Philips MANT901 Bedienungsanleitung

MANT901

EN User manual 3

SP Manual de utilizador 1 0

Manuel d'utilisateur 1 8

EN Contents

3 Safety Instructions

5 Included with Antenna

5 Mounting Antenna

6 Connecting to your TV

7 Warranty

8 Technical Support

Antenna grounding and safety warn-

ing

1. Outdoor antennas and lead-in conductors from antenna

to a building, should not cross over open conductors of

electric light or power circuits. They should be kept

away from all circuits to avoid the possibility of acciden -

tal contact.

2. Each conductor of a lead-in from an outdoor anten-

na should be connected with an antenna discharge unit.

Antenna discharge units (or Lightning Arrestor) should

be located outside the building or inside the building

between the point of entrance of the lead-in and the

TV, and as near as practical to the entrance of the con -

ductors to the building.

Important Safety Notes

If you do not feel comfortable or competent to install this

antenna we recommend that you seek the assistance of a

qualified professional antenna installer.

Read the instructions for this device thoroughly before

attempting installation.

The installation or dismantling of any antenna near power

lines is dangerous. Each year hundreds of people are killed

or injured while attempting to install or service antennas.

For your safety and proper antenna installation, read and

follow all safety precautions.

Choose an installation site for safety as well as perform -

ance.

All electric power lines, cable lines and telephone lines look

alike. To be safe, assume ANY overhead line can kill you.

Do not place an antenna where it could potentially fall on

to, or blow into a power line. If in doubt call your electric

provider. Let them review your site.

Outdoor antennas should be grounded with an approved

Safety Instructions

IMPORTANT

READ

BEFORE INSTAL-

LATION

NEC - National Electrical Cod e

*Antenna Discharge Unit is not

required if lead in conductors are

enclosed in a continuous metallic

shield that is permanently and

Warning Installation of this

product near power lines is

dangerous. For your safety,

keep ladder and antenna away

from power lines. Contact may

EN Safety Instructions

lighting arresting device. Local codes may apply. Use 8 AWG

or larger ground wire.

Height or other restrictions on antennas may apply to your

installation depending on your proximity to an airport, or

local ordinances.

Take the time to plan your installation procedure. Do all

assembly work on the antenna on the ground. Raise the

completed antenna after assembly.

Do NOT work on a wet, snowy or windy day or if a thun-

derstorm is approaching. Do NOT use a metal ladder.

If the antenna assembly starts to fall, get away from it and

let it fall. Remember that the antenna mast and cable are

all excellent conductors of electrical current.

Do NOT install the antenna by yourself. Be sure that there

are two other people available for help.

If any part of the antenna should come in contact with a

power line . . . DON'T TOUCH IT OR TRY TO REMOVE IT

YOURSELF. Call your local power company immediately.

They will remove it.

Should an electrical accident occur . . . DON'T TOUCH THE

PERSON IN CONTACT WITH THE POWER LINE, or you too

can become electrocuted. Instead, use a DRY board, stick,

or rope to push or pull the victim away from the power

lines and antenna. Once clear, check the victim. If he has

stopped breathing, immediately administer cardiopul -

monary resuscitation (CPR) and stay with him. Have some-

one else call for medical help.

Install wire antennas high enough that they will not be

"walked into" by people.

Do not install antenna wire(s) over or under utility lines.

IMPORTANT

READ

BEFORE INSTAL-

LATION

Parts included:

a. U H F B o o m - A . . . . . . . . . . . . 2

b. U H F B o o m - B . . . . . . . . . . . . 2

c. VHF Boom-A . . . . . . . . . . . . 1

d. V H F B o o m - B . . . . . . . . . . . . 2

e. Reflector Elements ....... 2

f. 46˝ Element . . . . . . . . . . . . 2

g. 50˝ Element . . . . . . . . . . . . 2

h. T u b i n g B r a c e . . . . . . . . . . . . 2

j. Phasing Wire . . . . . . . . . . . . 2

k. Reflector Brackets . . . . . . . . 2

l. Pivot Brackets . . . . . . . . . 4

n. Locking Brackets ......... 4

p. End Caps . . . . . . . . . . . . . . . 8

q. Screws (1-3/4˝) ......... 5

r. Screws (1-1/2˝) ........ 1 0

s. Screws (3/4˝) . . . . . . . . . . 2

t. Lock Washers/ Washers . 6, 4

u. W i n g - N u t s . . . . . . . . . . . . . 1 7

v. N u t s . . . . . . . . . . . . . . . . . . 6

Band Separator ............ 1

x. U-Bolt . . . . . . . . . . . . . . . . . 3

y. Cross Piece (for U-Bolt Assembly) 3

z. Antenna Saddle .......... 1

*Quantities listed include those which may already be attached to

antenna

NOTE: Cable, mast and mounting brackets are not included.

Included with

Assembly

Note: For final installation

and connection of your

antenna, additional hardware

may be required. Before

starting assembly, please

read through the instructions

carefully to determine your

EN Assembly

Assembly of UHF Portion

• Rotate reflector element rods into place. NOTE:

When rotating element rods, grasp close to pivot

and relieve spring pressure on pivot bracket

detents. Don’t apply excess pressure to reflector

element rods.

•Insert UHF Boom-A into UHF Boom-B and secure

using

1-1/2˝ screw and lock washer.

•Attach Reflector Arm Mounting Brackets to assem-

bled UHF Boom (previous step) using two 1-1/2˝

screws and wing-nuts. Ensure that rotation arcs in

Reflector Arm Mounting Brackets face toward UHF

Boom elements.

• Attach Corner Reflector Arms to Reflector Arm

Mounting Brackets by sliding Reflector Arms

between Mounting Brackets. Secure with 1-1/2˝

screw and wing-nuts. To fully secure Reflector

Arms, snap into locking tabs and tighten screws.

Assembly of VHF Portion

• Rotate reflector element rods on VHF Boom-A and

VHF Boom-B into place. NOTE: When rotating ele-

ment rods, grasp close to pivot and relieve spring

pressure on pivot bracket detents. Don’t apply

excess pressure to reflector element rods.

Assembly

• Attach one 46˝ Element to hole A in VHF Boom-B.

• Attach one 50˝ Element to VHF Boom-B.

Repeat each steps with second boom for VHF Boom-B.

•Insert VHF Boom-B into VHF Boom-A and secure

using 1-1/2˝ screw and lock washers. Repeat steps

for 2nd boom as well.

• Attach tubing brace to rear of VHF Boom with 1-

1/2˝ screws and wing-nuts.

• Slide UHF Boom through center slot of VHF Boom

support block until hole A of UHF Boom aligns with

hole B of VHF Boom. Secure with 1-1/2˝ screw

and wing-nut.

•Attach phasing wire and lead-in wire to UHF antenna

using 3/4˝ screws, washers, and wing-nuts.

•Insert end caps at ends of all booms.

Mast Assembly (Mast not included)

• Assemble U-bolts to cross pieces.

• Use saddle on center of boom.

EN Assembly

• Assemble U-bolt assemblies loosely to antenna.

• Insert mast through U-bolts.

• Tighten U-bolts securely. All U-bolts should be on

one side

of mast.

• Attach mast standoff to mast.

• Insert wire in standoff and tighten with pliers.

• Power lines should be as far away as possible.

•Assemble U-bolts in wall mounts with lock washers

and nuts.

• Secure mounts to wall with wood screws.

• Separate mounts by at least two feet.

• Insert mast with assembled antenna through both

U-bolts.

• Face antenna toward TV station.

• Tighten U-bolts securely.

• Wall mounts and chimney mounts are not included.

Lead-In Wire

•Attach lead-in wire to house with screw-type stand -

offs.

• Tighten standoffs with pliers after wire is installed.

• Avoid sharp bends in lead-in wire.

• Form drip loop where wire enters wall.

• Wall mounts not included.

• Mounts, mast and standoffs are not included.

Band Separator

• Attach band separator to appropriate terminals on

TV set.

• Attach antenna lead-in wire to band separator.

• An FM set or second TV set may be attached to sec-

ond output of band separator.

Wall

To Signal 

Splitter

Drip

Loop

Warranty

NOTE: Band separator is only required for older TV sets

with separate VHF/UHF inputs. For most newer sets,

simply connect cable from antenna to ‘F’ input.

Limited Lifetime Warranty

The manufacturer warrants that this product shall be

free from defects in material, workmanship and assem-

bly, under normal use, in accordance with the specifica -

tions and warnings, for as long as you own this product.

This warranty extends only to the original purchaser of

the product, and is not transferable. Defective products,

together with the dated proof of purchase, must be

returned to the place of purchase for repair or replace -

ment. THERE ARE NO OTHER EXPRESS WARRANTIES.

Incidental and consequential damages are disclaimed

where permitted by law. This warranty gives you specif-

ic legal rights, and you may also have other rights which

vary from state to state.

Technical Support

SP Contenido

1 1 Instrucciones de seguridad

1 3 Partes incluidas:

1 3 Para ensamblar

1 7 Garantía limitada por vida

1 7 Asistencia Técnica:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Antenne Handbücher

Philips

Philips SDV2780 - HDTV Antenna - Indoor Bedienungsanleitung

Philips

Philips SDV4401/27 Bedienungsanleitung

Philips

Philips SDV2710/27 Bedienungsanleitung

Philips

Philips SDV7700K/17 Bedienungsanleitung

Philips

Philips SDV2750/27 Bedienungsanleitung

Philips

Philips SDW1410GN Bedienungsanleitung

Philips

Philips SBCTT100/05 Bedienungsanleitung

Philips

Philips SDV9201/17 Bedienungsanleitung

Philips

Philips US2-MANT901 - Tv Antenna Uhf/vhf/fm/hdtv... Bedienungsanleitung

Philips

Philips SDV9011K Bedienungsanleitung

Philips

Philips SDV7114A Bedienungsanleitung

Philips

Philips SWS2083W Bedienungsanleitung

Philips

Philips SDW1420 Bedienungsanleitung

Philips

Philips SDV1121T/27 Bedienungsanleitung

Philips

Philips TT300 Bedienungsanleitung

Philips

Philips SDV8311B/27 Bedienungsanleitung

Philips

Philips SDV9201 Bedienungsanleitung

Philips

Philips MANT950 - TV Antenna - Indoor Bedienungsanleitung

Philips

Philips SDV3427W/27 Bedienungsanleitung

Philips

Philips SDW1850/17 Bedienungsanleitung

Philips

Philips SDV2720/27 Bedienungsanleitung

Philips

Philips SDV9201K Bedienungsanleitung

Philips

Philips SDV1227B/27 Bedienungsanleitung

Philips

Philips SDW1850/17 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch