Philips AZ1024/12 Bedienungsanleitung

CD Soundmachine

www.philips.com/welcome

User manual

AZ1024

AZ1024_A 2007.7.27 17:00 Page 1

8x R14 • UM-2 • C-CELLS

AZ1024_A 2007.7.27 17:00 Page 2

AZ1024_A 2007.7.27 17:00 Page 3

English Controls/Power Supply

Congratulations on your purchase and

welcome to Philips!

To fully benefit from the support that

Philips offers, register your product at

www.philips.com/welcome.

Supplied Accessories

– AC power cord

Top/front panels (see 1)

OPEN/CLOSE

–opens/ closes the CD

door.

§ ∞ SKIP

–

selects the next/previous track

– searches forwards/backwards (press and

hold the button) within the current track

STOP –

stops CD playback;

–

erases a CD program;

2 ; PLAY/PAUSE - starts or pauses CD

playback

REPEAT

–

repeats a track/

CD program/entire CD.

6PROG. – programs tracks

DBB

–

turns the bass enhancement on/off

8Telescopic antenna - improves FM

reception

LED Display

–

shows the CD functions

Back/bottom panels (see 1)

VOL

–

adjusts volume level

Source selector:CD,TUNER, OFF

–

selects CD or radio source of sound

–

power off switch

@Battery door - open to insert 8 x 1.5V

R-14/ UM-2/ C-cells

#TUNING

– tunes to radio stations

BAND –

selects MW, FM or FM ST. wave-

band

%AC MAINS~- inlet for power cord.

^p– 3.5 mm stereo headphone socket

Helpful hints: The speakers will be muted

when headphones are connected to the set.

CAUTION

Use of controls or adjustments or

performance of procedures other

than herein may result in unsafe

operation.

This set complies with the radio

interference requirements of the

European Union.

Power Supply

Whenever convenient, use the power supply

cord if you want to conserve battery life.

Make sure you remove the plug from the set

and wall outlet before inserting batteries.

Batteries (not included)

1 Open the battery door and insert 8batteries,

type R-14,UM-2 or C-cells, (preferably

alkaline) with the correct polarity as indicated

by the "+" and "–" symbols inside the com-

partment. (see 1)

2 Replace the battery door, making sure the bat-

teries are firmly and correctly in place.The set is

now ready to operate.

• Incorrect use of batteries can cause

electrolyte leakage and will corrode the

compartment or cause the batteries to burst:

• Do not mix battery types: e.g. alkaline with car-

bon zinc. Only use batteries of the same type

for the set.

• When inserting new batteries, do not try to mix

old batteries with the new ones.

• Remove the batteries if the set is not to be used

for a long time.

Batteries contain chemical substances, so

they should be disposed of properly.

AZ1024_A 2007.7.27 17:00 Page 4

Power Supply General Operation/Tuner

Using AC power

WARNING:Always check you have

completely switched off the set, before

you change or disconnect power supply.

1 Check if the power voltage, as shown on

the type plate located on the

bottom of the set, corresponds to your

local power supply. If it does not, consult your

dealer or service center.

2 Connect the power cord to the AC

MAINS~ inlet and the wall socket.The set is

now connected and ready for use.

3 To switch the set off completely, withdraw the

power cord from the wall socket.

4Install the unit near the AC outlet and where

the AC power plug can be easily reached.

•Disconnect the power cord from the wall

socket to protect your set during heavy thun-

derstorms. Children could seriously injure

themselves as the free end of the cable may

still be live if only the connector is removed

from the MAINS socket at the back of the

unit.

The type plate is located on the

bottom of the set.

Helpful hints:

–To avoid unnecessary energy consumption,

always adjust the

Source selector

OFF

after using the set.

General operation

Switching on and off and selecting the

function

1 To select your sound source, adjust the

Source selector to: CD or

TUNER

2To switch off the set, adjust the Source

selector to

OFF

position.

Adjusting volume and sound

Adjust the sound with the VOLUME and

DBB controls.

Radio reception

1 Adjust the Source selector to

TUNER

2 Adjust BAND to select your desired

waveband, MW,FM or FM ST.

➜FM ST. LED will light up when radio is

receiving stereo broadcast.

3Tur n TUNING to tune to a station.

Helpful hints:

To improve radio reception

• For FM,extend, incline and turn the telescop-

ic antenna for best reception. Reduce its

length if the signal is too strong.

•To tune to a weak FM station, adjust BAND

to FM (mono).

• For MW,the set uses a built-in antenna.

Direct this antenna for best reception by

turning the whole set.

AZ1024_A 2007.7.27 17:00 Page 5

Playing a CD

•This CD player plays Audio Discs including

CD-Recordables (CD-R) and CD-Rewritables

(CD-RW).

•MP3, CD-ROM, CD-I, CDV,VCD, DVD or

computer CDs are not possible for playback.

IMPORTANT!

CDs encoded with copyright protection

technologies by some record companies may

be unplayable by this product.

1Adjust the Source selector to CD.

2Open the CD door, and insert a CD with

the printed side facing up, then press the CD

door gently to close.

➜Display shows --,and later the total

number of tracks. (see 2)

3Press

to start playback.

➜PLAY/PAUSE LED lights up.

4To pause playback, press

➜PLAY/PAUSE LED flashes.

5To resume, press

again.

6To stop CD playback, press

Helpful hints:

CD play will also stop when:

–you open the CD door;

–you select

TUNER

OFF

sound source;

–the CD has reached the end.

Selecting a different track

•Press

∞/ §SKIP

once or repeatedly until

the desired track number appears in the dis-

play.

•In the pause/stop position, press 2; to start

playback.

Finding a passage within a

track

1During playback, press and hold ∞or § .

➜ The CD is played at high speed and with

reduced volume.

2When you recognize the passage you want,

release ∞or §to resume normal playback.

Helpful hints:

– When your searching reaches the end of the

last track, the CD goes to stop mode.

Programming track num-

bers

You may store up to 20 tracks in the desired

sequence. If you like, store any track more

than once.

1In the stop position, press PROG. to

activate programming.

➜“0”flashes. (see 3)

➜PROG LED also flashes.

2Press

∞

to select your desired track

number.

3Press PROG. to store the desired track

number.

➜“0”flashes for you to program the next

track.

4Repeat steps 2 to 3to select and store all

desired tracks in this way.

➜If you attempt to store more than 20

tracks, no track can be selected and the

display shows flashing ----.

5To play your program, press

➜PROG LED flashes during playback.

Helpful hints :

– When playback of your program comes

to the stop position, your set will return

to normal playback.To re-enter program

mode, press PROG in the stop position.

CD Player

AZ1024_A 2007.7.27 17:00 Page 6

Erasing a program

You can erase the contents of the memory

by:

– pressing

– selecting

TUNER

OFF

;

– opening the CD door.

REPEAT play mode

You can play the current track or the whole

disc repeatedly, and combine REPEAT modes

with PROG (PROGRAM).

1To select play mode, press REPEAT once or

more.

➜REPEAT LED flashes – plays the cur-

rent track continously.

➜REPEAT LED lights up – repeats the

entire CD/program.

2Press 2; to start playback if in the stop/pause

position.

3To return to normal playback, press

REPEAT

repeatedly until the REPEAT LED lights off.

– You can also press 9to cancel your play

mode.

CD Player

AZ1024_A 2007.7.27 17:00 Page 7

CD player and CD handling

•If the CD player cannot read CDs correctly,

use a cleaning CD to clean the lens before

taking the set to repair.

•The lens of the CD player should never be

touched!

•Sudden changes in the surrounding

temperature can cause condensation on the

lens of your CD player. Playing a CD is then

not possible. Do not attempt to clean the

lens but leave the set in a warm environment

until the moisture evaporates.

•Always close the CD-tape door to avoid dust

on the lens.

•To clean the CD, wipe in a straight line from

the center towards the edge using a soft,

lint-free cloth. Do not use cleaning agents as

they may damage the disc.

•Never write on a CD or attach any stickers

to it.

Safety information

•Place the set on a flat, hard and stable surface

so that the system does not tilt.

•Where the MAINS plug or an appliance cou-

pler is used as the disconnect device, the dis-

connet device shall remain readily operable.

•Do not expose the set, batteries, CDs to

humidity, rain, sand or excessive heat caused

by heating equipment or direct sunlight.

•The apparatus shall not be exposed to drip-

ping or splashing.

•Adequate ventilation with a minimum gap of

15cm (6 inches) between the ventilation

holes and surrounding surfaces is necessary

to prevent heat build-up.

•Do not cover the ventilation openings with

items such as newspapers, table-cloths, cur-

tains, etc.

•No objects filled with liquids, such as vases,

shall be placed on the apparatus.

•No naked flame sources, such as lighted can-

dles, should be placed on the apparatus.

•The mechanical parts of the set contain

self-lubricating bearings and must not be oiled

or lubricated.

•To clean the set, use a dry cloth. Do not use

any cleaning agents containing alcohol,

ammonia, benzene or abrasives as these may

harm the housing.

Maintenance & safety (see 4)

AZ1024_A 2007.7.27 17:00 Page 8

Problem

–Possible cause

•Remedy

No sound /power

–Volume not adjusted

•Adjust the VOL

–Power cord not securely connected

•Connect the AC power cord properly

–Batteries dead/ incorrectly inserted

•Insert (fresh) batteries correctly

–Headphones connected to the set

•

Disconnect headphones.

–CD contains non-audio files

•Press

∞,§

once or more to skip to a CD audio

track, instead of the data file.

Display does not function properly / No

reaction to operation of any of the

controls

–Electrostatic discharge

•Switch off and unplug the set. Reconnect after a

few seconds.

Severe radio hum or noise

–Electrical interference: set too close to TV, VCR or com-

puter.

•Increase the distance.

Poor radio reception

–Weak radio signal

•FM: Adjust the FM telescopic antenna.

-- indication

–No CD inserted

•

Insert a CD

–CD badly scratched or dirty

•

Replace/ clean CD, see Maintenance

–Laser lens steamed up

•Wait until lens has cleared

–CD-R/CD-RW is blank or not finalized

•

Use a finalized CD-R/CD-RW or suitable CD

Audio disc only.

Note:

Make sure the CD is not encoded with

do not conform to the Compact Disc stan-

dard.

The CD skips tracks

–CD damaged or dirty

•Replace or clean CD

–Program is active

•Quit program mode

Note: A CD badly scratch or dirty may result in

improper operation.

Troubleshooting

If a fault occurs, first check the points listed below before taking the set for repair.

If you are unable to remedy a problem by following these hints, consult your dealer or service centre.

WARNING: Do not open the set as there is a risk of electric shock. Under no

circumstances should you try to repair the set yourself, as this will

invalidate the guarantee.

AZ1024_A 2007.7.27 17:00 Page 9

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of

plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 3 Amp,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a

value of 3 Amp.If a plug without a fuse is used, the fuse at the distribution board

should not be greater than 3 Amp.

Note:The severed plug must be disposed of to avoid a possible shock hazard should it

be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N),

brown = live (L). As these colours may not correspond with the colour markings iden-

tifying the terminals in your plug, proceed as follows:

•Connect the blue wire to the terminal marked N or coloured black.

•Connect the brown wire to the terminal marked L or coloured red.

•Do not connect either wire to the earth terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the two wires.

Recording and playback of material may require consent. See Copyright Act 1956 and

The Performer’s Protection Acts 1958 to 1972.

AZ1024_A 2007.7.27 17:00 Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips CD-Player Handbücher

Philips

Philips CD840 - annexe 1 Bedienungsanleitung

Philips

Philips AZ8075 - Portable Radio Cass Rec Bedienungsanleitung

Philips

Philips AZ1412 Bedienungsanleitung

Philips

Philips AZT9240 Bedienungsanleitung

Philips

Philips AZ9015 Bedienungsanleitung

Philips

Philips AZ9003/19 Bedienungsanleitung

Philips

Philips Jogproof AX3312 Bedienungsanleitung

Philips

Philips AZ5140 Bedienungsanleitung

Philips

Philips AZ9235 Bedienungsanleitung

Philips

Philips AZ7275 - Cd Personal Bedienungsanleitung

Philips

Philips AZ2025 - annexe 1 Bedienungsanleitung

Philips

Philips AZ7372/00S Bedienungsanleitung

Philips

Philips AZ1834/55 Bedienungsanleitung

Philips

Philips AZ1200 Bedienungsanleitung

Philips

Philips CD304 MK II Bedienungsanleitung

Philips

Philips EXP2461 Expanium Bedienungsanleitung

Philips

Philips AZ1515/05 Bedienungsanleitung

Philips

Philips AZ1120/11H Bedienungsanleitung

Philips

Philips AZ1837/55 Bedienungsanleitung

Philips

Philips AZ1226 Betriebsanleitung

Philips

Philips EasyStar FC8802 Bedienungsanleitung

Philips

Philips AZ9355 Bedienungsanleitung

Philips

Philips Soundmachine AZ3831 Bedienungsanleitung

Philips

Philips AZ7275 - Cd Personal Bedienungsanleitung

Beliebte CD-Player Handbücher anderer Marken

RCA

RCA RP-7923 Bedienungsanleitung

Pioneer

Pioneer DEH-P3550MP XM Bedienungsanleitung

Lasonic

Lasonic MSU-2020 Bedienungsanleitung

THOMSON

THOMSON RCD150 Bedienungsanleitung

Denon

Denon DCD-1420 Bedienungsanleitung

Panasonic

Panasonic SJ-MR100 Bedienungsanleitung

Onkyo

Onkyo DX-7210 Bedienungsanleitung

Sony

Sony MZ-R3 Bedienungsanleitung

Denon

Denon DVM-4800 Bedienungsanleitung

JBL

JBL MR-32 Bedienungsanleitung

RCA

RCA RCD152 Bedienungsanleitung

Technics

Technics SL-PS770A Bedienungsanleitung

Clarion

Clarion compact disc Bedienungsanleitung

Sony

Sony MZ-M10 Bedienungsanleitung

Rotel

Rotel RCD 975 Bedienungsanleitung

Pioneer

Pioneer CLD-D790 Bedienungsanleitung

Optimus

Optimus CD-8250 Bedienungsanleitung

Audiovox

Audiovox CE101A - annexe 1 Bedienungsanleitung