Philio PSE04-A Bedienungsanleitung

Multiple Sound Siren PSE04 A/B

Built-in high accuracy Temperature sensor

The PSE04 is a wireless siren, based on Z-Wave

technology. It is the

Z-Wave Pl s

prod ct, it s pport the sec rity, OTA... Those newest

feat res of the Z-Wave

technology. Z-Wave

is a wireless

comm nication protocol designed for home a tomation, specifically to

remotely control applications in residential and light commercial

environments. The technology ses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, s ch as lighting,

home access control, entertainment systems and ho sehold appliances.

This prod ct can be incl ded and operated in any Z-Wave

network

with other Z-Wave

certified devices from other man fact rers and/or

other applications. All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network.

The device adopt the Z-Wave

700 series chip, when yo r Z-Wave

network system is all made by Z-Wave

700 series devices. The

network system will have the advantages as below.

•Conc rrent m lti-channel s pport red ces external interference.

•Better RF range, improve abo t 10 meters in indoor.

•S pport 100 Kbps transmit speed, speed p comm nication.

Specification

Rating 6VDC (AA Battery *4), Max.300mA

RF distance Min. 40M indoor,

100M o tdoor line of sight,

RF Freq ency

868.40 MHz, 869.85 MHz(EU)

908.40 MHz, 916.00 MHz(US)

920.9MHz, 921.7MHz, 923.1MHz

(TW/KR/Thai/SG)

RF Maxim m Power +10dBm (Peak), -10dBm (Average)

Dimension 170mm(L) X 58mm (W) X 30mm(H)

Weight 205g

IP classification, Location IPx4; O tdoor se

Operation temperat re -20 to 54° C

H midity 85%RH max

FCC ID RHHPSE04

Max. so nd d ration time 110dB @30cm

M lti so nd

6 Different tunes, Fire

Alarm/Ambulance/Police/Alarm/Door

chime/beep

Temperat re detector range -20 to 54° C

Specifications are s bject to change and improvement witho t notice.

c



o

Siren Temperature

sensor

PSE04-A V V

PSE04- V

Troubleshooting

Symptom Ca se of Fail re Recommendation

The device can not

join to Z-Wave™

network

The device may in a Z-

Wave™ network.

Excl de the device

then incl de again.

For Instruction to http:// www.philio-tech.com

Overview

CAUTION

– replacement of a battery with an incorrect type that can defeat a

safeguard (for example, in the case of some lithium battery types);

– disposal of a battery into fire or a hot oven, or mechanically crushing

or cutting of a battery, that can result in an explosion;

– leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or the leakage of flammable

liquid or gas;

– a battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas

The marking information is located at the bottom of the apparatus.

Battery Installation

When the device report the low battery message. The ser sho ld

replace the battery to new one. The battery type is AA, 1.5V

Please loosen the screw on the back cover to release the front cover

Addin to Z-Wave

Network

There is one tamper key on the device. The tamper key can add,

remove, reset from Z-Wave

network.

In the first time, add the device into the Z-Wave

network. First,

make s re the primary controller is in the add mode. And then power

on the device. The device will a to start the SmartStart Incl sion mode.

Notice: Incl ding a node ID allocated by Z-Wave

Controller means

“Add” or “Inclusion”. Excl ding a node ID allocated by Z-Wave

Controller means “Remove” or “Exclusion”.

Function Description

Add

1. Have Z-Wave

Controller entered incl sion mode.

2. Pressing tamper key three times within 1.5 seconds

to enter the incl sion mode.

3. After add s ccessf l, the LED will light ON 1 second

Remove

1. Have Z-Wave

Controller entered excl sion mode.

2. Pressing tamper key three times within 1.5 seconds

to enter the excl sion mode.

3. Node ID has been excl ded.

Reset

Notice: Use this procedure only in the event

that the primary controller is lost or

otherwise inoperable.

1. Pressing tamper key fo r times within 1.5 seconds

and do not release the tamper key in the 4

pressed, and the LED will light ON.

2. After 3 seconds the LED will t rn OFF, after that

within 2 seconds, release the tamper key. If

s ccessf l, the LED will light ON one second.

Otherwise, the LED will flash once.

3. IDs are excl ded and all settings will reset to

factory defa lt.

SmartStart

1. Prod ct has a DSK string , yo can key in first five

digit to increment SmartStart process,or yo can

scan QR code.

Ex:mydsk

10209-46687-52248-13629-04783-07465-15776-56519

2. SmartStart enabled prod cts can be added into a

Z-Wave network by scanning the Z-Wave QR Code

present on the prod ct providing SmartStart

incl sion. No f rther action is req ired and the

SmartStart prod ct will be added a tomatically

within 10 min tes of min tes On in the network

vicinity.

*notice1:The QR code can be fo nd on the device

PSE04 or on the box.

Association

This machine provides one gro ps of nodes. Each

gro p can set 1 Nodes.

Gro p 1 is called Lifeline the device will report :

1.Notification report

2.Sensor m ltilevel report

3.Device Reset Locally Notification

4.Battery Report

5.Indicator Report

•Failed or s ccess in incl ding/excl ding the node ID can be

viewed from Z-Wave

Controller.

Notice 1: Always RESET a Z-Wave

device before trying to add it to a

Z-Wave

network.

LED Li ht Indication

The LED light indicates the different modes of the PSE04

State Type LED Indication

Witho t Node ID Under normal operation, when the PSE04 has not

been allocated a node ID, the LED light will flash on

and off alternately at 0.5 second intervals. By

pressing the On/Off b tton, LED light will stop

flashing temporarily.

Learning Slow flashes once when learning is s ccessf l.

Alarm Trigger All LED flashes ntil trigger off.

Z-Wave

Messa e Report

In defa lt the device will sing Notification Report to represent the

tamper trigger event.

* Tamper Report:

When the tamper key is pressed over 5 seconds. The device will into

the alarm state. In that state, if the tamper key be released, the device

will nsolicited to send the report to the nodes in the gro p 1.

Notification Report (V8)

Notification Type: Home Sec rity (0x07)

Event: Tampering. Prod ct covering removed (0x03)

* Siren State Report:

When the siren start playing or stop the alarm so nds, the device will

nsolicited to send the “Notification Report” to the nodes in the gro p

Notification Report (V8)

Notification Type: Siren (0x0E)

Event: Siren active (0x01) , Siren idle (0x00)

*Temperature Report:

When the temperat re differential over, the device will nsolicited to

send the “Sensor M ltilevel Report” to the nodes in the lifeline gro p.

Sensor Type: Temperat re (0x01)

*** Temperat re differential report ***

This f nction defa lt is disable, to enable this f nction by setting the

config ration NO.5 is greater than 0.

In the defa lt, is disable temperat re differential report.

If setting the config ration NO.5 to 1, when the temperat re is

changed to pl s or min s one degree Celsi s (1.8 degree Fahrenheit),

the device will report temperat re information to the nodes in the

lifeline gro p.

The device will meas re the temperat re in every 10 seconds.

Notice 1:

The PSE04 m st stay awake for at least 2 seconds after

comm nicating, so therefore the more comm nication, the power

consumption fast, please pay attention to se config ration NO.5.

Notice 2:

This prod ct cannot reflect o tdoor temperat re immediately

beca se of the temperat re sensor eq ipped inside rather than s rface.

*Play Sound:

Using the BASIC_SET or So nd_Switch_Tone_Play_Set to play the

siren, BASIC_SET

So nd_Switch_Tone_Play_Set

with Val e 0xFF, the

So nd ID will be the same as the val e which was set in Config ration

No.7

, 0x00 will stop to play.

Basic Set (V2) or Sound Switch Tone Pley Set (V1)

Val e So nd

0x00 Stop Play

0x01 Fire

0x02 Amb lance

0x03 Police

0x04 Alarm

0x05 Ding Dong

0x06 Beep

0xFF Same as config ration NO.7 setting,

or so nd switch config ration setting.

* Timin Report:

Beside the event triggered co ld report message, the device also

s pport the timing nsolicited report of the stat s.

●Battery level report: Every 6 ho rs report once in defa lt.

It co ld be changed by setting the config ration NO. 6.

●Low battery report: When the battery level is too low, every 30

min tes will report once.

●Temperat re report: Every 6 ho rs report once in defa lt.

It co ld be changed by setting the config ration NO. 4.

Notice: The config ration NO. 4 and 6 co ld be setting to

zero to disable the a to report. And the config ration NO. 1 co ld

change the tick interval, the defa lt val e is 30, if setting to 1, that

means the minim m a to report interval will be one min te. And please

notice if setting this val e to zero, that means disable all of the timing

report except the low battery detection.

Power Up Procedure

*Battery Power Check

When the device power p, the device will detect the power level of the

battery immediately. If the power level is too low, device will report low

battery even every 30 min tes. Please change another new battery.

*Wake up beam

If a Z-Wave controller or other node in the network needs to

comm nicate with a battery-powered device s ch as a door lock, the

controller sends a special beam signal. The p rpose of this beam is to

wake p the FLiRS device.

When the FLiRS device receives this beam, it immediately f lly wakes

p and then comm nicates with the controller or other Z-Wave device

tilizing standard Z-Wave protocol commands. If the device does not

hear a Beam it goes back to f ll sleep for another period ntil it

partially awakes again and listens for a Beam.

Over The Air (OTA) Firmware Update

The device is supported with Z-Wave™ firmware update via OTA.

1. Set the Z-Wave

Controller into the firmware update mode.

2. Choose the hex file to update the firmware.

3. Wait 10~15 minutes for completing the OTA process.

4. Result of OTA will show in Z-Wave™ Controller log.

During the OTA process, please DO NOT remove the power,

otherwise, the firmware will be broken, and the device will be

nonfunctional.

Z-Wave Confi uration Settin s

Notice 1:

All of the config ration, the data size is 1.

Notice 2:

The reserve bit or not s pported bit is allowed any val e, b t no

effect.

Notice 3:

The PSE04 m st stay awake for at least 2 seconds after

comm nicating, so therefore the more comm nication, the

power

consumption

fast, please pay attention to se

config ration

NO.1, NO.4,

NO.5, NO.6.

NO. Name Def. Valid Description

1A to Report

Tick Interval 0x1E 0~255 The interval time for a to report

each tick.

2So nd

D ration 0x06 0~255 Play so nd d ration, 1 tick is 30

seconds.

3 C stomer

F nction 0x00 All C stomer f nction switch, sing

bit control.



Bit0: Disable Trigger Alarm.

0:Enable , 1:Disable.



Bit1: Disable So nd. Only sing

optical alarm. 0:Enable ,

1:Disable.



Bit2: Temperat re Unit.

0:Fahrenheit , 1:Celsi s.



Bit3: Reserve.



Bit4: Reserve.



Bit5: Reserve.



Bit6: Reserve.



Bit7: Reserve.

A to Report

Temperat re

Time 0x0C 0~255 The interval time for a to report

the temperat re.

Temperat re

Differential

Report

0x00 0~255 The temperat re differential to

report.

6A to Report

Battery Time 0x0C 0~255 The interval time for a to report

the battery level.

7Play So nd

Control

0x43 All Control play so nd's level and

which so nd.



Bit0~1: Play so nd's level.

Level 1~3, 0: Level 3.



Bit2: Reserve.



Bit3: Reserve.



Bit4~7: Which so nd id will

play, when control form

controller.

So nd ID 1~6, 0: Disable.

Z-Wave Supported Command Class

Command Class Version Required Security Class

Z-Wave Pl s™ Info 2None

Sec rity 1None

Sec rity 2 1None

S pervision 1None

Transport Service 2None

Association 2Highest granted Sec rity Class

Association Gro p

Information

3Highest granted Sec rity Class

Device Reset Locally 1Highest granted Sec rity Class

Firmware Update Meta

Data

5Highest granted Sec rity Class

Indicator 3Highest granted Sec rity Class

Man fact rer Specific 2Highest granted Sec rity Class

M lti-Channel Association 3Highest granted Sec rity Class

Powerlevel 1Highest granted Sec rity Class

Version 3Highest granted Sec rity Class

Config ration 4Highest granted Sec rity Class

Sensor M ltilevel 11 Highest granted Sec rity Class

Basic 1 Highest granted Sec rity Class

Notification 8 Highest granted Sec rity Class

So nd Switch 1 Highest granted Sec rity Class

Battery 1 Highest granted Sec rity Class

Warnin

Caution,

avoid listenin at hi h volume levels for lon

periods

CAUTION

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used battery accordin to the instructions.

Choosin a Suitable Location

1. The s itable ambient temperat re for the mod le/device is

0°C~40°C.

2. Do NOT place the mod le/device direct nder s nlight, in a h mid

place or in any location where they may contact moist re, dirt, d st.

3. Do NOT place the mod le/device where exists comb stible

s bstances or any so rce of heat, fires, radiators, boiler etc.

Disposal

This marking indicates that this prod ct sho ld not

be disposed with other ho sehold wastes thro gho t

the EU. To prevent possible harm to the

environment or h man health from ncontrolled

waste disposal, recycle it responsibly to promote the

s stainable re se of material reso rces. To ret rn

yo r sed device, please se the ret rn and

collection systems or contact the retailer where the

prod ct was p rchased. They can take this prod ct

for environmentally safe recycling.

Philio Technology Corporation

8F., No.653-2, Zhongzheng Rd., Xinzh ang Dist., New Taipei City

24257, Taiwan(R.O.C)

w ww.philio-tech.com

FCC Interference Statement

This eq ipment has been tested and fo nd to comply with the limits

for a Class B digital device, p rs ant to Part 15 of the FCC R les.

These limits are designed to provide reasonable protection against

harmf l interference in a residential installation.

This eq ipment generates, ses, and can radiate radio freq ency en-

ergy and, if not installed and sed in accordance with the instr ctions,

may ca se harmf l interference to radio comm nications.

However, there is no g arantee that interference will not occ r in a

partic lar installation.

If this eq ipment does ca se harmf l interference to radio or televi-

sion reception, which can be determined by t rning the eq ipment off

and on, the ser is enco raged to try to correct the interference by one

of the following meas res:

•Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including inter-

ference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

警

警警

警語

語語

語:

「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變

更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，

應立即停用，並改善至無干擾時方得繼續使用。

前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合

法通信或工業、科學及醫療用電波輻射性電機設備之干擾。」

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philio Sicherheitssystem Handbücher

Philio

Philio PSE04 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung