Perlick R24N Bedienungsanleitung

INSTALLATION AND OPERATION INSTRUCTIONS

SINGLE DOOR REFRIGERATOR

Table of Contents

Cabinet Specifications ..........................................2

Installing

Uncrating and Inspection................................3

Plumbing.........................................................3

Electrical..........................................................3

Installing Shelves............................................3

Installing Casters or Legs ...............................3

Placing The Cabinet........................................3

Sealing the Floor.............................................4

Temperature Control.............................................4

Cleaning................................................................4

Cleaning Stainless Steel/Avoiding Corrosion .......4

Replacement Parts ............................................5/6

Wiring Diagram.....................................................7

Reversing the Doors.............................................8

8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069

Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com

IMPORTANT INFORMATION

This manual has been prepared to assist you in the

installation of your Single Door Refrigerator and to

acquaint you with its operation and maintenance.

We dedicate considerable time to ensure that our

products provide the highest level of customer

satisfaction. If, however service is required, call

Perlick at 1-800-777-7267 or your dealer who can

provide you with a list of qualified service agents. For

your own protection, never return merchandise for

credit without our approval.

We thank you for selecting a Perlick product

and assure you of our continuing interest in

your satisfaction.

IMPORTANT WARRANTY INFORMATION

A Warranty card is enclosed that must be completed

and mailed to the Perlick Corporation in order to

Perlick, the warranty period will begin from the date

the equipment is shipped from the factory.

MODEL NOS.

■■R24N

■■R24S

Form No. Z2288

Rev. 8.22.06

R24S R24N

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Installation and Operating Instructions

Single Door Refrigerator

Form No. Z2288

Rev. 8.22.06

Top View Front View End View

24”

[610]

8”[203]

8 7/16”[214]

34 1/2”

[887]

3 11/16”

[92]

30 9/16”

[776]

29 1/4”

[743]

NON-FINISHED

TOP

FINISHED

STAINLESS

TOP

5 9/16”

[141]

18 1/2”

[470]

24 1/4”

[615]

47 1/8”

[1197]

11 3/4”

[470]

25 3/4”

[654]

20”

[508]

180°

DOOR SWING

MODEL NOS. DOOR FINISH DOOR FINISH

R24NB Black R24SB Black

R24NS Stainless Steel R24SS Stainless Steel

R24NG Glass w/ Black Trim R24SG Glass w/ Black Trim

R24NT Glass w/ Stainless Trim R24ST Glass w/ Stainless Trim

EXTERIOR: Back, top and sides are Galvanized steel. Top and sides are stainless steel.

Back is galvanized steel.

Both models: Front is stainless steel. Doors: Either black vinyl CRS or stainless steel.

Bottom: galvanized steel with stainless grille.

INTERIOR Both models: Interior liner is stainless steel. Includes two adjustable vinyl coated shelves plus

a bottom shelf.

CABINET Length 24”(610)

DIMENSIONS Depth 24 1⁄4”(615)

(mm) Height 34 1⁄2”(887)

INTERIOR CU. FT. (m3) 4.9 (0.14)

SHELVING Bottom floor shelf and two additional shelves included

CASE CAPACITY* 4.6

CONDENSING UNIT H.P. 1/6 HP

RUNNING LOAD –AMPS 2.3

Ship Wt. Lbs. (kg.) 145 (54)

ELECTRICAL 115V, 60Hz., 1 phase . Furnished with 3-prong, 6 foot rubber plug in cord.

PLUMBING None required. Moisture drains to self evaporating condensate pan in machinery compartment.

INSULATION 2”foamed-in-place polyurethane insulation.

TEMPERATURE RANGE Adjustable from 32°F to +42°F (0°to 6°C).

REFRIGERATION R-134A capillary tube-type. with hermetic condensing unit. Front access for condenser and cleaning.

VENTILATION Front vented.

OPTIONAL •Set of 4 casters (33⁄4”high) P/N 65426.

ACCESSORIES & •Set of 4 adjustable legs (6”- 71⁄4”high) P/N 65423.

* Capacity calculations based on use of 12oz. export bottles on standard shelving.

NON-FINISHED TOP FINISHED TOP

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Preparing the Cabinet – Single Door Refrigerator

Uncrating and Inspection

Remove all crating material before operating.

Carefully inspect cabinet for hidden damage.

If damage is discovered, file your claim immediately

with the transport company. Perlick is not

responsible for damage in transit.

Plumbing

No plumbing connections are required. Condensate

from the cooling coil is automatically evaporated

through a condensate pan located in the

condensing unit section.

Electrical

The cabinet must be connected to a separately

fused power source (see Electrical Specification

Plate) and grounded in accordance with National

and Local Electrical Codes.

CAUTION: Do not attempt to operate the equipment

on any other power source than that listed on the

Electrical Specification Plate.

Placing the Cabinet

To assure maximum performance, fresh air must

be allowed to circulate through the machinery

compartment. Do not place anything in front of the

cabinet that would obstruct air flow at these grilles.

Do not place the unit in an unventilated small room.

Cabinet should be leveled front to back and side

to side.

Installing Casters or Legs (optional)

Attach casters or legs to the mounting bracket with

lockwashers and 1⁄4”–20 hex head nuts provided.

Attach bracket and leg/caster assembly to the side

of the cabinet base using the 1⁄4”–20 hex head self-

tapping machine screws provided.

Anti-tip (without Legs or casters)

To prevent the cabinet from tipping forward and to

provide a stable installation, the cabinet must be

secured in place with an anti-tip device.

A set of metal anti-tip brackets and installation

screws (#10-3⁄4” wood screws) are supplied. These

brackets should be attached to the floor, at the

back of the cabinet; each bracket located to catch

each rear leveling leg when the cabinet is pushed

backward into position.

THE ANTI-TIP BRACKETS MUST CATCH EACH

OF THE LEVELING LEGS TO HAVE A STABLE

AND SAFE INSTALLATION.

Some installation sites might need to be modified to

provide a secure surface for attaching the bracket.

Refer to the illustration below for anti-tip mounting

bracket locations.

Form No. Z2288

Rev. 8.22.06

1 1/2”20 7/8”

Cabinet must

have at least

5/16”clearance

from floor to

accomodate

brackets.

NOTE: Do not extend leveler leg

more than 3/4”out of base. Do not

shim or pad to obtain levelness.

Shown with leg

leveler engaged

in anti-tip bracket.

Surface

mounts

to floor.

Ø3/8”

7/16”

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Operation Instructions – Single Door Refrigerator

Sealing the Cabinet

For sanitation purposes, it may be necessary to

seal the base of the cabinet to the floor. This can be

accomplished by laying a bead of silicone sealant

between the base of the cabinet and the floor as

shown by the figure below.

When sealing the cabinet to the floor, make sure

that the louvered front grille plate can still be

removed for condenser maintenance and cleaning.

Cleaning the Cabinet:

■Use a mild detergent and water to clean the

inside and outside of the cabinet. Dry

thoroughly. Never use a scouring pad or

abrasive cleanser.

NOTE: An industrial strength, commercial

cleaner can be used to clean the outside of

painted cabinets

Cleaning the Condenser:

■Use a long handled, stiff brush to clean dirt

from the front surface of the condenser.

Keeping the condenser free from dust and

dirt will ensure efficient operation.

CAUTION: Do not bend the fins while

brushing the front of the condenser..

Temperature Control

An adjustable temperature control is located inside

the refrigerator on the evaporator fan panel

assembly. Approximate temperature operating

range: 32° F. minimum and 42° F.

maximum. Make adjustments as shown to attain

the desired

temperature.

■Colder Temperatures: Turn the adjusting

screw clockwise (to the right).

■Warmer Temperatures: Turn the adjusting

screw counterclockwise (to the left).

■Temperature Control “OFF”: Turn the

adjusting screw completely counterclock-

wise to the “O” position until a click is noted.

The condenser fan and the evaporator fan

motor turns off and on with the compressor.

Avoiding Stainless Steel Corrosion

Corrosion can be prevented by following product

cautions, cleaning instructions and avoiding use

of certain chemicals or objects which will cause

stainless steel corrosion.

STAINLESS STEEL ENEMY

■Steel wool or steel scouring pads

■Cherry/Orange/Olive juice

■Chlorine Bleach

■Sharp Objects

NORMAL

WARMER

COOLER

CONDENSING UNIT

Form No. Z2288

Rev. 8.22.06

BEAD SILICON

SEALER (RTV)

FLOOR

CABINET

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Replacement Parts – Single Door Refrigerator

Form No. Z2288

Rev. 8.22.06

■Service should be done by a qualified

refrigeration technician.

■Disconnect all power before servicing

the cabinet.

CAUTION

10 11

Replacement Parts – Single Door Refrigerator

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

MODEL NOS. ALL MODELS

Item Description Part Numbers

1 Compressor for R134A 63778

2 Condenser fan motor C15239A

3 Condenser fan motor bracket 60988-1

4 Condenser fan blade C22370

5 Condenser fan shroud 65206-2

6 Rear panel 65159-1

7 Front grille 65158-1

8 Condenser coil 65252

9 Condenser pan 65473

10 Evaporator fan guard 65254

11 Evaporator fan motor 65253

12 Evaporator assembly, complete H66136R

13 Top overlay 65429-1SS

14 Temperature control with dial plate 61271

15 Door assembly 66223

16 Magnetic door gasket 66237-1

17 Shelf 66236-1

18 Shelf, bottom 64809-1

19 Pilaster C19271

20 Shelf clip C15875

21 Evaporator grille 66139-2

22 Tip over bracket 63740

23 Door handle C31409-1

24 Leg kit set of 4 includes brackets 65423

25 Caster kit set of 4 including brackets (not shown) 65426

26 Complete hinge set-left (not shown) 66246L

27 Complete hinge set-right (not shown) 66246R

29 Power cord wiring harness (not shown) 65531

30 Evaporator assembly wiring harness (not shown) 65532

31 Evaporator fan motor wire harness (not shown) 65271

Form No. Z2288

Rev. 8.22.06

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Wiring Diagram – Single Door Refrigerator

Form No. Z2288

Rev. 8.22.06

JUNCTION

POINTS

JUNCTION

POINTS

JUNCTION

POINTS

BLUE

THERMOSTAT

BLACK

RED

BLUE

WHITE CONDENSER FAN

COMPRESSOR

END VIEW

RELAY

OVERLOAD

WHITE

GREEN

POWER CONNECTION

NEMA-15P CORD

WHITE

BLACK

GREEN

RED

WHITE

BLACK

EVAPORATOR FAN

Form No. Z2288

Rev. 8.22.06

8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069

Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Door Switching Instructions – Single Door Refrigerator

Tools Required

■Large Flathead Screwdriver.

■Regular Philips-head screwdriver.

■Small Philips-head screwdriver

Left Hinged Door

Units are available from

factory mounted left or right.

Workboard units are avail-

able with left mounting only.

All doors may be changed by

customer.

Operations to Perform NOTE: Changing

the door mount is

not advised if you

have a custom

wood overlay.

This may result in

having a handle

in an undesirable

location.

STEP 1:

Remove top hinge pin from assembly.

Carefully lift and tilt out door assembly

from the unit and set aside.

STEP 2:

Carefully remove hole plugs on right

side of unit. be careful not to

scratch unit. Top and bottom plugs

must be removed. Do not discard.

STEP 3:

Remove top and bottom hinge brackets from unit. Then

remove door closing insert and hinge pin from bottom

hinge bracket. See door bottom hinge assembly detail.

STEP 4:

Remove bottom hinge bracket to

allow you to remove the door closing

insert. Immediately replace hinge

bracket.

STEP 5:

Remove top hinge bracket to allow

assembly of door closing insert

removed in step 4. reassemble hinge

to door after installing the closing

insert.

Operation Notes

NOTE 1:

Lower left hinge

bracket rotates

180° and

becomes upper

right hinge

bracket.

NOTE 2 & 3:

Top left hinge bracket rotates 180°

and becomes bottom right hinge

bracket.

Bottom hinge pin and door closing

insert assemble to bottom right hinge

bracket.

NOTE 4: The hole plugs removed

earlier are to be inserted into the

vacant left door mounting holes. Do

not hit with hammer or damage may

occur. Use hammer handle or wood

block to push plugs into holes.

NOTE 5:

Door bottom on right mounted version was door top on

left mounted version. Before attempting to re-mount door

verify that: (1) The door handle will be on the outside of

door. (2) The door closing inserts are on the bottom. (3)

All screws are hand tightened, over tightening will dam-

age the unit.

STEP 1

STEP 5

STEP 4 STEP 3

STEP 2 NOTE 1

NOTE 2

NOTE 3

NOTE 5

NOTE 4

HINGE PIN

HOLE

PLUGS

HINGE

BRACKET

CLOSING

INSERT

BOTTOM

HINGE PIN

DOOR

HINGE

BRACKET

UNIT

HINGE

BRACKET

DOOR

CLOSING

INSERT

HINGE

BRACKET

CLOSING

INSERT HINGE

BRACKET

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Perlick Kühlschrank Handbücher

Perlick

Perlick HPA24R Bedienungsanleitung

Perlick

Perlick ARCTICPOUR RD060 Bedienungsanleitung

Perlick

Perlick 24" C-Series Bedienungsanleitung

Perlick

Perlick CR24R12R Bedienungsanleitung

Perlick

Perlick SHALLOW-DEPTH Series Bedienungsanleitung

Perlick

Perlick 48" Signature Series Bedienungsanleitung

Perlick

Perlick SDBR48 Bedienungsanleitung

Perlick

Perlick HB24 Series Bedienungsanleitung

Perlick

Perlick HC Series Bedienungsanleitung

Perlick

Perlick HP15 Bedienungsanleitung

Perlick

Perlick SIGNATURE 15 Series Bedienungsanleitung

Perlick

Perlick PR48 Bedienungsanleitung

Perlick

Perlick CS32SB Bedienungsanleitung

Perlick

Perlick R24N Bedienungsanleitung

Perlick

Perlick HP15 Bedienungsanleitung

Perlick

Perlick Residential Refrigeration Bedienungsanleitung

Perlick

Perlick BBSLP60 Bedienungsanleitung

Perlick

Perlick HA24RB4R Bedienungsanleitung

Perlick

Perlick HP24 Bedienungsanleitung

Perlick

Perlick HC24 Bedienungsanleitung

Perlick

Perlick HA24BB Bedienungsanleitung

Perlick

Perlick CR30R12L Bedienungsanleitung

Perlick

Perlick CR24D14R Bedienungsanleitung

Perlick

Perlick CR24 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung