructions carefully.

The booster pump is not self-priming and needs to

be fed with water taken from the pool filter before

any type of in-line chlorinator. See figure below.

LEGEND® PLATINUM INSTALLATION MANUAL

D. Installing the Twist Lock Pressure

Relief Valve (Wall Fitting)

1. Take out any existing pool cleaner and/or wall

fitting.

2. Turn on the filtration pump and booster pump,

flush out the plumbing line.

3. Turn off filter pump and booster pump.

4. Remove the Wall Adapter from the Wall Fitting

and screw Adapter by hand into the dedicated

line. Turn until tight.

WALL ADAPTER

INSTALLED

QUICK

LOCK

PEG

QUICK DISCONNECT

O-RING

5. Take the Wall Fitting and Twist Lock the Wall Fitting

into the Wall Adapter 1/4 turn and pull out, to a

snug fit. Once the Wall Adapter is secure, you

can now twist lock and unlock to remove Wall

Fitting with ease from the Wall Adapter.

E. Cutting the Feed Hose

The Hose assembly comes in 5 sections now

covering approximately 30 ft. of the pool, which

provides ample hose for most residential pools. The

Back-Up Valve is now 30 in. from the head cleaner

and should always remain this distance. For larger

pools see #14 on page 6 for instructions on Adding

Additional Feeder Hose.

1. Take Feeder Hose out of box (it will be

approximately 30 feet long). Before installing

the unit, you should lay the feed hose out straight

in the sun, (for one day if possible). The hose has

been curled up in the box and sometimes will go

around in a circle. If this happens, take the first or

second section of hose from the wall and reverse

it, (turn it around). You might have to reverse both

sections to correct the problem. Make sure the

feed hose is cut and installed properly.

2. Measure how deep your pool is by using your

telepole or the clear end of the feeder hose.

Cut the clear (soft) hose equal to the depth of your

pool. (Hint: the grate or domed main drain at

the bottom is usually the deepest point.)

Example: The clear (soft) hose is 10 ft. long, if the

pool is 8½ ft. deep, cut 1½ ft. off of the clear (soft)

hose. If the depth is greater than 10 ft., do not cut

the clear (soft) hose.

Deepest End of Pool

Telepole / Clear (Soft) Hose

Measure and Mark the Water Level

Main Drain

LEGEND® PLATINUM INSTALLATION MANUAL

7½ FT.

EXAMPLE DIMENSION

(Your Measurement May Differ)

NOT TO SCALE

MARKED SWIVEL

FARTHEST POINT OF POOL PERIMETER

FROM WALL FITTING

STEPS

1. With the feed hose assembly attached to the pool wall, hold the feed hose assembly

by the opposite end with the clear hose and walk the perimeter of the pool to locate

the farthest point on the perimeter from the wall fitting without stretching the hose assembly.

2. Measure the distance that the hose assembly extends beyond the pool perimeter

farthest point located in Step 1 — (7½ ft. in this example).

3. Cut half of the length obtained from Step 2 — (3¾ ft. in this example),

equally from each of the 10 foot lengths of white or grey hose on either

side of the marked swivel.

10 FOOT

WHITE OR GREY

HOSE SECTION

10 FOOT

WHITE OR GREY

HOSE SECTION

10 FOOT

SOFT HOSE

BACK UP

VALVE

REMOVE EXCESS MATERIAL

FROM HOSE ON EITHER SIDE OF

MARKED SWIVEL AS DESCRIBED

IN STEPS 2 AND 3.

WALL FITTING

SWIVEL

FLOATS

EXAMPLE OF HOSE ASSEMBLY

BEFORE CUTTING TO LENGTH

EXAMPLE OF FINISHED HOSE ASSEMBLY

AFTER CUTTING TO LENGTH

WHITE OR GREY

HARD HOSE SECTION

MARKED SWIVEL

END OF

SOFT HOSE

(End remains 30 in.)

SOFT HOSE

(Cut to your pool depth)

BACK UP VALVE FURTHEST POINT

OF POOL PERIMETER

FROM WALL FITTING

STEPS

4. Reassemble the hoses using the supplied mender nuts

as shown in

FIGURE 1

5. Your complete finished hose assembly should look like this.

The end of the 30 inch clear hose should reach just to the

furthest edge of the pool perimeter as shown.

WHITE OR GREY

HARD HOSE SECTION

FIGURE 1

WHITE OR GREY

HARD HOSE SECTION

(WALL FITTING SIDE)

WHITE OR GREY

HARD HOSE SECTION

(CLEANER SIDE)

MARKED SWIVEL

LEGEND® PLATINUM INSTALLATION MANUAL

7. Re-assemble the hoses and the swivel using

mender nuts (see Figure below, Step 1). Put

mender nut on swivels first, then push hose over

swivel (see Figure below, Step 2). Rotate mender

nut over hose clockwise until tight. Note: Keep

as many floats as possible on the long feed

hoses, spaced evenly apart to hold hose up

on top of water.

FEED

HOSE

MENDER

NUT

BARB ON SWIVEL

OR LEGEND

STEP 1

STEP 2

STEP 3

PUSH HOSE OVER BARB

PUSH MENDER NUT TOWARD HOSE AND ROTATE

CLOCKWISE BY HAND UNTIL TIGHT

SMALL END

OF MENDER

NUT AWAY

FROM HOSE

E. Cutting the Feed Hose - (cont.)

3. Lay the telepole next to the clear (soft) hose. If

the clear (soft) hose is longer than the mark on

the telepole, cut the excess from the end attached

to the white (hard) hose. Do not cut off the float.

Leave the first float in position next to the

Back-Up Valve. Place the second float midway

between the first float and the Hose Swivel.

4. Attach feed hose to the wall fitting and attach to

the pool wall. Hold the end of the 30 in. clear (soft)

hose and walk the perimeter of the pool keeping

the hose straight (do not stretch hose) to find the

farthest point of the pool from the wall fitting.

5. Measure the excess length between the farthest

point of the pool from Wall Fitting and the end of

30 in. clear (soft) hose.

6. Half of this measured length to be cut equally

from the 10 ft. long hoses next to the Marked

Swivel. (Example: Half of 6 ft. = 3 ft. each). If you

are cutting more than 2 ft. off the hoses, remove

the floats next to the Marked Swivel from both

hoses. See Figures on page 4.

Water Level

White (Hard) Hoses Swivel

Cut and Remove the

Excess Hose Length Cut Clear (Soft) Hose Equal to

the Deepest Pool Water Level

Telepole / Clear (Soft) Hose

LEGEND® PLATINUM INSTALLATION MANUAL

E. Cutting the Feed Hose - (cont.)

8. When cutting hoses, please use strong scissors

or a sharp knife. Be sure to slide the floats out of

the way when cutting hose.

9. Put extra mender nut on the Legend®Platinum

mast and push soft hose gently over mast at

1/2 in., turn mender nut around soft hose tight.

Note: The Back-Up Valve still should be 30 in.

from the head of the cleaner.

FEED HOSE

MENDER NUT

FEED MAST

SWIVEL

10. Now take the bag, EU16, out of the box and firmly

twist lock the bag onto the top of the Legend®

Platinum throat over rubber debris valve.

11.Review and check list: Hoses cut properly and

floats evenly spaced. Mender nuts tight around

swivels, back up valve, Legend®Platinum mast

and wall fitting. Make sure wall fitting is securely

locked into place.

12.Lower your complete Legend®Platinum

assembly into your pool carefully. It should look

like figure below.

13.Go back to your equipment and turn filter pump

on first (wait 30 seconds to force air out of the

hose), then turn booster pump on.

14.For large pools requiring more hose length you

will need to purchase one (1) additional hose

(LLD45-White or LLD45PM-Gray), four (4) floats

(ED10P-White or LLD10PM-Gray), one (1) swivel

(ED05-White or LLD05PM-Gray), and two (2)

mender nuts (ED15-White or LLD16PM-Gray).

Attach extra hose between long hoses using

floats, swivel and mender nuts. Divide extra hose

overage by three (3) this time to keep all hoses

the same length.

FIRST

SWIVEL

SECOND

SWIVEL THIRD

SWIVEL

SHORT

WHITE

HOSE

LONG

WHITE

HOSE

LONG

WHITE

HOSE BACK UP

VALVE

CLEAR

HOSE

Inhaltsverzeichnis

Andere Pentair Schwimmbadroboter Handbücher

Pentair

Pentair WARRIOR SI Bedienungsanleitung

Pentair

Pentair GREAT WHITE II Bedienungsanleitung

Pentair

Pentair Legend LL505G Bedienungsanleitung

Pentair

Pentair POOLSHARK Bedienungsanleitung

Pentair

Pentair POOLSHARK Bedienungsanleitung

Pentair

Pentair MiniMax 100 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY PROWLER 820 Bedienungsanleitung

Pentair

Pentair BLUESTORM Bedienungsanleitung

Pentair

Pentair BLUEFURY Bedienungsanleitung

Pentair

Pentair PROWLER 920 Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY WARRIOR Bedienungsanleitung

Pentair

Pentair Kreepy Kruiser Bedienungsanleitung

Pentair

Pentair GW9500 Bedienungsanleitung

Pentair

Pentair REBEL Bedienungsanleitung

Pentair

Pentair MAKOSHARK Bedienungsanleitung

Pentair

Pentair SandShark Bedienungsanleitung

Pentair

Pentair POOLSHARK Bedienungsanleitung

Pentair

Pentair pool cleaner Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY Bedienungsanleitung

Pentair

Pentair Kreepy Krauly Platinum Bedienungsanleitung

Pentair

Pentair KREEPY KRAULY E-Z VAC Bedienungsanleitung

Pentair

Pentair PROWLE 917 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung

BWT

BWT BC 30 Bedienungsanleitung

Maytronics

Maytronics Dolphin Triton Ps Bedienungsanleitung