Pfaff EcoDrive P40 ED Bedienungsanleitung

296-12-18 627/002

Betriebsanleitung engl. 06.09

INSTRUCTION MANUAL

Part 2

Control panel BDF S2

EcoDrive P40 ED

P70 ED

The reprinting, copying or translation of PFAFF Instruction Manuals, whether in whole or

in part, is only permitted with our previous authorization and with written reference to the

source.

PFAFF Industriesysteme

und Maschinen AG

Hans-Geiger-Str. 12 - IG Nord

D-67661 Kaiserslautern

Contents

Contents ............................................................................... Chapter - Page

1Operating elements of the S2 control panel ................................................................. 1

1.01 Screen displays ................................................................................................................. 1

1.02 Function keys .................................................................................................................... 1

1.03 Entering the start and end backtacks ................................................................................ 4

1.04 Setting the stitch count function for controlling the amount of bobbin thread .................. 5

1.05 Bobbin thread control on the sub-class -926/06 (optional) ................................................. 5

2Sewing ............................................................................................................................. 6

2.01 Manual sewing .................................................................................................................. 6

2.02 Programmed sewing ......................................................................................................... 7

2.03 An example of programmed sewing ................................................................................. 8

2.03.01 Programming by entering the number of stitches ............................................................. 8

2.03.02 Programming with the "teach function" ........................................................................... 11

2.04 Error messages ...............................................................................................................14

2.05 Explanation of the error signals ....................................................................................... 14

2.06 Parameter settings .......................................................................................................... 15

2.06.01 Selecting the user level ................................................................................................... 15

2.06.02 Selecting and altering parameters (only in the "manual sewing" mode) ........................... 16

3Adjustment .................................................................................................................... 17

3.01 Hardware-test ................................................................................................................. 17

3.01.01 Carrying out the hardware test ....................................................................................... 18

3.01.02 Test block 1 – inputs ....................................................................................................... 18

3.01.03 Test block 2 – outputs ..................................................................................................... 18

3.01.04 Test block 3 – speed control unit .................................................................................... 18

3.01.05 Test block 4 – actual value transmitters .......................................................................... 18

Contents

Contents ............................................................................... Chapter - Page

3.01.06 Test block 5 –light barrier ................................................................................................ 19

3.01.07 Test block 6 – thread monitor (only on subclass -926/06) ................................................ 19

3.02.08 Test block 7 – data transfer ............................................................................................. 19

3.03 Reset / Cold start ............................................................................................................ 20

3.04 Internet update of the machine software ........................................................................ 21

Controls

11 10

1 Operating elements of the S2 control panel

The control panel is used to create and alter seam programs, enter parameter values and

read error messages and service settings.

The control panel consists of display 1and the function keys described below. Display 1

consists of a two-row, alpha-numerical display with 16 symbols per row. The special

symbols 3and texts 4

show the respective status of the function keys and the operating

modes of the machine.

During the power-on phase the control panel automatically switches on all LCD segments

and the horn. The number of the version of the installed software then appears on the

display, until the higher-ranking control unit sends commands to the control panel.

1.01 Screen displays

●Activated functions are displayed with a triangular marking 2below or next to the

respective function key.

●In the sewing mode all relevant sewing data is displayed and these can be changed

directly, depending on the status of the machine, see also Chapter 2 Sewing.

●During the parameter input the selected parameter number with the corresponding value

is displayed, see Chapter 2.06 Parameter settings.

1.02 Function keys

The function keys described below are used basically to switch machine functions on and

off.

If a corresponding value has to be set for the activated function, this is carried out with the

corresponding +/- key. For example, by pressing and holding the +/- key 5, the numerical

value 6shown above the key is changed slowly to begin with. If the +/- key 5

is held down

longer, the numerical value 6is changed more quickly.

2 4

Controls

Start backtacks

●If this key is pressed, the backtacks at the beginning of the seam (start backtacks) are

switched on or off. The number of forward stitches (A) or reverse stitches (B) for the start

backtacks can be changed by pressing the +/- key underneath. To convert from double

backtack to single backtack set the number of stitches for the corresponding seam

section at zero.

End backtacks

●If this key is pressed, the backtacks at the end of the seam (end backtacks) are switched

on or off. The number of reverse stitches (C) or forward stitches (D) can be changed by

pressing the +/- key underneath. To convert from double backtack to single backtack set

the number of stitches for the corresponding seam section at zero.

Needle position

●If this key is pressed the "needle raised after sewing stop" function is switched on or off.

When the function is switched on, the needle positions at t.d.c. after sewing stops.

Foot position after stop

●If this key is pressed the "foot raised after sewing stop" function is switched on or off.

When the function is switched on, the presser foot is raised after sewing stops.

Foot position at end of seam/or after a seam segment (in programmed sewing)

●If this key is pressed the „Foot position raised at the end of a seam“ function is switched

on or off. When the function is switched on, the presser foot is raised at the end of a

seam.

Thread trimmer

●If this key is pressed the thread trimming function is switched on or off.

Speed (only in programmed sewing)

●If this key is pressed the corresponding function is switched on or off. In programmed

sewing the speed is not pedal-controlled. When the function is switched on, the speed

cannot be controlled by pedal. The machine only sews at the set maximum speed.

●When the function is switched off, the speed is controlled up to the maximum speed by

pedal

Reverse sewing (only in programmed sewing)

●If this key is pressed the corresponding function is switched on or off. When the function

is switched during programmed sewing, the corresponding seam section is sewn in

reverse.

Manual seam end (only in programmed sewing)

●If this key is pressed the corresponding function is switched on or off. When the function

is switched on, the move to the next seam section is not carried out by stitch counting or

sensor, but manually with the use of the pedal (position "-2").

Controls

Programmed stop

(only in programmed sewing)

●If this key is pressed the corresponding function is switched on or off. When the function

is switched on, in programmed sewing the machine stops automatically at the end of the

seam section.

Photocell

●In manual sewing the number of compensating stitches from the point where the

photocell is light to the end of the seam can be set under parameter 111, and in

programmed sewing directly.

Stitch counting (only in programmed sewing)

●If this key is pressed the corresponding function is switched on or off. When the function

is switched on, in programmed sewing the machines switches to the next sewing

section after the number of stitches entered have been sewn.

TE/Speed

●If this key is pressed once while the machine is in the sewing mode, the input menu for

the maximum speed is selected. If no input is made within 5 seconds, the sewing mode

is selected again.

●If this key is pressed twice (within 5 seconds) while the machine is in the sewing mode,

the machine switches to parameter input.

●If this key is pressed once while the machine is in the parameter input mode, the altered

values are stored and the sewing mode is selected.

Scrolling

●If this key is pressed, the machine scrolls between the sub-menus in the program.

●If this key is pressed the programmed sewing function is switched on or off. When the

function is switched on, the letters "PM" appear on the display of the control panel. The

parameters related to the program are shown in the alpha-numerical part of the display.

Press this key to sew a single stitch (only with control unit P70 ED)

Piece counter (only with control unit P70 ED)

When this key is pressed the first time, the piece counter is displayed for 3 sec.

If pressed again during the display period, the piece counter is reset.

The piece counter only counts when the "thread trimming" function is

activated.

No function

Controls

1.03 Entering the start and end backtacks

●Switch on the machine.

●By pressing the corresponding +/- key ("A")

select the desired value for the number of

forward stitches (A) of the start backtack.

●By pressing the corresponding +/- key ("B")

select the desired value for the number of

reverse stitches (B) of the start backtack.

●By pressing the corresponding +/- key ("C") select the desired value for the number of

reverse stitches (C) of the end backtack.

●By pressing the corresponding +/- key ("D") select the desired value for the number of

forward stitches (D) of the end backtack.

A B C D

3 3 3 3

Controls

No VAL

760 5

1.04

Setting the stitch count function for controlling the amount of bobbin thread

●Switch on the machine.

●Press the TE/Speed key twice to call up the parameter input function.

●Select the parameter "760" by pressing the corresponding +/- key.

●Press the corresponding +/- key to set the number of remaining stitches, which can still

be sewn after recognition by the bobbin thread control function.

The selected value is multiplied by 10* or 200** and the result is the number of stitches.

Example display 5 x 200** = 1000 stitches. The setting depends among other things on

the thread strength.

●If the TE/Speed key is pressed, the value is taken over and the machine changes into the

sewing mode.

The bobbin thread rest counter can only be used, if parameter "660" is set at

value "1" or "2".

*If for parameter 660 the value is "1", the multiplier is 10

** If for parameter 660 the value is "2", the multiplier is 200

VAL

No VAL

101 ON

1.05 Bobbin thread control on the sub-class -926/06 (optional)

Setting the bobbin thread control function, see the instruction manual for

-926/06.

Sewing

2 Sewing

In the sewing mode, all relevant settings for the sewing operation are shown on the display

and can be altered directly. Functions can be switched on or off by pressing a key.

In this mode a difference is made between manual sewing and programmed sewing. To

change from manual to programmed sewing, press the PM key. In programmed sewing the

text "PM" appears on the display.

2.01 Manual sewing

After switching on the machine and pressing the TE/Speed key, the max. speed can be set

with the corresponding +/- key.

Further functions in manual sewing, also see Chapter 1.02 Function keys:

Start backtacks on/off Foot position at end of seam on/off

End backtacks on/off Thread trimming on/off

Needle position raised on/off Photocell on/off

Presser foot raised on/off

4000

Speed

Andere Handbücher für EcoDrive P40 ED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pfaff Gleichstromantrieb Handbücher

Pfaff

Pfaff PicoDrive P40PD Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung