Philips AurAir Bedienungsanleitung

Philips-AurAir Combination Installation Guide

Step 1: Connect the Philips Air Purifier to Wi-Fi

1. Download and install the Philips “Clean Home+”app

from the App Store or Google Play

2. Put the plug of the air purifier in the power socket and touch to turn on the air purifier

-> the Wi-Fi indicator blinks orange (ready to connect) when you install for the first time

-> if it does not blink orange press the two most left icons simultaneously for a few seconds

3. Make sure your smartphone is connected to the Wi-Fi network you want the purifier to connect to

4. Launch the “Clean Home+”app” and click “Connect a New Device” or press the “+”button on the

top of the screen. Follow the on-screen instructions to connect the air purifier to your Wi-Fi. Tip1:

when asked to create an account, you can choose the word ‘later’on top, to skip this for now. Tip2:

Give your purifier a logical name, for example the name of the room where it is installed.

5. When the Wi-Fi icon on your purifier is white and not blinking, your connection is successful!

Step 2: Connect the AurAir air quality meter to Wi-Fi

For Android Phones

1. Download and install the “AurAir Wifi” app from the Google Play store

2. Start the app, when asked for location, say yes

3. Make sure your smartphone is connected to the Wi-Fi network you want the meter to connect to

4. Check the Wifi name, enter the password, device count 1 of higher when installing more meters,

tag broadcast, press CONFIRM

5. Wait a minute, the red cross on the meter should be gone now. If the app gives an ip-address the

connection is made. You may also get the message connection failed. This step needs a reboot step

which could fail in some unexpected environments. It still may have worked. Check if the meter got

an IP address by pressing the settings button (the wheel) on the meter once. Reboot by putting the

meter out and in the power socket. Try again. If sometimes needs one or two tries to get it right.

For Apple Phones

1. Download and install the “Espressif Esptouch” app from the Apple Store

2. Start the app, when asked for location, say yes. Next step, select EspTouch.

Steps 3. to 5. Same as above

Step 3: Connect the AurAir and Philips to each other

1. On the AurAir meter, press the settings button (the small wheel) twice to see the QR code for the

AurAir web dashboard. Scan the QR code with your phone and click the link to see the dashboard.

2. On the AurAir dashboard you see the meter data and you change your meters settings. To connect

the AurAir and the Philips:

3. Choose the settings icon (the small white wheel) to get to the next screen

4. Choose the network icon to get to the AurAir-Philips connection screen

5. The first two sliders should be set on green, and press ‘send’ (= ‘verzenden’). The bottom slider will

say “searching”, and after a minute display the name of the purifier you want to connect to this

AurAir meter. Put that slider on green and press send. If you see more purifiers (if you are installing

multiple machine in a building) keep the other purifiers you see on red.

6. Test the connection by breathing on the meter until it turns yellow or red, the Philips cleaner must

now start automatically working in a higher mode.

Step 4: Troubleshooting the connection

1. Check if both products are still connected to your Wi-Fi (both should display the Wi-Fi icon in

white). When needed do a hard reset on each products by disconnecting it from the power source

for 30 seconds. Both products are designed to recover their connection to Wi-Fi and to each other.

2. Check, using the QR code, if the AurAir still sees the Philips. (The QR code appears after pressing

the settings button twice). On the portal 1st screen click the wheel on the left, 2nd screen click the

men bottom-left, 3rd screen has 3 sliders, make them all green, press send.

3. In case the connection cannot be established you can use the Philips in Automatic mode. The

Philips will still work. You can also operate the air purifier using the app on your phone.

Philips-AurAir Combination User Guide

Part 1: Operating the AurAir air quality meter

Part 2: Display of the AurAir air quality meter

Screen button

Press 1 time: Screen on black

Press 2 times: Scherm dimmed

Hold: Update firmware

Display button

Press 1 time: Show graph

Press 2 times: Show max/min measurements

Hold: Calibrate CO2 sensor

Settings button

Press 1 time: Show Cloud password

Press 2 times: Show QR code for web dashboard

Hold: Reset to factory settings

The Wifi symbol shows the meter is connect to your Wifi. A red cross in the

symbol indicates you are not (yet) connected to your Wifi.

CO2 is measured in ppm (parts per million).

<800 ppm is good (green), 800-1200ppm is fair (yellow), >1500ppm is bad (red).

Every minute all values are measured. The blue circle is drawn anew with every

measurement cycle.

Temperature is measured in degrees Celsius (numbers always displayed in white)

Relative humidity is displayed as a %. Between 40 and 60% is good (green), 60-

80% and 20-40% is medium (yellow) en outside 20-80% is unhealthy (red).

