Phantos P24HEX Bedienungsanleitung

V1.0

20150826

Panel Wash HEX

Model Number: P24HEX

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

1/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

1. INTRODUCTION

Thank you for purchasing Panel Wash HEX. Please read this user manual

carefully and thoroughly before operation. Please keep this user guide for

future reference. This device has left our premises in absolutely perfect

condition. In order to maintain this condition and to ensure a safe operation,

it is absolutely necessary for the user to follow the safety instructions and

warning notes written in this manual. The manufacturer/distributors/dealers

will not accept liability for any resulting damages caused by the

non-observance of this manual or any unauthorized modification to the

device.

1.1 What is Included

a) 1X Panel Wash HEX with barn door

b) 1X user manual

Carefully unpack the carton, check the contents to ensure that all parts are

present and in good condition. Contact your supplier if any part is missing or

damaged.

1.3 Safety Instructions

▪ Avoid brute force when installing or operating the fixture.

▪ This device is for professional use only. It is not for household use.

▪ When choosing the installation spot, please make sure that the fixture is not

exposed to extreme heat or dust.

▪ Avoid using the unit in locations subject to possible impacts.

▪This unit is intended for indoor use only, use of this product outdoors voids

all warranties.

WARNING!!! To reduce risk of fire, electric shock, or

injury, follow these important safety instructions

2/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

▪ Always turn off, unplug power and allow fixture to cool before servicing.

▪ Ensure that fixture is properly grounded. Do not attempt to remove or

break off the ground prong from the electrical cord. This prong is used to

reduce the risk of electrical shock and fire in case of an internal short.

▪ Always make sure that you are connecting to the proper voltage and that

the line voltage you are connecting to is not higher than that stated on decal

or rear panel of the fixture.

▪ To prevent risk of fire or shock, do not expose fixture to rain or moisture.

▪ Make sure power cord is never crimped or damaged. Do not attempt to

operate this unit if the power cord has been frayed or broken.

▪ Do not remove the cover under any conditions, unless consent given by

distributor. There are no user serviceable parts inside.

▪ Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 15cm between this device and a wall.

▪DO NOT connect this product to a dimmer or rheostat.

▪ONLY connect this product to a grounded and protected circuit.

▪ONLY use the hanging/mounting bracket to carry this product.

▪USE a safety cable when mounting this product overhead.

▪DO NOT look at the light source when the product is on.

3/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

2. SET UP

2.1 Mounting

With adjustable mounting double brackets, this unit may be wall mounted, free

standing, or clamp mounted.

IMPORTANT!!! Safety cables must always be used. The safety cable must

be capable of holding 10 times the weight of the fixture.

2.2 Fixture Linking

To run your light shows of one or more fixtures using a DMX-512 controller or to

run synchronized shows on two or more fixtures in master/slave operating mode,

you need DMX cables to link the units from DMX IN to DMX OUT.

Only use standard 110-120 Ohm shielded cable. These are 2 core-screened

cables, with each core having at least a 0.5mm diameter. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact

with the XLR’s outer casing. Grounding the shield could cause a short circuit

and erratic behavior.

4/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

2.2.1 Line Termination

In DMX Mode, at the last fixture in the chain, the DMX output has to be

connected with a DMX terminator. This prevents electrical noise from

disturbing and corrupting the DMX control signals. The DMX terminator is

simply an XLR connector with a 120 (ohm) resistor connected across pins 2

and 3, which is then plugged into the output socket on the last projector in

the chain. The connections are illustrated below.

2.3 AC Power

This product has an auto-ranging power supply that can work with an input

voltage range of 100~240 VAC, 50/60 Hz.

Warning!!! All fixtures must be connected to circuits with a

suitable Earth Ground.

5/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

3 OPERATION INSTRUCTIONS

3.1 Menu Map

Display Function

A001-A512 DMX mode, 6CH

d001-d512 DMX mode, 10CH

CC00-CC99 Color macro 1

CP00-CP99 Color macro 2

dE00-dE99 Color macro 3

SS01-SS99 Macro Speed

bEbE Master mode

F --on-- Display on (--oFF, Display off)

R000-R255 Red Dimmer

G000-G255 Green Dimmer

B000-B255 Blue Dimmer

O000-O255 White Dimmer

Y000-Y255 Amber Dimmer

P000-P255 UV Dimmer

3.2 Auto Mode

In this mode, you can set the unit to run in static colors, strobe, or do color

changing without a DMX controller.

1. Press MENU button until display reads: “ CCxx ”, “CPxx” or “dExx”.

2. Press ENTER button and use UP/DOWN button to select number from 00-99

to adjust running speed from slow to fast.

3.3 DMX Mode

In DMX mode, you can control the fixture with a DMX controller.

1. Press MENU button until display reads: “ dxxx ” for DMX mode.

2. Then press ENTER button and use Up/Down button to set DMX address for the

fixture.

6/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

DMX Protocol:

6CH 10CH DMX Function

Ch1 0-255 Master dimmer

Ch1 Ch2 0-255 Red dimmer

Ch2 Ch3 0-255 Green dimmer

Ch3 Ch4 0-255 Blue dimmer

Ch4 Ch5 0-255 White dimmer

Ch5 CH6 0-255 Amber dimmer

Ch6 CH7 0-255 UV dimmer

Ch8 0-255 Master strobe

Ch9

0-49 No function

50-99 Macro 1

100-149 Macro 2

150-199 Macro 3

200-255 Sound activated

Ch10 0-255 Macro speed

3.4 Master/Slave Mode

In this mode, multiple units can be linked together as one system and run in sync.

Maximum 31pcs can be linked in a daisy chain as Master/Slave system.

1. Use DMX cable to link your lights together via DMX OUT to DMX IN connector.

2. One of the fixtures is set as Master (refer to 3.1 Menu Map on how to set a

fixture as Master) and this unit can then be set to work under any of the Auto,

Macro, Static Color, or Sound mode specified in 3.1 Menu Map. Others are to be

set as Slave mode (refer to 3.1 Menu Map on how to set a fixture to Slave mode,

if not mentioned then set to DMX address d001).

3. All slave units will follow master unit.

7/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

4.SERVICING

4.1 Fuse Replacement

1. Disconnect this product from power.

2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.

3. Remove blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power

4.2 Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical

lenses must be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth.

3. Always be sure to dry all parts completely before plugging the unit back in.

Cleaning frequency depends on the environment in which the fixture operates

(i.e. smoke, fog residue, dust, dew).

4.3 Trouble Shooting

1. Unit does not respond to DMX:

Check that the DMX cables are connected properly and are wired correctly (pin 3

is “hot”; on some other DMX devices pin 2 may be ‘hot’). It does matter which

way the inputs and outputs are connected.

Disconnect from mains before servicing.

8/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

5.TECHNICAL SPECIFICATIONS

WEIGHT&DIMENSIONS

Length 36cm including yoke

Depth 24cm including yoke

Height 15cm

Weight 5.3kg

POWER

AC Power AC110-240V 50/60Hz

Power Consumption 295W MAX.

Fuse

LIGHT SOURCE 24X12W RGBWAUV LEDs

Beam Angle 38 degree

PHOTOMETRICS DATA

N INTRODUCTIO

9/11 ©PHANTOS® Distributed in Australia by PHANTOS www.phantos.com.au

6 WARRANTY

Phantos Lighting hereby warrants, to the original purchaser, distributed products

to be free of manufacturing defects in material and workmanship for a prescribed

period from the date of purchase. This warranty shall be valid only if the product

is purchased in Australia through distributor/dealers. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence,

at the time service is sought.

For warranty service you must obtain a Return Authorization number (RA#) via

email before sending back the product. Send the product only to Phantos

Lighting. All shipping charges must be pre-paid. If the requested repairs or

service (including parts replacement) are within the terms of this warranty,

Phantos Lighting will pay return shipping charges only to a designated point

within Australia. No accessories should be shipped with the product. If any

accessories are shipped with the product, Phantos Lighting shall have no liability

whatsoever for loss of or damage to any such accessories, nor for the safe return

thereof.

This warranty is void if:

the serial number (if applied) has been altered or removed;

the product is modified in any manner which Phantos Lighting concludes,

after inspection, affects the reliability of the product;

the product has been repaired or serviced by anyone other than Phantos

Lighting unless prior written authorization was issued to purchaser by

Phantos Lighting;

the product is damaged because not properly maintained as set forth in

the instruction manual.

This is not a service contract, and this warranty does not include maintenance,

cleaning or periodic check-up. During the period specified above, Phantos

Lighting will replace defective parts at its expense with new or refurbished parts,

and will absorb all expenses for warranty service and repair labor by reason of

defects in material or workmanship. The sole responsibility of Phantos Lighting

under this warranty shall be limited to the repair of the product, or replacement

thereof, including parts, at the sole discretion of Phantos Lighting.

Phantos Lighting reserves the right to make changes in design and/or

improvements upon its products without any obligation to include these changes

in any products theretofore manufactured. No warranty, whether expressed or

implied, is given or made with respect to any accessory supplied with products

described above. Except to the extent prohibited by applicable law, all implied

warranties made by Phantos Lighting in connection with this product, including

warranties of merchantability or fitness, are limited in duration to the warranty

period set forth above. And no warranties, whether expressed or implied,

including warranties of merchantability or fitness, shall apply to this product after

said period has expired. The consumer’s sole remedy shall be such repair or

replacement as is expressly provided above; and under no circumstances shall

Phantos Lighting be liable for any loss or damage, direct or consequential, arising

out of the use of, or inability to use, this product.

45/7-9 Percy St, Auburn, NSW 2144, Australia

02 8034 8680

www.phantos.com.au

[email protected]

Stay Connected:

facebook.com/phantoslighting

twitter.com/phantoslighting

Inhaltsverzeichnis

Andere Phantos Beleuchtungsausrüstung Handbücher

Phantos

Phantos LED PAR CAN Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung