Perlick HD24 SERIES Bedienungsanleitung

INSTALLATION AND OPERATION INSTRUCTIONS

18” SHALLOW-DEPTH SERIES

IMPORTANT INFORMATION

To register your product, visit our web site at

(www.perlick.com). Click on “Commercial”, then

“Service”. You will see the link to “Warranty Registration

Form”. You must complete and submit this form or the

installation date will revert back to the ship Date.

This manual has been prepared to assist you in the

installation of your Cabinet and to acquaint you with

its operation and maintenance.

We dedicate considerable time to ensure that our

products provide the highest level of customer

satisfaction. If service is required, your dealer can

provide you with a list of qualified service agents. For

your own protection, never return merchandise for

credit without our approval.

We thank you for selecting a Perlick product and

assure you of our continuing interest in your

satisfaction.

8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414.353.7060 • Fax 414.353.7069

Toll Free 800.558.5592 • E-Mail [email protected] • www.perlick.com

Table of Contents

Introduction ................................................................ 1

Preparing the cabinet for use

General Precautions .................................................. 2

Installation Notes ....................................................... 2

Dimensions Diagram ................................................. 3

Preparing the Space .................................................. 4

Preparing Electrical Connections .............................. 4

Unpacking/Moving the Unit........................................ 5

Anti-tip Bracket Information ....................................... 5

Installation

Installation Instructions .............................................. 6

Shelving ..................................................................... 8

Door Panel Options ................................................... 8

Door Lock Installation ................................................ 9

Operation ................................................................. 10

Maintenance ............................................................ 11

Troubleshooting ....................................................... 12

PERLICK COMMERCIAL WARRANTY: This

Commercial Refrigerator comes with a five-year

compressor warranty and a one-year parts and labor

warranty (with the option to purchase a second year).

WARNING: When lifting, the full weight of the

cabinet must be supported. Lift from the cabinet

base and not from the top. Improper lifting can

result in severe damage to the cabinet.

Form No. Z2325

MODEL: HD24 SERIES

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

GENERAL PRECAUTIONS

DANGER

1. Risk of child entrapment. Before you throw

away your old unit, take off the doors and

leave shelves in place so children may not

easily climb inside.

2. Altering or cutting of the power cord, or

removal of the power plug, or direct wiring

can cause serious injury, fire and/or loss

of property and/or life and will void the

warranty.

WARNING

1. Never attempt to repair or perform

maintenance on the unit until the electricity

has been disconnected.

2. The anti-tip kit must be installed on this unit

before it is used. Never use the shelves or

doors as steps or to support more than they

are designed to support.

CAUTION

1. Do not lift unit by shelves or door handle.

2. Failure to clean the condenser every three

months can cause the unit to malfunction.

This could void the warranty.

3. Never install the unit behind closed doors

(ie; closets, small pantries, etc). Be sure

front louvered toe plate is free of obstruction.

Obstructing free air flow can cause unit to

malfunction and may void the warranty.

4. Use only Perlick replacement parts. Use of

non-Perlick parts can damage the unit, and

may void the warranty.

INSTALLATION INSTRUCTIONS

GENERAL

1. All electrical instructions assume that outlet is

located 4-10 inches from the floor.

2. Floor must be level in area of installation. Leg

levelers are used for fine-tune adjustment only

and should not be used to compensate for floor

differences exceeding 1/2”.

3. Install the anti-tip kit on the unit (see page 5 or

7.)

4. When moving unit into position, take care to

protect floor surface with cardboard, rugs, etc

(see page 4).

5. Never attempt to move unit without aid of at

least one other person.

6. Always secure doors shut prior to moving the

unit.

MINIMUM FINISHED ROUGH OPENING

REQUIREMENTS

1. Height: 32-1/8”

2. Depth: 18-1/4”

3. Width: 24”

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

3Form No.Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Figure 1. Dimensions

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

PREPARING THE SPACE

Make sure the installation opening is properly

prepared. Refer to Figure 1 (page 3) for space

dimensions.

CAUTION

If unit is to be installed under a countertop,

it is recommended that the countertop be

supported by a structure other than the unit

itself, to prevent damage to the countertop.

IMPORTANT: For a cabinet door to operate

properly, the door must be open a minimum of

94° (see Figure 1). Use a minimum 3-3/32” filler in

corner installations to ensure a 94° opening. Allow

enough clearance in front of the unit for full door

swing or shelf pull-out.

IMPORTANT: Make sure floor under unit is level

with the surrounding finished floor. Protect finished

floor with plywood, rug, cardboard or some other

suitable material before moving the unit into place.

Failure to do this may result in damage to the floor.

PREPARING ELECTRICAL

CONNECTIONS

A 115 volt, 60Hz, 15 amp circuit breaker and

electrical supply are required. A separate circuit is

recommended.

Follow the National Electrical Code along with

local codes and ordinances when installing the

receptacle.

All Perlick units come equipped with a NEMA

5-15P, 90° plug with a 5’ cord (minimum) extending

beyond the rear of the unit. The electrical outlet

must be flush with, or recessed into, the back wall

or located where the recess is on the back of the

cabinet (Figure 2).

DANGER

ELECTROCUTION HAZARD!

Electrical grounding required. This appliance

is equipped with a 3-prong (grounding)

polarized plug for protection against possible

shock hazards.

1. Never remove the round grounding prong

from the plug.

2. Never use a 2-prong grounding adapter.

3. Never use an extension cord to connect

power to the unit.

If a 2-prong wall receptacle is encountered,

or a longer power cord is required, contact

a qualified electrician to install the proper

3-prong receptacle in accordance with

applicable electrical codes.

DANGER

Failure to comply with the above electrical

guidelines may result in possible injury/death/

fire or loss of property.

Recessed

Panel

Figure 2. Electrical Connections

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

5Form No.Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Figure 2. Electrical Connections

ANTI-TIP BRACKETS

WARNING

Unit may tip forward if loaded racks/shelves

are all pulled out at the same time. To prevent

tipping and provide a stable installation, the

unit must be secured in place with the anti-tip

brackets provided with the unit.

A set of metal anti-tip brackets are supplied with the

unit. The anti-tip brackets, when properly installed,

should secure the rear legs and prevent the unit

from tipping forward. Select fasteners based on

the material the brackets will be fastened to.

Some installation sites may require modification

to provide a secure surface for attaching the

brackets. Refer to Figure 3 for mounting bracket

locations.

IMPORTANT: If installing on a concrete floor,

concrete fastners are required and are not included

in the Anti-Tip Kit.

UNPACKING AND MOVING THE UNIT

CAUTION

Do not cut cardboard sleeve covering the unit.

Cutting may result in damage to the exterior of

the unit.

1. Uncrate the unit on a flat level surface. Remove

the cardboard sleeve by removing the banding

holding the sleeve to the shipping base.

Carefully lift the cardboard sleeve up over the

top of the cabinet.

2. Carefully lift unit off base onto a hand truck or

dolly (this should be done with a minimum of two

people, larger cabinets may require additional

helpers). Make sure unit it is balanced on

transporting device. Secure unit to transporting

device using soft flexible strapping. Protect

cabinet surfaces with cloth material where

strapping contacts the unit.

3. Before moving unit, secure door to unit with

tape to hold the door closed.

Figure 3. Installing Anti-tip Brackets

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

INSTALLATION

CAUTION

Finished flooring should be protected with

appropriate material to avoid damage from

moving the unit.

If unit is built into cabinetry, allow clearance for

unit to be removed from opening for potential

service requirements.

If unit has been laid on its back or sides, place

unit upright and allow minimum of 24 hours

before connecting power.

1. Plug the unit into the 15 amp grounded outlet

located in the installation opening. With power

applied to the unit, check that lighting and

cooling function operate properly, then turn off

power to the wall outlet at the circuit breaker.

WARNING

Shut off power to the wall outlet before

installing unit into the opening.

2. Check that the following are level and square:

- front face and interior opening

- installation opening and floor surface

- countertop bottom front edge

IMPORTANT: The floor under the unit must be at

the same level as the surrounding finished floor.

3. If all surfaces are level, refer to Figure 3 and

perform the following:

A. Measure from the floor to the bottom of the

front edge of the countertop.

B. Measure the rear of unit cabinet from floor to

top of cabinet, at back corners.

C. Adjust rear legs so B measurement equals A

measurement. Using an adjustable wrench

or pliers, turn legs counterclockwise to raise

the unit or clockwise to lower the unit.

IMPORTANT: Leveling legs should not extend

more than 3/4” from bottom of unit.

4. Slide unit into position. Make sure the rear

levelling legs slide under the anti-tip brackets.

Push the unit into the opening until the door

is flush with the surrounding cabinetry, or

until the rear legs are tight against the anti-tip

brackets.

IMPORTANT: The rear levelling legs must be

engaged under the anti-tip brackets.

5. Shim the front of the unit so the front door is

flush with the surrounding cabinetry. Adjust

the front legs to support the countertop at

the shimmed height. Using an adjustable

wrench or pliers, turn legs counterclockwise

to raise the unit or clockwise to lower the unit.

Countertop should be resting on top of the unit.

IMPORTANT: The rear levelling legs must be

engaged under the anti-tip brackets.

CAUTION

The prevent damage to the countertop and

unit underneath, do not place heavy objects

on countertop directly above the unit.

6. Check interior door openings inside unit to

ensure unit is level.

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

7Form No.Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Figure 4. Wall Bracket

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

SHELVING

IMPORTANT: To achieve maximum performance,

interior louver openings and fan guard should

never be obstructed.

Refrigerator

The single door unit comes standard with black

vinyl coated adjustable full extension pullout

shelves.

Wine Reserve

The single door unit comes standard with four full

extension black vinyl coated wine racks capable

of storing 20 standard wine bottles. Shelves are

removable and/or adjustable. At the bottom, up to

2 1.5L bottles can be stored.

ADJUSTING FULL EXTENSION SHELVING

1. Pull the shelf out to its farthest position. Locate

the tabs in the middle of both extends (Figure

5). Press tabs and pull shelf out.

2. Reposition each bracket separately. Grasp the

middle of the bracket, pull the front end up and

out, then forward to remove (Figure 5).

3. Place bracket at the desired position. Push

the rear hook into the rear key slot. Set front of

bracket on the wall hook.

4. Repeat for other bracket(s).

5. Push extenders completely into the unit. Align

the shelf grooves with the extenders and slide

completely into the unit.

DOOR PANEL OPTIONS

Perlick units offer a variety of door panel design

alternatives; solid stainless steel, stainless steel

glass, black vinyl (glass or solid door) or laminate.

Solid stainless steel and stainless steel glass

doors are shipped from the factory with decorative

stainless steel panels and handles in place on the

appliance.If optional door lock is ordered, the unit

comes pre-assembled from the factory. Laminate

is also available in a variety of colors and patterns,

and is installed at the factory.

If ordered with the optional door lock, see Figure 6.

Door Lock Installation on page 9.

IMPORTANT: Glass doors may sweat in conditions

with relative humidity over 75%.

Press tabs and pull shelf out

Lift this end up

Figure 5. Adjusting the Shelving

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

9Form No.Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

Lock

Body

Lock

Bracket

Nut

Lock Strike

Lock Washer

Screw

Lock

Body

Lock

Bracket

Nut

Lock Strike

Lock Washer

Screw

1. Attach bracket to wood overlay

2. Insert lock body

3. Add and tighten nut

4. Add lock strike

5. Add lock washer and screw

6. Use key to turn the lock and verify that the lock and unlock positions of the strike are correct

(unlock should be up) (lock should be horizontal)

7. Adjust lock if necessary

8. Attached overlay with lock assembly to the door assembly

9. Attach lock bracket to unit

Figure 6. Door Lock Installation

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

OFF

COLD

Figure 7. Control Panel

OPERATION

General

The unit is equipped with a state-of-the-art

refrigeration system and is a frost-free model. The

evaporator coil automatically defrosts on demand

during off cycle.

Interior Light

The unit is equipped with an interior light that

illuminates when the door is opened. A manual

switch is located next to light for displaying the

product through a glass door. Always ensure

the manual switch is in the off position before

closing a solid door. If manual switch is left on for

an extended period of time, it may increase the

cabinet temperature, especially at the top, and

cause the refrigeration system to run longer.

Loading Product

IMPORTANT: When loading items into unit, do

not block interal louvers and fan guard openings

or performance will be decreased.

Temperature Control

The controller is located at the top rear panel of

the cabinet (Figure 7). Approximate temperature

operating ranges are:

■ Refrigerator: 33°F minimum, 39°F maximum

■ Wine Reserve: 40°F minimom, 65°F maximum

Adjusting the Temperature

■ Colder Temperature: Turn the adjusting screw

clockwise (to the right)

■ Warmer Temperatures: Turn the adjusting scrw

counterclockwise (to the left)

■ Temperature Control “OFF”: Turn the adjusting

screw completely counterclockwise to the

“OFF” position until a click is heard.

The condenser fan and motor turns off and on with

the compressor.

Inhaltsverzeichnis

Andere Perlick Kühlschrank Handbücher

Perlick

Perlick SDBR48 Bedienungsanleitung

Perlick

Perlick CR24 Bedienungsanleitung

Perlick

Perlick HA24RB4R Bedienungsanleitung

Perlick

Perlick SIGNATURE 15 Series Bedienungsanleitung

Perlick

Perlick 48" Signature Series Bedienungsanleitung

Perlick

Perlick HH24 Bedienungsanleitung

Perlick

Perlick CR30R Series Bedienungsanleitung

Perlick

Perlick 48" Signature Series Bedienungsanleitung

Perlick

Perlick CR30 Series Bedienungsanleitung

Perlick

Perlick 24"Signature Series Bedienungsanleitung

Perlick

Perlick HC24RS Bedienungsanleitung

Perlick

Perlick HPA24R Bedienungsanleitung

Perlick

Perlick CR24R12R Bedienungsanleitung

Perlick

Perlick HC Series Bedienungsanleitung

Perlick

Perlick BBSLP60 Bedienungsanleitung

Perlick

Perlick CR Series Bedienungsanleitung

Perlick

Perlick 24" C-Series Bedienungsanleitung

Perlick

Perlick ADA-Compliant Series Bedienungsanleitung

Perlick

Perlick HP24Z Bedienungsanleitung

Perlick

Perlick HC24 Bedienungsanleitung

Perlick

Perlick HC Series Bedienungsanleitung

Perlick

Perlick Signature HP15RS Bedienungsanleitung

Perlick

Perlick BBR96 Bedienungsanleitung

Perlick

Perlick CR24D Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung