Philips BDP2205 Bedienungsanleitung

Version 1.3

Blu-ray Player

Published by Arya & Lynn WK1417

3140 038 61483

BDP2205/F7/12/05

or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise

without the prior permission of WOOX Innovations. Philips and the Philips’Shield Emblem are

registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited

under license from Koninklijke Philips N.V.

Subject to modification

TABLE OF CONTENTS Page

Location of PC Boards & Versions Variation ........................1

Speciﬁcations .......................................................................2

Safety Instruction..................................................................3

Software Upgrade Instruction..................................................4

Troubleshooting....................................................................5

Disassembly Instructions .....................................................6

Set Block Diagram................................................................7

Set Wiring Diagram ..............................................................8

Circuit Diagram & PCBA Layout...........................................9

Revision List........................................................................11

Set Mechanical Exploded View ..........................................10

PCB Board Locations

VERSION VARIATIONS

Type / Versions

Service Policy /F7

Board in used

BDP2205

LOADER M

POWER BOARD

FRONT CONTROL BOARD

＊Tips：C -- Component Lever Repair

M -- Module Lever Repair

/1 2

/05

M M

MAIN BOARD

4 Performance Specifications

4.1 Audio Performance

4.1.1 Analogue Audio Outputs

NA.

4.1.2 Digital Audio Outputs

Standard Reference:

IEC60958

IEC61937

4.1.2.1 Coaxial Output

Description Specification Test Condition

Output Signal Amplitude 0.5Vpp ± 20% 75termination

Output Impedance 75± 20%

DC Output Voltage < 0.05V 75termination

Clock Accuracy < 100ppm (typical)

< 1000ppm (maximum)

Trise and Tfall < 0.4UI

Intrinsic Jitter < 0.05UI Weighted High Pass Filter used

(-3dB at 700Hz, -20dB at70Hz).

For specific TOSLINK requirements, refer to Jeita CP-1212 standard.

4.2 Standard DefinitionAnalogVideo Performance

4.2.1 CVBS

4.2.2 Component Video (Y/Pb/Pr)

4.3 High DefinitionAnalogVideo Performance

4.3.1 720p Component Video (Y/Pb/Pr)NA

4.3.2 1080i Component Video (Y/Pb/Pr)NA

4.4 FNAC Requirement

4.5 HDMI

Standard Reference:

High-Definition Multimedia Interface Specification version 1.3a

High-Definition Multimedia Interface Compliance Test Specification version 1.3c

HDMI 1.4 content type

2-1

4.6 USB

Standard Reference:

USB Specification Revision 2.0, dated 27th April 2000

USB-IF USB 2.0 Electrical Test Specification, Version 1.03, dated January 2005

USB-IF Embedded Host Compliance Plan, Revision 1.0, dated August 2006

Need to support USB HDD eg.2.5”. Refer to USB Device List from FRS.

USB HDD playback

FRONT

BDP22×× 1000mA continous

With specified load, need to provide minimum 4.75V at the end of a 0.75m USB reference cable.

4.7 Ethernet

Standard Reference: IEEE802.3-2005

Physical Layer: 10/100Base-T

Data rate: 10/100 Mbps

With Auto MDI/MDIX

4.8 WiFi

Standard Reference:

IEEE 802.11b Sept 1999

IEEE 802.11g June 2003

IEEE 802.11n Draft 2.0

2-2

5 Infra-Red Receiver

5.1 ReceiverRequirements

Parameters Requirement

Receiver Sensitivity

Receiver sensitivity

•E(0°) = 0.70 mW/m2on axis

•E(30°,h) = 1.12 mW/m2at= ±30° off

horizontal axis

•E(45°,h) = 2.19 mW/m2at= ±45° off

horizontal axis

•E(30°,v) = 1.12 mW/m2at= ±30° off

vertical axis

Max Distance

10m

7.92m

5.65m

7.92m

Short Operating Distance 0.1 m

Minimum Optical Viewing Angle Horizontal ( ) ± 60°

Vertical ( ) ± 30°

Electromagnetic Interference Field-strength: Eq100 V/m at nominal36kHz carrier

frequency.

2-3

6 Electrical Specifications

6.1 Mains Voltage / Mains Cord

Stroke

Version Voltage Frequency AC Cord Type

/12 220V-240V 50Hz VDE 2-pins round

/51 220V-240V 50Hz VDE 2-pins round

/55/78 100V - 240V 50Hz, 60Hz INMETRO 2-pins round mainscord(INMETRO-to-2-pins flat adaptor

to be included)

/93 100V - 240V 50Hz, 60Hz 2-pins flat

/96 100V - 240V 50Hz, 60Hz Taiwan Plug (CNS 690 approved)

/98 100V - 240V 50Hz, 60Hz VDE 2-pins round

Taiwan Plug (CNS 690 approved)

/F7 100-127V, 50Hz, 60Hz UL/ETL Plug, 2-pins flat

6.2 Mains Voltage Variation

Destination Main Voltage [V]/

Tolerance [%] Range Frequency

[Hz]

Europe 230 V

±15% 196V to 264V 47 Hz to 53 Hz

USA 120 V -20% / +10% 96V to 132 V 57 Hz to 63 Hz

Wide 120 V -20% / 230V +15% 96V to 264 V 47 Hz to 63 Hz

6.3 Mains consumption

Player must

•Register with and conform to Energy Star Commission;

•Conform to Directive 2005/32/EC (Commission Regulation EC No. 1275/2008).

In addition, the player must conform to the following requirement.

Function Requirement

1. Standby <0.5W

2. Operational 10W±10% (only playing disc and HDMI ouput)

11W±10% (with 1×500mA from USB and wifi

module)

6.4 Power On/Off Disturbances

>-52 dB suppression of the disturbance with regard to the rated output voltage.

The peak level has to be measured according to IEC 60651 weighted (A) curve.

2-4

6.5 Additional Requirements for India

6.5.1 VoltageRange Check

The set should work NORMALLY at mains voltage from 170V to 280V AC. (Incases of set with Audio

amplifiers, at lower mains voltages, audio rated poweroutput might be lower against the specified power

at nominal mains voltage, butremaining performance should be unaffected).

6.5.2 Soak Test

The set should be tested in ON condition with full loaded condition (MaximumAudio Power Output in

case of set with Audio Amplifiers) at mains voltage of 280VAC, for 4 hours.

6.5.3 310V AC Test

The set should be connected to 310V AC in Standby condition for 4 hours. Setshould work NORMALLY

after the test.

6.5.4 Immunity to Electrical Surge from External Devices (For India & ALL other Regions)

The product shall withstand Surge from external devices (e.g. TV) cinch connectors into ALL video outputs

without damaging any electrical component (e.g. MPEG IC)

All products shall have surge protection implemented for all Video Output terminals.

Test Condition:

1. Refer to ESD test setup and test condition to simulate the surge from external devices.

2. Contact Discharge to signal pin of cinch socket with below modified cinch connector jig to tap out the signal

line.

Requirement:

For India: Set must be able to withstand up to ±25kV contact discharge without any component damage.

For All Other Regions: Set must be able to withstand up to ±15kV contact discharge without any component

damage.

6.5.5 Immunity to DC Voltages from External Devices at CVBS Terminal (For India Only)

The CVBS video output must be DC isolated from external devices (e.g. TV and RF Modulators).

2-5

7 Mechanical Specifications

7.1 Mechanical Strength and Ease of Control

7.1.1 Mechanical Strength

Set exterior parts such as lens, buttonsetc, shall be able to withstand a force of 50N during 30 seconds from all

possible directions. The rigid test finger, according to IEC60065 clause: 9.1.8 should be used.

Set shall be proof against a pinch force of 150N, loaded by a bare hand. The product shall give a rigid

impression and shall not produce any annoying mechanical noise.

7.1.2 Rigidity of Top Surface

Set top must be able to withstand a force of 100N for duration of at least 30 seconds.

This force has to be applied by means of a flat plane of 4cm2(a plane with dimensions of 2cm x 2cm) at all

places at the top side.

7.1.3 Regularity of Operating Forces for Touch Control

Deviations in the regularity of the operating force of touch control shall not be perceptible by hand.

7.1.4 Moving of Set during Operation

Set shall not move (slide backwards) whilst operating the touch control on the set or inserting disc.

7.1.5 Maximum Temperatures

The maximum permissible temperature rises of the various external parts of a product are mentioned in the next

table.

The values of the temperature are based upon the maximum ambient temperature of 35°C.

The temperatures have to be measured after an operation time of 4 hours.

Maximum temperature rises with respect to the max ambient temperature.

External Product Parts Maximum Temperature Rise (°C)

Metallic Parts:

-front part of enclosure 10

-other parts of enclosure 25

Non-metallic Parts:

-enclosure 30

7.2 Detachable Mains Cord & Connector Sockets

7.2.1 Connector / Socket

a) Cinch sockets need to withstand a force of at least 100N in insertion and withdrawal directions and 50N

parallel to the set surface at 2cm distance.

b) If the connector socket is mounted directly on the PCB, the solder points have to be relieved

mechanically.

c) Connector / socket have to withstand the following minimal insertions and withdrawals,

•USBPort: 1500

•Other connectors: 500

2-6

7.2.2 NA

a) Detachable mains cord inlet has to withstand minimal 2500 insertions and withdrawals.

b) Mains cord operating force should be within the following limits:

•Withdrawal Force, P: 10N ≤ P ≤ 50N

•Insertion Force, F: F ≤ 50N

7.3 Visibility of User Interface Displays & Indicators

7.3.1 Viewing Angle

The visibility of display is possible under a viewing angle of 30˚from Top, Bottom, Left and Right.

Note: Viewing angle with regard to the perpendicular at the front of the apparatus.

7.3.2 Display illumination

The display / segment illumination should be uniform without undesirable light concentrations.

7.3.3 Brightness

As per reference. BDP2100.

7.3.4 Light Leakage

No light leakage is allowed (e.g. at connector sockets).

Above to be judge in dark condition to a bright condition of 600-800 lux

7.4 Screw Fixations

The screw fixations have to be designed in such a way, that after 10 times screwing and unscrewing, no

decrease of the quality of the fixation occurs.

The dimensions of thermoplastic bosses, intended for screw-fixations, have to be designed in such a way that

no deterioration of the fixation can take place, taken into account the environment conditions.

7.5 Support Foot

7.5.1 Type of material

Refer to MUS [3] for the type of material used.

1. Material for the support foot cannot shrunk in such a degree, e.g. after the Cyclic Humidity Test of 21

x 24 hours, that the set touches the furniture or other equipment during shifting. Minimum of 1mm

height should still be attained.

2. Material of the support foot cannot leave stains on furniture surfaces after climatic tests e.g. 70deg x

96hr.

3. The support foots shall prevent the set from moving over the underneath surface while normally

operating the set.

2-7

7.6 Touch Control Criteria

•NA

7.7 Bezel and Tray loader design

7.7.1 Strength

Permissible load on Bezel in any direction is ≥50N.The Tray & Bezel should not be broken or permanently deformed,

nor cause damage to other parts of set. The Bezel may dislodge above 30N without suffering any damage, and the

user must be able to easily put the Bezel back. Dislodge of the Bezel shall not cause damage to the set.

7.7.2 Actuating force needed for Tray

Force needed to actuate the tray should be ≤5N.

7.7.3 Tray Movement Cycle (Life Test)

24,000 open / close cycles

7.7.4 Tray Dimension

Refer to Appendix A.Disc should be fully out at tray open position.

7.8 Shock Sensitivity

Requirement:

No muting, plop sounds, picture freeze/jerk or audible/visible interference when impacting with force of -

In the ±X and ±Y directions: F ≥ 6g / 3ms, ΔV = 0.06ms

In the ± Z direction: F ≥ 4g / 3ms, ΔV = 0.04ms

where g = acceleration due to gravity

Refer to ODM Quality & Reliability handbook [6] for the details of the test discs and testing method.

7.9 Thermal Performance

Requirements:

1. Set should function normally

2. Temperature rise of PCB prints shall not exceed 85˚C

3. Temperature readings of all mechanical / electrical components and modules shall not exceed their

specification limits. The calculated junction temperature of semiconductors shall also not exceed spec

limits.

Refer to “ODM Quality & Reliability handbook [6] – Thermal Stability Test for player” for the details of the testing

method.

7.10 Dust Injection Test

Refer to “ODM Quality & Reliability handbook [6] – Dust Test”for details of the dust specifications and test

procedures.

2-8

Andere Handbücher für BDP2205

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Blu-ray-Player Handbücher

Philips

Philips BDP2700/12 Bedienungsanleitung

Philips

Philips BDP3000/05 Bedienungsanleitung

Philips

Philips BDP3380K/51 Bedienungsanleitung

Philips

Philips Qdeo BDP9700 Bedienungsanleitung

Philips

Philips BDP2600 Bedienungsanleitung

Philips

Philips BDP2500/98 Bedienungsanleitung

Philips

Philips BDP2600/94 Bedienungsanleitung

Philips

Philips BDP7500SL Bedienungsanleitung

Philips

Philips BDP3282/05 Bedienungsanleitung

Philips

Philips HTS3306/F7 Bedienungsanleitung

Philips

Philips BDP2100 Bedienungsanleitung

Philips

Philips BDP2930 /12 Bedienungsanleitung

Philips

Philips BDP2930/96 Bedienungsanleitung

Philips

Philips BDP5000/12 Bedienungsanleitung

Philips

Philips BDP1305 Series Bedienungsanleitung

Philips

Philips BDP2982/12 Bedienungsanleitung

Philips

Philips BDP2100 Bedienungsanleitung

Philips

Philips BDP5012 Bedienungsanleitung

Philips

Philips BDP-2850 Bedienungsanleitung

Philips

Philips BDP7500 MK II Bedienungsanleitung

Philips

Philips BDP5600/05 Bedienungsanleitung

Philips

Philips BDP3000/51 Bedienungsanleitung

Philips

Philips BDP2100/79 Bedienungsanleitung

Philips

Philips BDP2510B/05 Bedienungsanleitung

Beliebte Blu-ray-Player Handbücher anderer Marken

Samsung

Samsung BD-F5900 Bedienungsanleitung

Samsung

Samsung BD-P4600 Bedienungsanleitung

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Bedienungsanleitung

Pioneer

Pioneer BDP-140 Installations- und Betriebshandbuch

Samsung

Samsung BD-D8200A Bedienungsanleitung

LG HLX50W Bedienungsanleitung

Sony

Sony BDP-S300 - Blu-Ray Disc Player Bedienungsanleitung

Marantz

Marantz UD9004 Bedienungsanleitung

Panasonic

Panasonic DMR-HCT230 Bedienungsanleitung

LG BD611 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-PWT420 Bedienungsanleitung

LG BD611 Bedienungsanleitung

Marantz

Marantz BD7004 Kurzanleitung

Kogan

Kogan KABRP3DWFIA Bedienungsanleitung

Toshiba

Toshiba BDX2700 Bedienungsanleitung

Samsung

Samsung BD-E5400 Bedienungsanleitung

Samsung

Samsung BD-F5100 Bedienungsanleitung

LG UBK80.DUSALLK Bedienungsanleitung