Phenix Technologies 400P Bedienungsanleitung

DCD 4120-10

USER’S MANUAL

DC DIELECTRIC TEST SET - 400P

MODEL NUMBER 4120-10

Version 3.2

Phenix Technologies Inc.

75 Speicher Drive

Accident, MD 21520

Rev 8/30/2018 ARFII

Rev 8/9/2019

DCD 4120-10

TABLE OF CONTENTS

DESCRIPTION SECTION NUMBER

INTRODUCTION

DANGER / GENERAL SAFETY PRECAUTIONS

TECHNICAL SPECIFICATIONS 1

CONTROLS AND INDICATORS 2

ELECTRICAL SET-UP 3

OPERATING INSTRUCTIONS 4

RETURN-GROUND-GUARD CONNECTIONS 5

CALIBRATION 6

TROUBLESHOOTING 7

STORAGE OF EQUIPMENT 8

CIRCUIT DIAGRAM SYMBOLS 9

RECOMMENDED SPARE PARTS AND PARTS LIST 10

PARTS ORDERING INFORMATION 11

RETURNED MATERIAL 12

ELECTRICAL DIAGRAMS 13

CUSTOMER COMMENTS / SUGGESTIONS 14

DCD 4120-10

INTRODUCTION

The DC Hipot line offered by Phenix Technologies is ruggedly built and suitable for field or lab use. Designed

to test electrical switchgear, cables, motors, generators and protective equipment, DC testing is popular

because the equipment is more compact and lighter in weight than comparable AC equipment.

Design and Safety Features

Output voltage continuously adjustable to 120kV DC.

“Zero Start” voltage interlock and external safety interlock.

Leakage current measurements available from .01 to 10,000 microamps DC.

Removable line cord.

Rotary switch selection simplifies operation.

Integrated cable storage bin in controls.

Built in discharge circuit rated at 12 kilojoules.

Light weight, portable, with controls enclosed in rugged, high-density polyethylene case.

Adjustable overcurrent trip point from 10%-110% of each range.

Large, easy to read LCD meters

Input Circuit Breaker / Power Switch

Thermal resettable overload protecting high voltage transformer primary circuits.

Very low ripple, <2% RMS ripple at full output. (>40 Meg Resistive)

For detailed specifications, see Section 1-1.

DCD 4120-10

DANGER / WARNINGS

Complete Grounding of this unit is necessary for the

safe operation of this equipment. Disconnect inputs

before ungrounding this equipment

DANGER

DCD 4120-10

GENERAL SAFETY PRECAUTIONS

This equipment can produce POTENTIALLY LETHAL VOLTAGES!

Improper operation or test practices may result in injury or death to the operator or

surrounding personnel.

The operation of High Voltage test equipment should only be performed by personnel

familiar with HIGH VOLTAGE testing and safety procedures. The operator of this

equipment must be aware of all hazards associated with High Voltage testing. The

operator is responsible for himself and others in close proximity of the testing area.

Some General Safety Practices for working with High Voltage Test Equipment have

been listed below for your reference.

•Become familiar with your instrument before performing an actual test

•Know your work area, check that all circuits are de-energized and locked out.

•Never work alone; always work with another qualified worker.

•Mark off entire work area with barriers and warning tape.

•Make all personnel aware of your testing activities.

•Be aware of dangerous conditions that may arise from energizing a test

specimen.

•Never modify test equipment, modifications to equipment could introduce an

unknown hazard or hinder a designed-in safety feature.

•DO NOT operate damaged equipment. Remove power, and do not use the

equipment until safe operation can be verified by service-trained personnel.

Phenix Technologies, Inc. assumes no liability for unsafe or improper use of test equipment.

DCD 4120-10

1-1

SECTION 1: TECHNICAL SPECIFICATIONS

Input

120 VAC 10 Amps or 220 VAC 5 Amps, 50/60 Hz, single phase (refer to Unit Data Tag)

Output Rating (maximum)

120 kilovolts DC, 10 milliamperes

Internal Discharge Capability: 12 kilojoules

Duty Cycle

Continuous –Capacitive Charging

Type of Cooling: Natural convection

Ripple: Less than 2 percent, at 120kV, (> 40 Meg Resistive)

Output

Negative output, positive ground standard. Positive output available by special order. Filtered voltage doubler

circuit, equivalent to full wave rectification.

Operating Ambient Temperature

0 to 40 degrees Celsius

Output Termination

High voltage cable, shield grounded

Metering

Output Voltmeter: 3 ½ DIGIT LCD, accuracy 0.5% of full scale.

Ranges: 0 to 19.99kV, 0-120.0kV

Output Currentmeter: 3 ½ DIGIT LCD, accuracy 0.5% of full scale.

Ranges of 0 to 19.99a, 199.9A, 1.999mA, 10.00mA

Size and Weight

Controls: 21.25" W x 16.75" D x 13.75" H; 25* lbs.

(540 mm W x 426 mm D x 350 mm H; 11.4* kg)

HV Unit: 17.25" W x 12" D x 22" H; 110 lbs.

(438 mm W x 305 mm D x 559 mm H; 49.9 kg)

Cables: 9.5 lbs. (4.3kg); *For 220 V units: add 10 lbs. (4.5 kg)

DCD 4120-10

2-1

SECTION 2: CONTROLS AND INDICATORS

Control Unit (Refer to Figure 2-1)

1. AC Power Input. Connect to a suitable grounded receptacle. See specifications tag on unit for voltage

and current requirements.

2. Voltmeter. Displays output voltage of test set.

3. Currentmeter. Displays current out of high voltage lead or into RTN terminal depending upon mode of

measurement.

4. Currentmeter Range Selector. Rotate to desired range.

5. J5. Interconnect cable between controls and HV unit connects here.

6. ANALOG CURRENT INDICATOR. Meter displays current from 0-100% of range to give visual

indications of capacitive charging conditions or to show changing current conditions that are not easily

determined from digital meters.

7. Output Voltage Control. Turn clockwise to increase output of test set. This control must be in the full

counterclockwise position (zero start) in order to turn High Voltage On. Under normal circumstances,

Voltage Control should always be returned to zero and voltage displayed on the voltmeter allowed to

decay to zero before pressing High Voltage Off.

8. High Voltage Off/Ready. Press to turn off high voltage output. Under normal circumstances the voltage

control should be returned to zero, and the high voltage allowed to decay near zero before switching

High Voltage OFF. CAUTION: Capacitive loads may retain voltage for a short time after high

voltage is turned off while the internal circuitry bleeds their charge to ground.

High Voltage Off/Ready lamp must be illuminated before High Voltage ON can be activated.

Conditions required for illumination are:

•External Interlock loop must be closed.

•Overcurrent Trip/Reset circuit must not be tripped. (Push Reset if circuit is tripped)

9. High Voltage On. Press to turn on high voltage.

Conditions required before high voltage will activate are:

•Voltage control at Zero Start

•External Interlock loop closed.

10. Current Trip Adjust. Dial adjusts from 1 to 11 corresponding to approximately 10% to 110% of selected

output current range. Current Trip/Reset lamp illuminates and high voltage turns off when output

current exceeds setting, causing circuit to trip. Circuit also acts as short circuit and overload protection

on high voltage output. To reactivate high voltage, Voltage Control must be returned to zero, and

Reset switch must be pressed to clear Current Trip circuit.

DCD 4120-10

2-2

CONTROLS AND INDICATORS

Control Unit (Cont’d)

11. Reset. Reset lamp illuminates to show that current trip circuit has tripped. High voltage circuits are

deactivated. Momentary Reset switch must be pressed to extinguish Reset lamp to allow high voltage

to be reapplied after returning Voltage Control to zero.

12. VOLTMETER RANGE SELECTOR. Rotate to appropriate setting for test voltage.

13. MAIN POWER INDICATOR. Lights to indicate that power is available for testing.

14. MAIN POWER CIRCUIT BREAKER. Press I to connect power, Press O to disconnect power.

15. F1. Control Power Fuse

16. THERMAL OVERLOAD. Circuit breaker protects primary of high voltage transformer. If circuit breaker

trips, turn High Voltage Off and return Voltage Control knob to zero before resetting.

17. External Interlock. If desired, remove jumper from connector and replace with cable connected to

contact(s) that must be maintained closed during testing. Some examples include footswitch, dead man

switch, gate interlock, panic button, etc. Only non-energized contact devices may be used. This is a

series 120 VAC circuit that must be maintained closed for high voltage to be activated or maintained.

DCD 4120-10

CONTROLS AND INDICATORS 2-3

FIGURE 2-1







































































PHENIX



TECHNOLOGIES



















PHENIX

























TECHNOLOGIES





DCD 4120-10

2-4

CONTROLS AND INDICATORS

CONTROLS (Cont’d)

High Voltage Unit (Refer to Figure 2-2)

1. J5. Interconnect cable from controls connects here.

2. Guard Terminal (GRD). Connect to Ground (GND) terminal (#3) for guard mode operation. Connect

currents that need to bypass the currentmeter to this point. Low potential side of specimen must be

isolated from ground to use this mode.

3. Ground Terminal (GND). Connects to Facility Ground. See (#2 and #4).

4. Return Terminal (RTN). Connect to Ground (GND) terminal (#3) for normal operation. Always connect

low side of test specimen to this point. This is the metered connection point for current.

Note: Further explanation of terminals occurs later under Return-Ground-Guard Section.

5. Grounding Clip-The grounding clip must always be connected from the Ground (GND) post to either the

Return (RTN) post or the Guard (GRD) post. Do not operate the unit with the clip removed or

disconnected.

6. High Voltage Bushing Well. High voltage output cable connects here. Opposite end attaches to the

high potential side of the test specimen.

Andere Handbücher für 400P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Phenix Technologies Prüfgeräte Handbücher

Phenix Technologies

Phenix Technologies PM10A Bedienungsanleitung

Phenix Technologies

Phenix Technologies BK130 Bedienungsanleitung

Phenix Technologies

Phenix Technologies HC-20C Bedienungsanleitung

Phenix Technologies

Phenix Technologies PM15-2 Benutzerhandbuch

Phenix Technologies

Phenix Technologies PM-20 Bedienungsanleitung

Phenix Technologies

Phenix Technologies LD60 Bedienungsanleitung

Phenix Technologies

Phenix Technologies PM15-4A Benutzerhandbuch

Phenix Technologies

Phenix Technologies HC2 Bedienungsanleitung

Phenix Technologies

Phenix Technologies PAD56 Benutzerhandbuch

Phenix Technologies

Phenix Technologies 6CP30/15-3 Bedienungsanleitung

Phenix Technologies

Phenix Technologies HC-5 Bedienungsanleitung

Phenix Technologies

Phenix Technologies BK Series Bedienungsanleitung

Phenix Technologies

Phenix Technologies 6CP200/100-10 Bedienungsanleitung

Phenix Technologies

Phenix Technologies 4160-5 Bedienungsanleitung

Phenix Technologies

Phenix Technologies HC-75C Bedienungsanleitung

Phenix Technologies

Phenix Technologies 6CP50/10-3 Bedienungsanleitung

Phenix Technologies

Phenix Technologies 660-10P Bedienungsanleitung

Phenix Technologies

Phenix Technologies 600P Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung