Philips AZ1018/05 Bedienungsanleitung

AZ1018

CD Radio

Cassette Recorder

TAP

OFF

•

POWER

VOLUME

CDMODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 1

English

Mains plug

This apparatus is ﬁtted with an approved

moulded 13 Amp plug.To change a fuse in this

type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5 Amp,

A.S.T.A. or BSI approved type.

3Reﬁt the fuse cover.

If the ﬁtted plug is not suitable for your socket

outlets,it should be cut off and an appropriate

plug ﬁtted in its place.If the mains plug contains

a fuse,this should have a value of 5 Amp.If a

plug without a fuse is used,the fuse at the

distribution board should not be greater than 5

Amp.

Note:The severed plug must be disposed to avoid

a possible shock hazard should it be inserted into

a 13Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code:blue = neutral (N),brown =

live (L).

• As these colours may not correspond with the

colour markings identifying the terminals in your

plug,proceed as follows:

• Connect the blue wire to the terminal

marked N or coloured black.

• Connect the brown wire to the terminal

marked L or coloured red.

• Do not connect either wire to the earth

terminal in the plug,marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover,make certain

that the cord grip is clamped over the sheath of

the lead - not simply over the two wires.

Recording and playback of material may require

consent.See Copyright Act 1956 andThe

Performer’s ProtectionActs 1958 to 1972.

Important notes for users in the U.K. Norge

Typeskilt ﬁnnes på apparatens underside.

Observer:Nettbryteren er sekundert

innkoplet.Den innebygde netdelen er

derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk

støt;skal apparatet ikke utsettes for regn eller

fuktighet.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio AZ 1018 Philips

risponde alle prescrizioni dell’art.2 comma 1 del

D.M. 28 Agosto 1995 n.548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips,Glaslaan 2,

5616 JB Eindhoven,The Netherlands

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 2

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

45321

67 980!@#

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 3

English

CAUTION:Use of controls or adjustments or performance of procedures other than

herein may result in hazardous radiation exposure or other unsafe operation.

This product complies with the radio interference requirements of the European Union.

ATTENTION:L’utilisation des commandes ou réglages ou le non-respect des procédures

ci-incluses peuvent se traduire par une exposition dangereuse à l’irradiation.

Ce matériel satisfait aux impératifs de brouillage radio de la Communauté Européenne.

ATENCIÓN:El uso de mandos o ajustes o la ejecucción de métodos que no sean los

aquí descritos puede ocasionar peligro de exposición a radiación.

Este aparato satisface las normas relativas a la interferencia radioeléctrica de la

Comunidad Europea.

ACHTUNG:Der Gebrauch von Bedienelemente oder Einstellungen bzw.

Verfahrensausführungen die hier nicht ausdrücklich erwähnt worden sind,kann eine

gefährliche Strahlendosierung oder andere unsichere Operationen zur Folge haben.

Dieses Produkt entspricht den Funkentstörvorschriften der Europäischen Union.

LET OP:Het gebruik van de toetsen en regelingen of het toepassen van de

aanwijzingen anders dan hier beschreven,kan leiden tot blootstelling aan gevaarlijke

straling of tot onveilige werking.

Dit apparaat voldoet aan de radio-ontstoringseisen van de Europese Unie.

ATTENZIONE:L'uso dei comandi o regolazioni o prestazioni delle procedure oltre a

quelle descritte nel presente potrebbero causare esposizione a radiazioni pericolose

o altre operazioni rischiose.

Questo prodotto è conforme ai requisiti delle interferenze radio della Unione Europea.

AVISO:A utilização de comandos ou ajustes ou a execução de procedimentos de

forma diferente daquela aqui indicada poderá resultar numa exposição perigosa a

radiações ou noutra operação arriscada.

Este produto obedece aos requisitos referentes a interferência de rádio estabelecidos

pela União Europeia.

ADVARSEL:Anvendelse af andre betjeningsanordninger eller justeringer eller

udførelse af andre procedurer end de heri angivne,kan medføre udsættelse for farlig

stråling eller andre risici.

Dette apparat overholder EU's krav vedrørende radiostøj.

VARNING:Om du använder knapparna på annat än här angivet sätt eller utför

andra justeringar eller förfaranden än de här angivna kan du utsättas för skadlig

strålning eller andra risker.

Denna apparat uppfyller EU:s krav beträffande radiostörningar.

MUISTUTUS:Muiden kuin tässä kuvattujen säätimien tai säätöjen tai

toimenpiteiden käyttö voi aiheuttaa vaarallisen altistuksen säteilylle tai muun

turvallisuutta vaarantavan seurauksen.

Tämä tuote on Euroopan unionin radiohäiriöitä koskevien vaatimusten mukainen.

OO: O ,      

          ,    

         .

T            

.

Caution

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 4

SvenskaSuomi

English_________________6

Français_______________16

Español _______________26

Deutsch_______________36

Nederlands____________46

Italiano _______________56

Português_____________66

Dansk ________________76

Svenska_______________86

Suomi ________________96

 ____________106

Index

English Français Español Deutsch Nederlands Italiano Português Dansk

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 5

English

Top and front panels

1 Power slider:CD,RADIO,TAPE/OFF

– selects source of sound CD,RADIO,

TAPE/OFF,and the power on/ off switch

2 LIFTTO OPEN – opens/ closes the CD

door

3 Display – shows the status of the set

4 CASSETTE RECORDER:

PAUSE ;– pauses recording or playback

STOP•OPEN 9/ – stops the tape;opens

the cassette door

SEARCH 5or 6– fast rewinds / winds

the tape

PLAY 1– starts playback

RECORD 0– starts recording

5 BATT LOW – indicator lights up if

battery power is running low

6 PLAY•PAUSE 2; – starts or pauses CD

playback

7STOP9– stops CD playback;erases a

CD programme

8 SEARCH ∞,§

CD:skips or searches a passage/track

backwards or forward

RADIO – tunes to a radio station (up,down)

9 FM•MW – selects FM/ MW (AM)

waveband

10 PRESET 3,4– selects a preset station

(up,down)

11 CD MODE/ PROGRAM

CD – programmes and reviews

programmed track numbers;

– plays tracks CD/ programme in random

order;

– repeats a track/CD/ programme

RADIO – programmes radio preset stations

12 DBB (Dynamic Bass Boost) –

enhances bass response

13 VOLUME – adjusts volume level

Back Panel

14 Telescopic aerial – to improve FM

reception

15 Battery door – open to insert 6 x 1.5V

R14/UM2/ C-cell batteries

16 AC MAINS – inlet for mains lead

Power Supply

Whenever convenient,use the power

supply if you want to conserve battery life.

Make sure you remove the plug from the

set and wall socket before inserting

batteries.

For users in the U.K.:please follow the

instructions on page 2.

Batteries (not included)

1Open the battery compartment and insert

six batteries,type R-14,UM-2 or C-cells,

(preferably alkaline) with the correct

polarity as indicated by the "+" and "–"

symbols inside the compartment.

2Close the compartment door,and make

sure the batteries are ﬁrmly and correctly in

place.The set is now ready to operate.

➜If BATT LOW lights up,battery power

is running low.The BATT LOW

indicator eventually goes out if the

batteries are too weak.

Controls Power Supply

6 x 1.5V R14/ UM2/ C CELL

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 6

Batteries contain chemical substances,

so they should be disposed of properly.

Incorrect use of batteries can cause

electrolyte leakage and will corrode the

compartment or cause the batteries to

burst.Therefore:

• Do not mix battery types: e.g.alkaline with

carbon zinc.Only use batteries of the same

type for the set.

• When inserting new batteries,do not try to

mix old batteries with the new ones.

• Remove the batteries if the set is not to be

used for a long time.

UsingAC Power

1 Check if the mains voltage, as shown on

the type plate located on the bottom

of the set,corresponds to your local

mains supply.If it does not,consult your

dealer or service centre.

2 Connect the mains lead to the AC MAINS

inlet and the wall socket.The power supply

is now connected and ready for use.

3 To switch off completely,unplug the mains

lead from the wall socket.

• Unplug the mains lead from the wall socket

to protect your set during heavy

thunderstorms.

The type plate is located on the

bottom of the set.

Switching power on/off:

Save energy

Whether you are using mains or battery

supply,to avoid unnecessary energy

consumption always adjust the POWER

slider to TAPE/OFF and check if the

cassette keys are released.

General operation

1 To select your sound source adjust the

POWER slider to CD,RADIO or

TAPE/OFF.

2 Adjust the sound with the VOLUME and

DBB (Dynamic Bass Boost) controls.

3To switch off the set,adjust the POWER

slider to TAPE/OFF position and check

the cassette keys are released.

Note:When the set is switched off the tuner

presets will be retained in the set’s memory.

Power Supply

English

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 7

Radio reception

1 Adjust the POWER slider to RADIO.

➜Display:shows tu brieﬂy.The radio

frequency is then shown.

2 Press FM•MW once or more to select the

desired waveband.

➜Display:shows your waveband

3 Press and hold down SEARCH ∞or §

brieﬂy to tune to a radio station.Release

when the frequency in the display starts to

change.

➜The radio automatically tunes to a radio

station of sufﬁcient reception.Display

shows Srch during automatic tuning.

• To tune to a weak station,press SEARCH

∞or §brieﬂy and repeatedly until you

have found optimal reception.

To improve reception

– For FM,pull out the telescopic aerial.Incline

and turn the aerial.Reduce its length if the

signal is too strong (very close to a

transmitter).

– For MW (AM) the set is provided with a

built-in aerial so the telescopic aerial is not

needed.Direct the aerial by turning the whole

set.

4To switch off the radio,adjust the POWER

slider to TAPE/OFF position and check

the cassette keys are released.

Programming radio stations

You can store up to a total of 30 radio

stations in the memory.

1 Tune to your desired station (see Radio

Reception).

2 Press CD MODE/ PROGRAM to

activate programming.

➜Display:PROGRAM ﬂashes.

3 Press PRESET 3or 4once or more to

allocate a number from 1 to 30 to this

station.

4 Press CD MODE/ PROGRAM again to

conﬁrm the setting.

➜Display:PROGRAM disappears, the preset

number and the frequency of the preset

station are shown.

5 Repeat the above four steps to store other

stations.

• You can erase a preset station by storing

another frequency in its place.

Tuning to preset stations

Press PRESET 3or 4until the desired

preset station is shown.

Radio

English

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 8

CD Player

Display indication

–Cd OPEN:CD door open

–d1SC:when reading CDcontents

–In stop mode:total track number and

total playback time

–During CD playback:elapsed

playback time of current track and

current track number

–Pause:elapsed playback time freezes

and ﬂashes

–SHUFFLE/ REPEAT modes:when the

respective mode is activated

–PROGRAM:when CD programme active;

Progalso appears brieﬂy when you

store a track

–no SEL:programme activated but no

tracks selected

–FULL: programme memory full

–no Prog:programme cancelled

–Cd Err,no d1SC or nF d1SC:

error in CD operation /no disc/ or a

CD-R(W) is blank or the disc is not

ﬁnalized (seeTroubleshooting)

Playing a CD

This CD-player can play all kinds of Audio

Discs such as CD-Recordables and CD-

Rewritables.Do not try to play a CD-ROM,

CDi,VCD,DVD or computer CD.

1Adjust the POWER slider to CD.

➜Display:shows Cd brieﬂy.

2To open the CD door,lift the CD door at

the edge marked LIFTTO OPEN.

3Insert a CD or CD-R(W) with the printed

side facing up and press the CD door gently

close.

4Press PLAY•PAUSE 2; on the set to

start playback.

5To pause playback press PLAY•PAUSE

2;.To resume, press PLAY•PAUSE 2;

again.

➜The elapsed playback time freezes and

ﬂashes.

6To stop CD playback,press STOP 9.

7To switch off the set,adjust the POWER

slider to TAPE/OFF position and check

the cassette keys are released.

Note:CD play will also stop when:

– you open the CD compartment;

– you select RADIO or TAPE sound

source;

– the CD has reached to the end.

CD-Player

English

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 9

Selecting a different track

During playback you can use the

SEARCH buttons to select a particular

track.

• If you have selected a track number in the

stop or pause position,press

PLAY•PAUSE 2; to start playback.

• Press SEARCH §once brieﬂy for the

next track,or press repeatedly until the

desired track number appears in the display.

• Press SEARCH ∞once brieﬂy to return

to the beginning of a current track.

• Press SEARCH ∞more than once brieﬂy

for a previous track.

Finding a passage within a track

1During playback,press and hold down

SEARCH ∞or §.

• The CD is played at high speed and low

volume.

2When you recognize the passage you want

release the SEARCH button.

➜Normal playback resumes.

Note:During a CDprogramme or when

SHUFFLE/REPEAT is active, searching is only

possible within a track.

Different play modes

CD MODE/ PROGRAM allows you to

select various play modes.The modes can

be selected or changed during playback of

an entire CD/ CD programme in the

following sequence:

SHUFFLE – all tracks are played in

random order

SHUFFLE REPEATALL – repeats the

entire CD in random order

REPEAT – plays the current track

continuously

REPEATALL – plays the entire CD

continuously

1During playback,select your play mode by

pressing CD MODE/ PROGRAM once

or more until the desired play mode is

shown.

• You can use SEARCH ∞or §to skip

tracks during the SHUFFLE/ REPEAT modes.

• The SHUFFLE/ REPEAT play options can be

combined and used with a programme:e.g.

SHUFFLE/ REPEAT ALL repeats the entire

CD programme in random order.

2To return to normal playback press CD

MODE/ PROGRAM until the SHUFFLE/

REPEAT modes are no longer shown.

• You can also press STOP 9to quit the

play mode.

CD-Player

English

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

TAP

OFF

•

POWER

VOLUME

CD MODE

PROGRAM

PRESET

PLAY-

PAUSE

STOP

FM•MW

BATT

LOW

XP AZ 1018/00-1 13-12-2000 11:55 Pagina 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips CD-Player Handbücher

Philips

Philips Expanium EXP 103 Bedienungsanleitung

Philips

Philips AZ8049 - annexe 2 Bedienungsanleitung

Philips

Philips AX5018 Bedienungsanleitung

Philips

Philips AZ 7594 Bedienungsanleitung

Philips

Philips AZ7275 - Cd Personal Bedienungsanleitung

Philips

Philips AX3315 Bedienungsanleitung

Philips

Philips AZ 6836 Bedienungsanleitung

Philips

Philips AZ 6808 Bedienungsanleitung

Philips

Philips AZ3811/55 Bedienungsanleitung

Philips

Philips AZ 1004 Bedienungsanleitung

Philips

Philips AZ9555 Bedienungsanleitung

Philips

Philips Expanium AZ-2558 Bedienungsanleitung

Philips

Philips AZ1205 Bedienungsanleitung

Philips

Philips AZ1515/00C Bedienungsanleitung

Philips

Philips 3CDC-LC-MP3CD2002 Bedienungs- und Montageanleitung

Philips

Philips FW630/22 Bedienungsanleitung

Philips

Philips AZ 2048 Bedienungsanleitung

Philips

Philips EXP2540 Bedienungsanleitung

Philips

Philips AZ 7381 Bedienungsanleitung

Philips

Philips AZ6856 - Cd Portable Bedienungsanleitung

Philips

Philips AZ1840 Bedienungsanleitung

Philips

Philips Soundmachine AZ382/12 Bedienungsanleitung

Philips

Philips CD 711 Bedienungsanleitung

Philips

Philips AX2412/17 Bedienungsanleitung

Beliebte CD-Player Handbücher anderer Marken

RCA

RCA RP-7923 Bedienungsanleitung

Pioneer

Pioneer DEH-P3550MP XM Bedienungsanleitung

Lasonic

Lasonic MSU-2020 Bedienungsanleitung

THOMSON

THOMSON RCD150 Bedienungsanleitung

Denon

Denon DCD-1420 Bedienungsanleitung

Panasonic

Panasonic SJ-MR100 Bedienungsanleitung

Onkyo

Onkyo DX-7210 Bedienungsanleitung

Sony

Sony MZ-R3 Bedienungsanleitung

Denon

Denon DVM-4800 Bedienungsanleitung

JBL

JBL MR-32 Bedienungsanleitung

RCA

RCA RCD152 Bedienungsanleitung

Technics

Technics SL-PS770A Bedienungsanleitung

Clarion

Clarion compact disc Bedienungsanleitung

Sony

Sony MZ-M10 Bedienungsanleitung

Rotel

Rotel RCD 975 Bedienungsanleitung

Pioneer

Pioneer CLD-D790 Bedienungsanleitung

Optimus

Optimus CD-8250 Bedienungsanleitung

Audiovox

Audiovox CE101A - annexe 1 Bedienungsanleitung