Philips AZ1008/05 Bedienungsanleitung

AZ1008

CD Radio

Cassette Recorder

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 1

English

Mains plug

This apparatus is ﬁtted with an approved

moulded 13 Amp plug.To change a fuse in this

type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5 Amp,

A.S.T.A. or BSI approved type.

3Reﬁt the fuse cover.

If the ﬁtted plug is not suitable for your socket

outlets,it should be cut off and an appropriate

plug ﬁtted in its place. If the mains plug contains

a fuse, this should have a value of 5Amp.If a

plug without a fuse is used,the fuse at the

distribution board should not be greater than 5

Amp.

Note:The severed plug must be disposed to avoid

a possible shock hazard should it be inserted into

a 13Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code:blue = neutral (N), brown =

live (L).

• As these colours may not correspond with the

colour markings identifying the terminals in your

plug,proceed as follows:

• Connect the blue wire to the terminal

marked N or coloured black.

• Connect the brown wire to the terminal

marked L or coloured red.

• Do not connect either wire to the earth

terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover,make certain

that the cord grip is clamped over the sheath of

the lead - not simply over the two wires.

Recording and playback of material may require

consent.See Copyright Act 1956 andThe

Performer’s Protection Acts 1958 to 1972.

Important notes for users in the U.K. Norge

Typeskilt ﬁnnes på apparatens underside.

Observer: Nettbryteren er sekundert

innkoplet.Den innebygde netdelen er

derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk

støt;skal apparatet ikke utsettes for regn eller

fuktighet.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio AZ 1008 Philips

risponde alle prescrizioni dell’art. 2 comma 1 del

D. M. 28 Agosto 1995 n.548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips,Glaslaan 2,

5616 JB Eindhoven,The Netherlands

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 2

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CD TRACK

12 341 5

67 8 90! #@

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 3

English

CAUTION:Use of controls or adjustments or performance of procedures other than

herein may result in hazardous radiation exposure or other unsafe operation.

This product complies with the radio interference requirements of the European Union.

ATTENTION:L’utilisation des commandes ou réglages ou le non-respect des procédures

ci-incluses peuvent se traduire par une exposition dangereuse à l’irradiation.

Ce matériel satisfait aux impératifs de brouillage radio de la Communauté Européenne.

ATENCIÓN: El uso de mandos o ajustes o la ejecucción de métodos que no sean los

aquí descritos puede ocasionar peligro de exposición a radiación.

Este aparato satisface las normas relativas a la interferencia radioeléctrica de la

Comunidad Europea.

ACHTUNG:Der Gebrauch von Bedienelemente oder Einstellungen bzw.

Verfahrensausführungen die hier nicht ausdrücklich erwähnt worden sind,kann eine

gefährliche Strahlendosierung oder andere unsichere Operationen zur Folge haben.

Dieses Produkt entspricht den Funkentstörvorschriften der Europäischen Union.

LET OP:Het gebruik van de toetsen en regelingen of het toepassen van de

aanwijzingen anders dan hier beschreven,kan leiden tot blootstelling aan gevaarlijke

straling of tot onveilige werking.

Dit apparaat voldoet aan de radio-ontstoringseisen van de Europese Unie.

ATTENZIONE: L'uso dei comandi o regolazioni o prestazioni delle procedure oltre a

quelle descritte nel presente potrebbero causare esposizione a radiazioni pericolose

o altre operazioni rischiose.

Questo prodotto è conforme ai requisiti delle interferenze radio della Unione Europea.

AVISO:A utilização de comandos ou ajustes ou a execução de procedimentos de

forma diferente daquela aqui indicada poderá resultar numa exposição perigosa a

radiações ou noutra operação arriscada.

Este produto obedece aos requisitos referentes a interferência de rádio estabelecidos

pela União Europeia.

ADVARSEL:Anvendelse af andre betjeningsanordninger eller justeringer eller

udførelse af andre procedurer end de heri angivne,kan medføre udsættelse for farlig

stråling eller andre risici.

Dette apparat overholder EU's krav vedrørende radiostøj.

VARNING:Om du använder knapparna på annat än här angivet sätt eller utför

andra justeringar eller förfaranden än de här angivna kan du utsättas för skadlig

strålning eller andra risker.

Denna apparat uppfyller EU:s krav beträffande radiostörningar.

MUISTUTUS:Muiden kuin tässä kuvattujen säätimien tai säätöjen tai

toimenpiteiden käyttö voi aiheuttaa vaarallisen altistuksen säteilylle tai muun

turvallisuutta vaarantavan seurauksen.

Tämä tuote on Euroopan unionin radiohäiriöitä koskevien vaatimusten mukainen.

OO: O ,      

          ,    

         .

T            

.

Caution

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 4

SvenskaSuomi

English_________________6

Français_______________15

Español _______________26

Deutsch_______________37

Nederlands____________48

Italiano _______________59

Português_____________70

Dansk ________________81

Svenska_______________92

Suomi _______________103

 ____________114

Index

English Français Español Deutsch Nederlands Italiano Português Dansk

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 5

English

Top and front panels

1 LIFTTO OPEN – opens/ closes the CD

door

2 Source selector:CD,MW,FM,

TAPE/OFF

– selects CD source of sound,tuner

waveband or tape source of sound

– power on/ off switch

3 CASSETTE RECORDER:

PAUSE ;– pauses recording or playback

STOP•OPEN 9/ – stops the tape; opens

the cassette door

SEARCH 5or 6– fast rewinds / winds

the tape

PLAY 1– starts playback

RECORD 0– starts recording

4 CD display – shows the CD functions

5 TUNING

6 PLAY•PAUSE 2; – starts or pauses CD

playback

7STOP9– stops CD playback;erases a

CD programme

8 SEARCH ∞,§

CD:skips or searches a passage/track

backwards or forward

9 DBB (Dynamic Bass Boost) –

enhances bass response

10 REPEAT – repeats a track/CD/

programme

11 PROGRAM – programmes and reviews

programmed track numbers;

12 BATT LOW – indicator lights up if

battery power running low

13 VOLUME – adjusts volume level

Back Panel

14 Telescopic aerial – to improve FM

reception

15 Battery door – open to insert 6 x 1.5V

R14/UM2/ C-cell batteries

16 AC MAINS – inlet for mains lead

Power Supply

Whenever convenient,use the power

supply if you want to conserve battery life.

Make sure you remove the plug from the

set and wall socket before inserting

batteries.

For users in the U.K.:please follow the

instructions on page 2.

Batteries (not included)

1Open the battery compartment and insert

six batteries, type R-14,UM-2 or C-cells,

(preferably alkaline) with the correct

polarity as indicated by the "+" and "–"

symbols inside the compartment.

2Close the compartment door,and make

sure the batteries are ﬁrmly and correctly in

place.The set is now ready to operate.

➜If BATT LOW lights up,battery power

is running low.The BATT LOW indicator

eventually goes out if the batteries are

too weak.

Batteries contain chemical substances,

so they should be disposed of properly.

Controls Power Supply

6 x 1.5V R14/ UM2/ C CELL

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 6

English

Incorrect use of batteries can cause

electrolyte leakage and will corrode the

compartment or cause the batteries to

burst.Therefore:

• Do not mix battery types:e.g. alkaline with

carbon zinc. Only use batteries of the same

type for the set.

• When inserting new batteries,do not try to

mix old batteries with the new ones.

• Remove the batteries if the set is not to be

used for a long time.

UsingAC Mains

1 Check if the mains voltage, as shown on

the type plate located on the bottom

of the set,corresponds to your local

mains supply. If it does not,consult your

dealer or service centre.

2 Connect the mains lead to the AC MAINS

inlet and the wall socket.The mains supply is

now connected and ready for use.

3 To switch off completely,unplug the mains

lead from the wall socket.

• Unplug the mains lead from the wall socket

to protect your set during heavy

thunderstorms.

The type plate is located on the

bottom of the set.

Switching power on/off:

Save energy

Whether you are using mains or battery

supply, to avoid unnecessary energy

consumption always adjust the source

selector to TAPE/OFF and check if the

cassette keys are released.

General operation

1 To select your sound source adjust the

source selector to CD,MW,FM or

TAPE/OFF.

2 Adjust the sound with the VOLUME and

DBB (Dynamic Bass Boost) controls.

3To switch off the set, adjust the source

selector to TAPE/OFF position and check

the cassette keys are released.

Environmental information

All unnecessary packaging material has

been omitted.The packaging can be

easily separated into three materials:

cardboard,polystyrene and plastic.

Your set consists of materials which can

be recycled if disassembled by a

specialized company.Please observe the

local regulations regarding the disposal

of packing materials,exhausted

batteries and old equipment.

Power Supply

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 7

English

Radio reception

1 Adjust the source selector to MW or FM

to select your desired waveband.

2 Turn TUNING to tune to a radio station.

To improve reception

– For FM,pull out the telescopic aerial. Incline

and turn the aerial. Reduce its length if the

signal is too strong (very close to a

transmitter).

– For MW the set is provided with a built-in

aerial so the telescopic aerial is not needed.

Direct the aerial by turning the whole set.

3To switch off the radio,adjust the source

selector to TAPE/OFF position and check

the cassette keys are released.

CD Player

Display indication for CD functions:

– --:ﬂashes when CD source just selected

– In stop mode:total track number

– During CD playback:2and current

track number

REPEAT/ REPEATALL:when the

respective repeat mode is activated

– PROGRAM:when CD programme

active

– -- and PROGRAM:ﬂashes when

programme memory full

– Er:no disc/ error in CD operation or

with the CD/ CD-(R) is blank or the disc

is not ﬁnalised (seeTroubleshooting)

Playing a CD

1Adjust the source selector to CD.

2To open the CD door,lift the CD door at

the edge marked LIFTTO OPEN.

3Insert a CD or CD-(R) with the printed

side facing up and press the CD door gently

close.

4Press PLAY•PAUSE 2; on the set to

start playback.

5To pause playback press PLAY•PAUSE

2;.To resume,press PLAY•PAUSE 2;

again.

➜2ﬂashes during pause

6To stop CD play,press STOP 9.

7To switch off the set, adjust the source

selector to TAPE/OFF position and check

the cassette keys are released.

Note:CD play will also stop when:

– you open the CD compartment;

– you select MW,FM or TAPE sound

source;

– the CD has reached to the end.

Radio CD-Player

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 8

English

Selecting a different track

During playback you can use the

SEARCH buttons to select a particular

track.

• If you have selected a track number in the

stop or pause position,press

PLAY•PAUSE 2; to start playback.

• Press SEARCH §once brieﬂy for the

next track, or press repeatedly until the

desired track number appears in the display.

• Press SEARCH ∞once brieﬂy to return

to the beginning of a current track.

• Press SEARCH ∞more than once brieﬂy

for a previous track.

Finding a passage within a track

1During playback,press and hold down

SEARCH ∞or §.

• The CD is played at high speed and low

volume.

2When you recognize the passage you want

release the SEARCH button.

➜Normal playback resumes.

Note:When searching within a ﬁnal track and

you reach the end of the last track,the CD

goes to stop mode.

Repeat play modes

REPEAT can be selected or changed

during playback in the following sequence:

REPEAT – plays the current track

continuously

REPEATALL – plays the entire CD

continuously

1During playback,press REPEAT once or

more until the desired REPEAT mode is

shown.

• You can use SEARCH ∞or §to skip

tracks during the repeat modes.

• The REPEAT play options can be

combined and used with a programme: e.g.

REPEATALL PROGRAM– repeats the

entire CD programme.

2To return to normal playback press

REPEAT until the REPEAT modes are no

longer shown.

• You can also press STOP 9to quit the

play mode.

CD-Player

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 9

English

Programming track numbers

You may store up to 19 tracks in the

desired sequence.If you like, store any track

more than once.

1In the STOP mode,press PROGRAM to

activate programme mode.

➜00 and PROGRAM ﬂashes.

2Press SEARCH ∞or §for your desired

track.

➜Your selected track number and

PROGRAM ﬂashes.

3Press PROGRAM to store the track.

➜00 and PROGRAM ﬂashes,ready for your

next track selection.

4Repeat steps 2 to 3 to select and store all

desired tracks in this way.

➜-- and PROGRAM ﬂashes in the display

if you attempt to programme more than

19 tracks.

5To play your programme,press

PLAY•PAUSE 2;.

Reviewing your programme

• In the STOP mode,press PROGRAM

repeatedly to see your stored track

numbers.

Erasing a programme

You can erase the contents of the memory

by:

– opening the CD door;

– selecting MW,FM or TAPE sound

source;

– pressing STOP 9(twice during playback

or once in the stop position.)

➜Display:PROGRAM disappears.

CASSETTE RECORDER

Cassette playback

1Adjust the source selector to TAPE/OFF.

2Press STOP•OPEN 9/ to open the

cassette door and insert a recorded

cassette.

3Close the cassette door.

4Press PLAY 1to start playback.

5To pause playback press PAUSE ;.To

resume,press the key again.

6By pressing SEARCH 5or 6,fast

winding of the tape is possible in both

directions.To stop fast winding,press

STOP•OPEN 9/.

7To stop the tape, press STOP•OPEN 9/.

• The keys are automatically released at the

end of the tape, and the set is switched off,

except if PAUSE ;has been activated.

CD-Player Cassette Recorder

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

REPEAT

PROGRAM

TAP

OFF

•

IC BASS

DBB

TUNING

CDTRACK

XP AZ 1008/00-1 22-11-2000 21:02 Pagina 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips CD-Player Handbücher

Philips

Philips Magnavox AZ 7337 Bedienungsanleitung

Philips

Philips CD304 MK II Bedienungsanleitung

Philips

Philips AZ1515/17 Bedienungsanleitung

Philips

Philips AZ330T/85 Bedienungsanleitung

Philips

Philips AZ1145/00 Bedienungsanleitung

Philips

Philips AZ6822 - Portable Radio Cass Rec Bedienungsanleitung

Philips

Philips AZ1301 Bedienungsanleitung

Philips

Philips AZ6836 - Cd Portable Bedienungsanleitung

Philips

Philips AS450 Bedienungsanleitung

Philips

Philips AZ1028/61 Bedienungsanleitung

Philips

Philips AZ1307 - Portable Radio Cass Rec Bedienungsanleitung

Philips

Philips AZ3300-00C Bedienungsanleitung

Philips

Philips Soundmachine AZ382/12 Bedienungsanleitung

Philips

Philips CD723/20 Bedienungsanleitung

Philips

Philips Soundmachine AZ3067 Bedienungsanleitung

Philips

Philips FW548C/19 Bedienungsanleitung

Philips

Philips AX5013 Bedienungsanleitung

Philips

Philips AZ1575/17 Bedienungsanleitung

Philips

Philips EXP3361/07 Bedienungsanleitung

Philips

Philips AZ8245 Bedienungsanleitung

Philips

Philips AZ 7333 Bedienungsanleitung

Philips

Philips AZ1066 Bedienungsanleitung

Philips

Philips AS455 Bedienungsanleitung

Philips

Philips EXP2460/78 Bedienungsanleitung

Beliebte CD-Player Handbücher anderer Marken

RCA

RCA RP-7923 Bedienungsanleitung

Pioneer

Pioneer DEH-P3550MP XM Bedienungsanleitung

Lasonic

Lasonic MSU-2020 Bedienungsanleitung

THOMSON

THOMSON RCD150 Bedienungsanleitung

Denon

Denon DCD-1420 Bedienungsanleitung

Panasonic

Panasonic SJ-MR100 Bedienungsanleitung

Onkyo

Onkyo DX-7210 Bedienungsanleitung

Sony

Sony MZ-R3 Bedienungsanleitung

Denon

Denon DVM-4800 Bedienungsanleitung

JBL

JBL MR-32 Bedienungsanleitung

RCA

RCA RCD152 Bedienungsanleitung

Technics

Technics SL-PS770A Bedienungsanleitung

Clarion

Clarion compact disc Bedienungsanleitung

Sony

Sony MZ-M10 Bedienungsanleitung

Rotel

Rotel RCD 975 Bedienungsanleitung

Pioneer

Pioneer CLD-D790 Bedienungsanleitung

Optimus

Optimus CD-8250 Bedienungsanleitung

Audiovox

Audiovox CE101A - annexe 1 Bedienungsanleitung