People Power Press FLEX2000 Bedienungsanleitung

FLEX2000

BUTTON MACHINE

USER MANUAL

button machines • button parts • custom buttons

MULTI-SIZE

BUTTON

PRESS

DIE TABLE (TOP VIEW)

SHALLOW PICKUP DIE DEEP PICKUP DIE

(Insert Button Shell - Left Side) (Insert Pinback - Right Side)

CRIMP DIE

HANDLE

ANATOMY OF YOUR FLEX2000

1. Button Press

2. Die Set a) Shallow Pickup Die*

b) Deep Pickup Die*

c) Crimp Die*

3. Plastic Insert Ring (for some of the add-on sizes)

*Every button size requires it’s own DIE SET (shallow pickup die, deep

pickup die and crimp die). Be sure to keep your die sets organized and use

parts/supplies of the same size.

TO MAKE A BUTTON YOU WILL NEED:

Pinback button making parts:

2c.

2a. 2b.

CHANGING THE DIE SET:

A. Removing the dies:

A1. To swap the die set: Remove the pickup dies rst. Slide

the die table all the way to the right side and simply lift out

the shallow pickup die. Repeat on the left to remove the

deep pickup die.

A2. Once both pickup dies have been removed, hold the crimp

(top) die rmly and pull down. The pin holding it in

place will slide out of the button press.

B. Replacing the dies:

B1. First replace the crimp (top) die by sliding the post back

into the button press.

B2. Slot the pickup dies into the holes on either side of the

die table. Make sure the shallow die is on the right and the

deep die is on the left. Make sure that. The small post on

either side of the die table inserts into the hole at the base

of the die.

LIFT

PULL

LIFT

PULL

LIFT

PULL

A1. A2.

B2.B1.

USING THE ROTARY CUTTER

1. Place your printed sheet of artwork on top of a cutting surface

such as a cutting mat or board. Softer surfaces (like cutting

mats) have more give and traction and will work better than

harder surfaces (like glass)

2. Center the corresponding size rotary cutter on top your sheet

of artwork and line up the blade with the edge of your

printed artwork.

3. Push down and apply even pressure on the handle and rotate

to rotate the blade 360 ° to cut out your artwork.

HANDLE

(SIDE VIEW)

(BOTTOM VIEW)

BLADE

(TOP VIEW)

ROTATE

HANDLE

Before you start:

Place the button maker in front of you, with the dies easily

accessible, on a solid table so that the machine doesn’t shift.

You may want to use the holes in the base to secure your button

maker onto a wooden board for added stability.

Make sure that the appropriate size of dies are inserted into the

table and that the matching (top) crimp die has been slotted

into place.

*Match your button parts to the die set you are using.

If you are using the 2.25” die set - insert the plastic insert ring

into the deep pick-up die before you begin.

MAKING A BUTTON

1. Set up the button maker so that the die table is facing you.

The shallow pick-up die should be on the left side and the

deep pick-up die should be on the right side.

HANDLE

CRIMP DIE

(TOP)

(TOWARDS YOU)

SHALLOW PICK-UP

DIE (LEFT)

DEEP PICKUP DIE

(RIGHT)

TABLE SLIDES

SIDE TO SIDE

1a. Place a shell in the SHALLOW DIE (LEFT) The edge of the

shell slots into the round channel in the die. The shell should

t exactly into the slot.

1b. Place your cut-out artwork over the shell. It should t snugly

in the available space.

1c. Place a piece of mylar on top of your artwork.

1d. Place the pinned-back into the DEEP PICKUP DIE RIGHT

it should sit snugly in the depression in the die. Make sure the

pin is aligned the same way as your artwork. The hook and

pin side of the back should be facing down.

1. Get Your Button Parts Ready

PLASTIC INSERT

RING

(2.25” only)

MYLAR

ARTWORK

SHELL

SHALLOW

PICK-UP DIE

DEEP

PICK-UP DIE

INSERT PINNED BACK

PIN SIDE DOWN

*If you are making 2.25” buttons the white plastic insert ring must be placed

in the deep pickup die before the pinned-back.

**For best results, use the post on the back of the dies to orient your artwork,

if you point the top of your both artwork and the top of your pinned back

towards these posts your buttons will come out right side up!

(for some add-on sizes)

2a. Slide the die table all the way to the right so that the

shallow pick-up die (with your shell and artwork in it) is

centered under the press. The die should align with the crimp

die (top).

2b. With the die table facing you, pull the handle down towards

you. You will note with the rst press that you feel the die

depress as it picks up your button. No force is necessary, just

pull the handle down as far as it goes.

2. Pressing the button (step 1):

SLIDE

PULL

2a. 2b.

3. Pressing the button (step 2):

3a. Slide the die table all the way to the left so that the deep

pick-up die with your pinned back in it, is centered under the

press. The die should align with the crimp die (top).

3b. Pull the handle down towards you like before. It will not pull

down as far as it did during the rst pressing.

SLIDE

PULL

4. Slide the die table back to the left and remove your

nished button. AND ENJOY!!

Andere People Power Press Elektrowerkzeuge Handbücher

People Power Press

People Power Press FLEX1000 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch