Pepperl+Fuchs RocketLinx ICRL-U-5RJ45-G-DIN Bedienungsanleitung

Quick Installation Guide

DOCT-6559 | Release Date- February 2020

ROCKETLINX

ICRL-U-5RJ45-G-DIN

ICRL-U-4RJ45/SFP-G-DIN

Electronic.indd 1 12/4/2019 9:16:57 AM

Introduction

ICRL-U-5RJ45-G-DIN and ICRL-U-4RJ45/SFP-G-DIN are a compact

size Ethernet unmanaged Gigabit switches, which ensure high

switching performance and easy installation. Along with its high

switching performance, it supports multiple internal performance

features, such as 9K bytes Jumbo Frame, Flow Control, and it ensures

quality trac transmission.

The ICRL-U-5RJ45-G-DIN provides ﬁve 10/100/1000T(X) RJ45 ports.

The ICRL-U-4RJ45/SFP-G-DIN provides four 10/100/1000T(X) RJ45

ports and one 1000BASE-F(X) SPF port.

The switch provides a rugged metal case design (IP31) to operate in

harsh environments (-40 to 75°C).

It features one relay output to alarm users if power fails.

Wiring the Power Inputs

The switch provide power redundancy and polarity reverse protection.

Use a UL Listed power supply with a recommended working voltage of

24VDC with an input range of 10-60VDC.

PWR1 and PWR2 are dual power inputs that can be connected to

power sources simultaneously. When the primary power source fails

(PWR1), the system automatically switches to the secondary power

source (PWR2), preventing any power interruption.

Both of PWR1 and PWR2 support positive electricity and negative

electricity power systems. Please notice the power system for PWR1

and PWR2 only accept either positive or negative electricity power

system at one time

Electronic.indd 2 12/4/2019 9:16:57 AM

1. Insert the positive and negative wires into the V+ and V- contact

on the terminal block connector.

2. Tighten the wire-clamp screws to prevent the power wires

loosened.

Wiring the Relay Output (DO)

The relay output contacts are in the middle of the terminal block

connector as shown below. Insert the wires as show below to connect

the relay output alarm so that it detects power fault and avoids

forming a short-circuit.

Note: The relay contact only support 1A current, 24VDC.

Pepperl+Fuchs does not recommend apply higher voltage and current

that over this speciﬁcation.

Electronic.indd 3 12/4/2019 9:16:57 AM

Connecting to Network

Connect one end of an RJ45 Ethernet cable into the UTP port of

switch, while the other end is connected to the attached networking

device. The UTP port supports the auto MDI/MDIX function.

Ethernet cables are categorized into unshielded twisted-pair (UTP)

and shielded twisted-pair (STP) cables. Category 3, 4, 5 Ethernet

cables are suitable for systems with 10 Mbps transmission speed.

For systems with 100/1000 Mbps transmission speed, Category 5e or

Category 6 Ethernet cables are the only suitable speciﬁcations for this

environment. Also make sure that the distance between each node

cannot be longer than 100 meters (328 feet).

The ICRL-U-4RJ45/SFP-G-DIN SFP port

supports hot-swapping and you can change

the SFP ﬁber transceiver without system

power o. This feature is useful for ﬁeld

site installations if the ﬁber signal cannot

attach the other end device - just change

to a dierent SFP transceiver type with

larger power launch power budget. The SFP port accepts a standard

Gigabit MINI GBIC SFP transceiver. Plug in the SFP transceiver and

cross-connect the transmit channel at each end to receive channel at

the opposite end.

Electronic.indd 4 12/4/2019 9:16:57 AM

ATTENTION This is a Class 1 Laser/LED product. Do not look

into the Laser/LED beam.

LEDs

The LNK / ACT LED turns on for link up and blinks for packet transmit

and receive. The Speed LED turns on for Gigabit link and turns o for

10/100Mbps link.

LED Color Function

P1, P2 Green Power (1,2) on

P-F Red Power failure (1 or 2)

1-5

(ICRL-U-5RJ45-G-DIN)

1-4

(ICRL-U-4RJ45/SFP-G-DIN)

Green Link

Flashes Green Activity

Amber Gigabit speed

SFP

(ICRL-U-4RJ45/SFP-G-DIN)

Green Link

Flashes Green Activity

Grounding the Switch

There is one grounding screw on the bottom side of switch. Connect

the earth ground screw of the switch to the grounding surface to

ensure safety and prevent noise.

Electronic.indd 5 12/4/2019 9:16:57 AM

Mounting the Switch

You can mount the switch on a DIN rail. The

DIN rail clip is attached to the switch, which

supports the EN 50022 DIN Rail standard.

1. Insert the upper end of DIN rail clip into

the back of DIN rail track from its upper

side.

2. Lightly push the bottom of DIN rail clip

into the track.

3. Verify that the DIN rail clip is tightly

attached on the track.

Electronic.indd 6 12/4/2019 9:16:57 AM

Customer Service

You can use one of the following methods to contact Pepperl+Fuchs.

Worldwide Headquarters

Pepperl+Fuchs AG

68307 Mannheim, Germany

+49 621 766-0

[email protected]

USA Headquarters

Pepperl+Fuchs, Inc.

Twinsburg, Ohio 44087 - USA

+1 330 425 3555

[email protected]

Asia Paciﬁc Headquarters

Pepperl+Fuchs Pte Ltd.

Company Registration No.199003130E

Singapore 139942

+65 6779 9091

[email protected]

Electronic.indd 7 12/4/2019 9:16:57 AM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pepperl+Fuchs Schalten Handbücher

Pepperl+Fuchs

Pepperl+Fuchs LVL-M4 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ARS B2 IC Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiC2832R1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LVL-M3 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LVL-M4 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs RocketLinx ICRL2-U-16RJ45-G-DIN Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs Vibracon LVL-M Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HD2-GTR-4PA Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LVL-M4 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs SI00114O-H Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs Vibracon LVL-M2C Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs Ethernet-APL Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LKL-P1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs Vibracon LVL-M1H Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs Vibracon LVL-M1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs RocketLinx ICRL2-U-5RJ45-DIN Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VISOLUX ML7-55 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs RocketLinx ICRL2-U-8RJ45-DIN Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ARS B2 IA Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LCL1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD0-SD2-Ex2.1045 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LVL-M4 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs LVL-M4 Handbuch

Pepperl+Fuchs

Pepperl+Fuchs Vibracon LVL-M H Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung