Perle IDS-710HP Bedienungsanleitung
IDS-710HP Switches Quick Start Guide P/N: 5500457-10 Version #01.02.2020
IDS-710HP
Quick Start Guide
___________________________________________________
This guide covers basic installation and configuration and is intended for first
time setup or product evaluation.
Complete details can be found in the following guides at
www.perle.com/downloads.
IDS-710HP (-XT) Hardware Installation Guide
IDS Managed PoE+ Switches User Guide - PRO Feature Set
IDS Managed PoE+ Switches CLI Reference Guide - PRO Feature Set
What’s in the box?
The IDS switch
Quick Start Guide (this document)
Hardware Overview
Front View Back View
1 – Reset/FS (Fast Setup)
2 – Status LEDs
3 – Digital Inputs/Relay I/O
4 – SFP status LEDs
5 – Console port – Micro USB
6 – SFP slots
7 – 10/100/1000Base-T, PoE
capable, Ethernet ports
8 – Terminal block for power 1
and 2
9 – Wall mount bracket screw
holes
10- DIN rail clip
11- Ethernet port LED1
12
-
Ethernet port LED2
IDS-710HP Switches Quick Start Guide 2
Wiring the Terminal Block
Connecting the switch to ground (optional)
If your installation requires additional grounding, refer to the Hardware
Installation Guide for information on connecting ground.
Connecting power to the IDS switch
You may connect both sets of power inputs to provide redundant power.
1. Ensure the power source is off prior to connection.
2. Using a pair of 12-16AWG wires, strip them both 7-8mm (5/16”).
3. Loosen the terminal block screws and connect positive (+) / negative (-)
wires in the +/- terminals.
4. Tighten terminal screws (0.51Nm torque). Ensure the wires are securely
fastened.
5. Re-insert the terminal block connector if removed. Turn power on at
source. Check LED indicators for status.
6. Connect P2 (power source 2, beginning at Step 1.
For complete wiring instructions and for all Hazardous Locations and
general safety warnings consult the Hardware Installation Guide.
Connecting PoE/PoE+/PoE++ devices
Supports IEEE 802.3af, IEEE 802at and IEEE 802.3bt standards
For PoE devices up to 15.4 watts per port
For PoE+ devices up to 30 watts per port
For PoE++ devices up to 100 watts per port
Connecting Ethernet
Connect network or devices to Ethernet ports (1- 8) using Cat5/5e Ethernet
cables
IDS-710HP Switches Quick Start Guide 3
LED Indicators
(For detailed information refer to the Hardware Installation Guide)
PWR (Power Inputs)
Green – P1 and P2 Power inputs are within specifications
Orange – P1 or P2 not providing power within specifications
Red – Neither P1 or P2 providing power within specifications
SYS (System status)
Green blinking – System booting
Green solid – System operating normally
Green blinking slowly – Fast Setup mode activated, port available
Green blinking fast – Fast Setup mode activated, no port available
Red – Hardware fault or firmware load error.
ALR (Alarm)
Off – No alarms configured
Green solid – Alarms configured but no alarms detected
Red solid – Alarm condition detected
Red blinking – Alarm condition detected and Alarm Relay activated
Ethernet Port Link / Speed
1000 Mbps – LED1 on, LED2 off
100 Mbps – LED1 on, LED2 on
10 Mbps – LED1 off, LED2 on
On solid – Port Link
Random blinking – Activity
Slow steady blinking – Error Disabled
Rapid blinking – Port is in Fast Setup mode
SFP LEDs
Off – No Link
Green – Fiber link established
Green flashing – Link/Activity
IDS-710HP Switches Quick Start Guide 4
Fast Setup
Fast Setup provides a simple method of doing an initial setup from a PC. It only
requires a PC Ethernet connection and a web browser. Other methods to
configure the IDS Switch can be found in the IDS Switch User’s guide.
1. Your PC must be set to obtain an IP address automatically using DHCP (See
Control Panel ->Network and Sharing Center -> Change adapter settings -
>Local Area Connection Properties ->Internet Protocol Version (TCP/IPv4) -
>Properties ->Select Obtain an IP address automatically.
2. Press and hold the reset button (1) on the switch for 4 seconds and then
release it. Use of a small tool such as a paper clip will be required. The
yellow and green LEDs on an unused RJ-45 connector will flash rapidly to
indicate where to plug in the Ethernet cable from your PC.
3. Using a web browser, enter to a well known webpage such as
www.google.com, you will be automatically directed to the IDS Get Started
screen.
Note: Alternatively type in 169.254.0.1 into the browser’s address bar.
4. Once connected, fill in the required fields, apply changes to save and exit.
The configuration changes will be immediately applied to the switch.
5. The PC can now be reset to its normal network address and the switch can
be accessed using the conventional IP addressing.
© 2020 Perle Systems Limited. All rights reserved.
Andere Handbücher für IDS-710HP
1
Andere Perle Schalten Handbücher
Perle
Perle IDS-509FPP Handbuch
Perle
Perle IDS-105FE Series Bedienungsanleitung
Perle
Perle IDS-105G Bedienungsanleitung
Perle
Perle IDS-409 Bedienungsanleitung
Perle
Perle IDS-305G Handbuch
Perle
Perle IDS-206 Handbuch
Perle
Perle IDS-509G2PP6 Handbuch
Perle
Perle IDS-710 Handbuch
Perle
Perle IDS-205F Bedienungsanleitung
Perle
Perle IDS-108FPP series Bedienungsanleitung
Perle
Perle IOLAN SDG1 W Handbuch
Perle
Perle IDS-105F Bedienungsanleitung
Perle
Perle IDS-509CPP Handbuch
Perle
Perle IDS-509PP8 Bedienungsanleitung
Perle
Perle IDS-409C Handbuch
Perle
Perle IDS-509F2 Handbuch
Perle
Perle RPS830 Bedienungsanleitung
Perle
Perle IDS-509PP Handbuch
Perle
Perle IDS-205 Bedienungsanleitung
Perle
Perle 07012410 Handbuch
