Perlegear PGSS7 Bedienungsanleitung
Model: PGSS7
Speaker Floor Stand
Instruction Manual V2.0
Thank you for choosing this Perlegear product! At Perlegear we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
[email protected](US/CA)
IMPORTANT SAFETY INFORMATION
Tools Needed (Not lncluded)
• Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
• Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
• Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
• Please note: Not all hardware included in this package will be used.
• This product may contain moving parts. Use with caution.
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
Philips Screwdriver
Supplied Parts STEP 1 Attach the nails or rubber pads to the base feet
Supplied Hardware
Base x2
01
Post Extension x2
02
Post Assembly x2
03
90 Degree Plate x2
04
Square Plate x2
05
Narrow Plate x2
06
x6
C
x2
D
x2
E
x2
F
x6
A
A
B
x6
B
Bolt
1/4″ x13.5mm
x4
P
Washer
#6 x #14
Nail Nut Pad Sponge Plastic Nut
x4 x4
I J
x4
K
x2
G
x4
H
Washer
M4/M5
Bolt
M5x8mm
Bolt
M5X12mm
Bolt
1/4″x12mm
Bolt
M4X12mm
OPT
A
OPT
B
B
For marble or wooden floor, rotate
and insert the rubber pads into the
holes of the base.
For carpets floor, screw the nails
into the holes of the base.
x2 x2
N O
x4
L
x2
M
Washer
#6
Bolt
M6x12mm
Bolt
#6-32 x 1 1/4″
Nut
#6-32
01
C
01
- 1 - - 2 -
STEP 5 Route the cables
- 7 -
G
OPT
A
STEP 2A Fasten the post assemblies to the bases (for regular
lower height)
STEP 2B Fasten the post extensions and post assemblies to the
bases (for extra higher height)
- 3 - - 4 -
- 5 - - 6 -
01
03
01
02
The plastic packaging bag of the posts and bases come with yellow and blue
labels. ONLY assemble the posts and base labelled THE SAME COLOR.
Otherwise it will be difficult to assemble.
STEP 2B-1 Secure the post assem-
blies [03] to the post extensions [02]
STEP 2B-2 Fasten the post exten-
sions [02] and post assemblies [03]
to bases [01]
03
04
02
Loosen
Lift
Tighten
STEP 3 Adjust post assemblies to the desired height
STEP 4 Secure speaker to stand
Speaker option A: two thread inserts
Note: The washers
[K] are only suitable
for bolts [J] and [H] (If Needed)
06
E
H
K
I
JL
G
OPT
B1
04
Speaker option B1: keyhole insert
1. Insert bolt [F] through 90 degree
plate [04]
2. Thread plastic nut [E] to bolt [F]
3. Insert bolt [F] into keyhole and
fasten the plastic nut [E]
4. Use the washer [P] to adjust the
length of the bolt [F] if necessary.
04
E
P
F
Speaker option B2: keyhole insert
G
04
K
HJ
D
OPT
C
05
05
Speaker option C: Thread holes located at
thebottom of the speaker
OPT
B2
G
(Suitable for Samsung SWA-8500S,
SWA-9000S Speakers)
O
M
①
②
04
N
K
1.Slide the washer [O] into the bolt [M], then insert
them into the keyhole.
2.Tighten the nut [N] until the washer [K] is pulled
firmly against the 90 degree plate [04].
1.Slide the washer [O] into the bolt [M], then insert
them into the keyhole.
2.Tighten the nut [N] until the washer [K] is pulled
firmly against the 90 degree plate [04].
Andere Perlegear Sprecher Handbücher
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung