Federal Communications Commission (FCC) Radio
Frequency Interference Statement
Warning
Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Information to the User
This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no guarantee that interfer-
ence of radio communications will not occur in a particular commercial installation. If this equipment does cause interference, which can be
determined by turning the equipment off and on , the user is encouraged to contact Pertech immediately.
Pertech is not responsible for any radio of television interference caused by unauthorized modication of this equipment, or the substitution of
attachment or connection cables and equipment other than those specied by Pertech. The correction of interferences caused by such unauthor-
ized modication, substitution or attachment will be the responsibility of the user.
Important Information to the User
In order to ensure compliance with the Product Safety, FCC and CE marking requirements. you must use the power supply, power cord, and
interface cable which were shipped with this product or which meet the following parameters:
Power Supply
Input power to this product must be provided by one of the following:
(1) A NRTL Certied power source with a Limited Power Source
(LPS) output for use in North America, input rated 100 - 240 Vac, 1.5 A, 50/60 Hz, Output rated 24Vdc, 2.5 A Maximum and 60W Maximum. or
(2) A power source with a Limited Power Source (LPS) output Certied by an agency recognized in the country of installation, input rated 100
- 240 Vac, 1.5 A, 50/60 Hz, Output rated 24Vdc, 2.5 A Maximum and 60W Maximum. Use of this product with a power supply other than the
Pertech power supply will require you to test this power supply and the Pertech printer for FCC and CE mark certication.
Interface Cable
A shielded (360 degree) interface cable must be used with this product. The shield must be connected to the frame or earth ground reference at
each end of the cable.
Use of a cable other than the described here will require that you test this cable with the Pertech printer and your system for FCC and CE mark
certication.
Power cord
For North America a NRTL Recognized detachable power cord must be used. For applications where the power supply module may be located
on the oor, a power cord with Type SJT marking must be used.
For applications outside of North America, Power cords which meet the country of installation’s certication and application requirements must
be used.
Use of a power cord other than described here may result in a violation of safety certications which are in force in the country of use.
Disclaimer
Information in this document is subject to change without notice. Consult your Pertech sales representative for information that is applicable and
current. Pertech reserves the right to improve products as new technology, components, software and rmware become available.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose with out the
express written permission of Pertech.
Industry Canada
This Class A digital apparatus complies with Industry Canada Standard ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 d’Industrie Canada.
Copyright
Copyright © 2005 by Pertech Resources Inc.
Riverton, Wyoming USA
All rights reserved. Printed in USA. Condential,
Unpublished. Property of Pertech® Inc..
Trademarks
Pertech® is a trademark of Pertech Resources, Inc. Other trademarks
and registered trademarks are the property of their respective holders.
220322A 5300 11/05 Rev. 04
Contact Information:
Documentation, Warranty
& Technical Support
Call: 800-800-6614
www.pertechresources.com
