Pentair ONGA PANTERA P221 Bedienungsanleitung

PANTERA

OWNER’S

MANUAL

HIGH-RATE SAND FILTER

Pantera High-Rate Sand Filter Owner’s Manual 1

General Information 2

Model Data 3

Installation & Assembly 4 - 8

Startup / Operation 9 - 10

Service & Maintenance 11 - 12

Tank Assembly 13

Troubleshooting 14 - 15

TABLE OF CONTENTS

Pantera High-Rate Sand Filter Owner’s Manual

This lter is designed for use in domestic/residential swimming pool installations with

correctly sanitised fresh or salt chlorinated water. Suitable for use with sand or Zelbrite

lter media.

1. Locate the lter system as close to the pool as practical.

2. Place the lter on a level stable foundation, preferably a concrete pad or paving.

3. Position all equipment to provide ease of access for future

servicing.

4. Protect the lter and pump from weather and direct sunlight by

ensuring that they are properly housed.

5. Ensure there is sucient space to provide adequate ventilation to

electric pump motor.

6. Clean a new pool as well as possible before lling pool and

operating lter. Excess dirt and large particles of foreign matter in the system can

cause serious damage to the lter and pump.

7. Ensure pump is compatible with lter specications.

GENERAL INFORMATION

Pantera High-Rate Sand Filter Owner’s Manual 3

The operator must be provided with the owner’s manual. This must be read before

operation and followed during operation. These instructions are a guide only. Users not

familiar with pool equipment should seek advice for suitably qualied persons with

experience in pool equipment installation.

Manufactured in Australia, the Onga Pantera II sand lter is made from UV stabilised

polyethylene. The reputation of durability and performance makes the PanteraII range

rst choice for quality pool builders.

Technical Data

P221 P225 P229 P233

Filter Diameter (mm) 535 635 735 835

Filter Area (m2) (Internal) 0.205 0.293 0.397 0.517

Max Working Pressure (kPa) 250 250 250 250

Maximum Flow Rate (lpm) 165 235 320 415

Design Flow Rate (lpm) 145 205 280 365

Min Flow Rate for Backwashing (lpm) 125 175 240 310

Recommended Pool Volume (litres):

Minimum 30000 45000 60000 75000

Maximum 65000 90000 120000 160000

Filter Height (to top of valve)* 840 960 1090 1170

Required mass of lter media:

Sand (16/30 grade) (kg) 90 140 185 220

Zeolite (kg) 70 105 140 165

Valve Size (connection to PVC) (mm) 40 40 50 50

Glass (Fine/Coarse) 60/30 90/45 120/60 135/75

*It is recommended to ensure there is at least 600mm of clear space above the top of the lter to facilitate servicing.

MODEL DATA

Due to excessive cycling, this lter is not suitable

for use on inbuilt In-oor Cleaning Systems.

Pantera High-Rate Sand Filter Owner’s Manual

INSTALLATION & ASSEMBLY

Hazardous Pressure

Incorrectly installed or tested equipment may fail, causing severe injury

or property damage. Read and follow instructions in owner’s manual when

installing and operating equipment.

Have a trained pool professional perform all pressure tests.

All glued ttings and pipe work should be allowed to dry to atmosphere for

24 hours before closing the installation. Failure to do so could cause injury

or installation failure.

The ttings on these lters are constructed of ABS. Some PVC jointing

compounds are incompatible with ABS possibly causing failure to the

product. Check compound suitability prior to use.

WARNING

HAZARDOUS Pressure!

Can cause severe injury

or major property damage

from tank explosion.

Filter pumps require

hazardous voltage which

can cause shock, burn or

even death.

Disconnect power to

motor.

1. Stop pump.

2. Release all pressure

from system by turning

valve handle to waste.

BEFORE WORKING

ON THE FILTER

BEFORE WORKING ON

PUMP OR MOTOR

Pantera High-Rate Sand Filter Owner’s Manual 5

INSTALLATION & ASSEMBLY

Installation & Assembly of Internal Components

Installation of lter should be only carried out by qualied personnel. Ensure that the

under-drain assembly (hub, laterals & tube) are properly assembled & installed prior to

adding lter media (sand).

1. The lter internals comprise of a collector hub and eight (8) laterals,

which are supplied packaged seperately with the collector hub and are stored inside

the lter tank prior to shipment.

2. Carefully inspect the laterals and hub prior to assembly for any

visible defects.

3. To assemble the laterals and hub please use the following steps. (The connection

between the hub and the lateral is completed inside the lter tank - refer to diagram

on following page)

For P221100 & P225100 Models only:

Push in and align the male tab on the lateral with the female slot in the hub. Rotate the

lateral clockwise until the tabs engage with an audible “click”. Repeat this process for all 8

laterals.

For P229200 & P233200 Models only:

Place the hub inside the neck of the lter tank. Begin by assembling the ‘F’ pieces, align

the lateral key with the hub and insert, turn to lock in place. Repeat with the 4 ‘F’ pieces.

Next, insert the large diameter laterals in the outer socket of the ‘F’ pieces. Repeat 4

times. Finally, insert the small laterals into the inner sockets. Repeat 4 times.