Airpressure measured in hPa. (numbers always white)

Philips-AurAir Combination User Guide

Operating the Philips Air Purifier

For a quick guide: please see instruction card included with your Purifier

For detailed instructions: please see user manual included with your Purifier

Notes on installing and using the Philips Air Purifier

The Philips Clean Home+ App supports the following conditions

•Wi-Fi with 2.4G Hz network

•WPA/WPA2 network

•Disable Mac address filter such as white list on router setting.

•Disable Connection limitation on router setting.

The Clean Home+ App does not support the following conditions:

•Enterprise network

•Wi-Fi network need webpage authentication, for instance, receiving verification code by

SMS.

•Wi-Fi network with WPA3 protocol

•Network only with 5G Hz.

•Customized router by Internet Service Provider.

The purifier must be within Wi-Fi’s signal scope while pairing and operation from Clean Home+ App.

FAQ about installing and using the Philips Air Purifier

Q: Is there any requirement of the smart device used for controlling the air purifiers.

Clean Home+ support can be installed on smartphone with IOS 13, Android 10 or above operation

systems in order to work correctly. Tablet control currently is not supported yet.

Q: How many air purifiers can be connected to one smartphone?

The Clean Home+ App supports at least 10 purifiers to be connected in one smartphone.

However, the operation may not be smooth, if you connect too many devices in one app.

Q: How many smartphones can be connected with one air purifier?

There could be at least 10 smartphones connected with same purifier. However, the operation may

not be so smooth, if purifier was connected with too many smartphones.

Q: Can I share the device with other people?

The purifier could also be simply added through local discovery with other Wi-Fi connected devices.

Once the air purifier is connected, it could also easily shared by scan QR code in app. You could also

choose to pair the purifier from beginning, please follow the instruction on User Manual.

Q: Does the Clean Home+ App support various permission management levels?

Currently, we do not support set various permission management levels in Clean Home+ App.

Inhaltsverzeichnis

Andere Philips Luftreiniger Handbücher

Philips

Philips AC4012 Bedienungsanleitung

Philips

Philips AC3821 Bedienungsanleitung

Philips

Philips AC4030/00 Bedienungsanleitung

Philips

Philips AC3829 Bedienungsanleitung

Philips

Philips AC1382 Bedienungsanleitung

Philips

Philips AC4012 Bedienungsanleitung

Philips

Philips AC4001 Bedienungsanleitung

Philips

Philips AC2882/10 Bedienungsanleitung

Philips

Philips AC1711 Bedienungsanleitung

Philips

Philips AC2729/10 Bedienungsanleitung

Philips

Philips AC4083 Bedienungsanleitung

Philips

Philips 4000i Series Bedienungsanleitung

Philips

Philips AC4054 Bedienungsanleitung

Philips

Philips AC4084 Bedienungsanleitung

Philips

Philips AC3252 Bedienungsanleitung

Philips

Philips AC4012 Bedienungsanleitung

Philips

Philips AC2887/31 Bedienungsanleitung

Philips

Philips AC3036/10 Bedienungsanleitung

Philips

Philips UVCA200 Bedienungsanleitung

Philips

Philips 3000i Series Bedienungsanleitung

Philips

Philips AC3033 Bedienungsanleitung

Philips

Philips AC4005 Bedienungsanleitung

Philips

Philips AC4081 Bedienungsanleitung

Philips

Philips AC4550 Bedienungsanleitung

Beliebte Luftreiniger Handbücher anderer Marken

IKEA

IKEA UPPÅTVIND Bedienungsanleitung

Nash

Nash AP-1 PureSmart Bedienungsanleitung

LG PH-U450 Series Bedienungsanleitung

DeLonghi

DeLonghi DDSX 220WFA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Bedienungsanleitung

Sharp

Sharp FU-40SE Bedienungsanleitung

Hitachi

Hitachi EP-A3000 Bedienungsanleitung

TruSens

TruSens Z-2000 Bedienungsanleitung

Motorola

Motorola MBP87SN Bedienungsanleitung

Beko

Beko ATP 7100I Bedienungsanleitung

Carrier

Carrier INFINITY 1620 Bedienungsanleitung

AtmosAir

AtmosAir P2002 Bedienungsanleitung

Winix

Winix NK300 Bedienungsanleitung

Friedrich

Friedrich C-90A Bedienungs- und Montageanleitung

Surgically Clean Air

Surgically Clean Air JADE2.0 Bedienungsanleitung

Base aire

Base aire 555 Pro Bedienungsanleitung

Champion

Champion CP25 Bedienungsanleitung

vollara

vollara Air & Surface Pro+ Bedienungsanleitung