Hub Lateral Model

P229 & P233

Hub Lateral Model

P221& P225

Important: Ensure slotted side of laterals face downwards from hub after nal assembly, and prior to lling with sand.

2016 Onwards

Pantera High-Rate Sand Filter Owner’s Manual

INSTALLATION & ASSEMBLY

Steps for Installation of Filter Internals

A. Insert rst lateral into socket; twist

clockwise 1/4 turn to lock lateral into

hub.Lateral is correctly installed

when slots face down.

B. Insert assembly into

top of lter tank.

C. Hold assembly up near top

of tank and add remaining

laterals.

D. After all laterals

are securely

in sockets,

position

assembly in the

centre on the

bottom of the

tank.

Pantera High-Rate Sand Filter Owner’s Manual 7

Loading Sand Media

1. To keep sand out off collector assembly, place

plastic sand shield over top of collector tube before

pouring sand into lter (See diagram).

2. To support laterals and prevent lateral breakage

during loadings, ll tank about half full of water

before loading sand.

3. Pour sand into lter, making sure that the sand is of

the correct type and quantity for the particular lter

model (Refer to lter label).

INSTALLATION & ASSEMBLY

Make sure gasket area on top of tank is free of

sand before installing valve.

4. Before installing valve, double-check that the correct quantity of sand has been

loaded.

5. Remove plastic sand loading shield and keep for future use.

Installation of Multi-Port Valve

1. Install o-ring on valve ange; make sure o-ring is clean, and has no nicks, tears, or

scrapes and lubricate with silicon based lubricant.

2. Make sure tank and valve anges are clean and free of sand; put valve on top of tank.

Vertical pipe of collector assembly inserts into base of valve.

3. Install clamp; make sure knob is positioned for easy access for lter maintenance.

Valve port labelled “Pump” should point toward pump.

Pantera High-Rate Sand Filter Owner’s Manual

4. Tighten clamp knob until clamp ends (under bolt) are 1/4” (6mm) apart.

Tap around outside of clamp with a mallet to help seat clamp.

5. Connect pipe from pump discharge to valve port labelled “PUMP”; use union half

provided. Assemble union as follows for leak free operation:

- o-ring and sealing surfaces must be clean.

- Assemble hand tight only (No wrenches).

- NO pipe compound or teon tape on unions.

6. Complete all plumbing connections, using 1 1/2” (P221100 & P225100) or 2” (P229200

& P233200) pipe to reduce pressure losses as much as possible.

- Pipe from valve RETURN port to pool return.

- Pipe from valve WASTE port to waste.

- Suction piping from pool to trap inlet on pump.

7. System is ready to start up.

8. If you notice a leak around the clamp area after

15-30 minutes of running, repeat steps 3-4.

Hazardous pressure. Clamp will not hold unless it is

seated properly! DO NOT START PUMP until clamp ends

are 1/4” (6mm) apart or less.

INSTALLATION & ASSEMBLY

If there are leaks from beneath valve/

clamp area, STOP PUMP, release all

pressure by turning valve handle to

‘waste’, remove clamp and valve and

clean sealing surfaces.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pentair Wasserfiltersystem Handbücher

Pentair

Pentair EVERPURE H Series Bedienungsanleitung

Pentair

Pentair BIOSHIELD 522635 Bedienungsanleitung

Pentair

Pentair PRF-RO Handbuch

Pentair

Pentair EZ-RO 200/2G-BL Original Betriebsanleitung

Pentair

Pentair EVERPURE Twin Betriebsanleitung

Pentair

Pentair Eclipse 58920100 Bedienungsanleitung

Pentair

Pentair FC Series Betriebsanleitung

Pentair

Pentair AQUATIC ECO-SYSTEMS ARIAS 6000 Bedienungsanleitung

Pentair

Pentair EVERPURE H-300 Bedienungsanleitung

Pentair

Pentair PRESHPOINT GRO-350BP Bedienungsanleitung

Pentair

Pentair Posi-Chlor-15 Bedienungsanleitung

Pentair

Pentair FRESHPOINT U440 Bedienungsanleitung

Pentair

Pentair SHURFLO WB6-M3-22-003-SS Bedienungsanleitung

Pentair

Pentair MYERS PUMP VAULT Handbuch

Pentair

Pentair FLECK 5810 SXT Bedienungsanleitung

Pentair

Pentair freshpoint F1000-DFB Bedienungsanleitung

Pentair

Pentair PENTEK US-1000 Bedienungsanleitung

Pentair

Pentair OMNIFILTER F2000-B2B Bedienungsanleitung

Pentair

Pentair EVERPURE MRS-350BL Bedienungsanleitung

Pentair

Pentair TRITON NEO Bedienungsanleitung

Pentair

Pentair Cristal-Flo Bedienungsanleitung

Pentair

Pentair OMNIFILTER U25 Bedienungsanleitung

Pentair

Pentair Everpure QL2-OW200L Bedienungsanleitung

Pentair

Pentair PDF-1000VF-P Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung

Renfert

Renfert 2940-0000 Bedienungsanleitung