Philips 71361 Original Betriebsanleitung

Strand Lighting Offices

The material in this manual is for information purposes only and is subject to change without notice.

Strand Lighting assumes no responsibility for any errors or omissions which may appear in this manual.

For comments and suggestions regarding corrections and/or updates to this manual, please contact your

nearest Strand Lighting office.

El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso.

Strand Lighting no asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier

comentario, sugerencia o corrección con respecto a este manual, favor de dirijirlo a la oficina de Strand

Lighting más cercana.

Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten.

Strand Lighting uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch

auftreten. Für Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen

und/oder Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten

Strand Lighting-Niederlassung aufzunehmen.

Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis.

La compagnie Strand Lighting n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans

ce manuel. Pour tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce

manuel, veuillez s'll vous plait contacter le bureau de Strand Lighting le plus proche.

Information contained in this document may not be duplicated in full or in part by any person without

prior written approval of Strand Lighting. Its sole purpose is to provide the user with conceptual

information on the equipment mentioned. The use of this document for all other purposes is specifically

prohibited. Certain features of the equipment described in this document may form the subject of patents

or patent applications.

Document Number: 2-450226-010

Version as of: 09 May 2011

LightPack LED Module Installation & Operation Guide

Strand Lighting - Dallas

10911 Petal Street

Dallas, TX 75238

Tel: 214-647-7880

Fax: 214-647-8031

Strand Lighting - New York

267 5th Ave, 4th Floor

New York, NY 10016

Tel: 212-213-8219

Fax: 212-532-2593

Strand Lighting - Asia Limited

Room 6-10, 20/F Delta House 3 On Yiu Street

Shatin, N.T. Hong Kong

Tel: + 852 2757 3033

Fax: + 852 2757 1767

Strand Selecon - Auckland

19-21 Kawana Street

Northcote, Auckland 0627

New Zealand

Tel: +64 9 481 0100

Fax: +64 9 481 0101

Strand Lighting - Europe

Marssteden 152

Enschede 7547 TD

The Netherlands

Tel: +31 53 4500424

Fax: +31 53 4500425

Website:

www.strandlighting.com

LightPack LED Module Installation & Operation Guide

Important Safeguards

When using electrical equipment, basic safety precautions should always be followed

including the following:

a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

b. Do not use outdoors.

c. Do not mount near gas or electric heaters.

d. Equipment should be mounted in locations and at heights where it will not

readily be subjected to tampering by unauthorized personnel.

e. The use of accessory equipment not recommended by the manufacturer

may cause an unsafe condition.

f. Do not use this equipment for other than intended use.

g. Refer service to qualified personnel.

SAVE THESE INSTRUCTIONS.

WARNING: You must have access to a main circuit breaker or other power

disconnect device before installing any wiring. Be sure that power is disconnected

by removing fuses or turning the main circuit breaker off before installation.

Installing the device with power on may expose you to dangerous voltage and

damage the device. A qualified electrician must perform this installation.

WARNING: Refer to National Electrical Code® and local codes for cable

specifications. Failure to use proper cable can result in damage to equipment or

danger to persons.

WARNING: To reduce the risk of fire or shock hazard, do not expose this

equipment to rain or moisture.

Installation & Operation Guide LightPack LED Module

TABLE OF CONTENTS

Strand Lighting Offices......................................................................... Inside Front Cover

Important Safeguards........................................................................................................ 1

TABLE OF CONTENTS ..........................................................................................................2

PREFACE .................................................................................................................................3

About this Guide............................................................................................................... 3

ACCESSORIES ........................................................................................................................3

Clamps .............................................................................................................................. 3

DMX512 Termination....................................................................................................... 3

OVERVIEW .............................................................................................................................4

INSTALLATION ......................................................................................................................5

Wall Mounting.................................................................................................................. 5

Pipe Mounting................................................................................................................... 5

CONNECTING POWER ..........................................................................................................6

CONNECTING DATA .............................................................................................................6

DMX512 Connections ...................................................................................................... 6

LED Luminaire Port Connections..................................................................................... 6

SETTING MODES AND DMX512 ADDRESS ......................................................................7

OPERATION ............................................................................................................................8

LightPack LED Controller - Status LED Indicators......................................................... 8

Focus / Bump Button Operation ....................................................................................... 8

Luminaire Discovery......................................................................................................... 8

SPECIFICATIONS ...................................................................................................................9

LightPack LED Module Installation & Operation Guide

PREFACE

About this Guide

The document provides installation and operation instructions for the following products:

• 71361 – LightPack LED 120V, Grounded Stage Pin Connector (GP)

• 71362 – LightPack LED 120V, Twistlock Connector (GTL)

• 71363 – LightPack LED 120V, Edison Connector (GR)

• 71364 – LightPack LED 230V, Bare Leads (no AC input connector installed)

Please read all instructions before installing or using this product. Retain this guide

for future reference.

IMPORTANT INFORMATION. PLEASE READ!

This unit is intended for installation in accordance with the National Electric Code® and local

regulations. It is also intended for indoor applications only. Before any electrical work is

performed, disconnect power at the circuit breaker or remove the fuse to avoid shock or

damage to the control. It is recommended that a qualified electrician perform this installation.

Observe the following precautions when installing, operating or servicing the product:

• Disconnect power before servicing.

• Install in dry locations only.

• DO NOT power module from a dimmed source. Connect to standard power or

mechanical relay ONLY.

• Use the included safety cable for ALL installations.

• If installing any other type of mounting hardware or bracket, DO NOT use screws

longer than 1/4" in length. Longer screws WILL damage interior electrical components.

ACCESSORIES

The following accessories are available for the LightPack LED Module from your Authorized

Strand Lighting Dealer. Note, all accessories are sold separately.

Clamps

DMX512 Termination

Part Number Description

SC Pipe Clamp

71351 Cheeseboro Clamp

Part Number Description

71346 DMX512 Terminator

Installation & Operation Guide LightPack LED Module

OVERVIEW

LightPack LED controller delivers power and control to any Philips Selecon PL Wash

luminaire or Philips Color Kinetics Color Blast wash lights. Smart addressing technology

simplifies set up and allows users to quickly address any luminaire regardless of type. Users

set an address, select an operating mode and press a button to set up any connected luminaire.

Each output is configured to match the luminaire regardless of the number of colors the unit

supports and delivers exactly the right number of control channels needed. An intensity

channel set up option is also available to make your luminaires even easier to use and

program.

CAUTION: The LightPack LED Module is for use with specified LED luminaires

only. NOT FOR USE WITH SCROLLERS. For luminaire types, refer to

"SPECIFICATIONS" on page 9.

Figure 1: LightPack LED Module Overview

3 4

27 8 9

SIDE VIEW

END VIEW END VIEW

1- Heatsink

2- AC Input Cable

3- DMX 512 In

4- DMX512 Thru/Out

5- Focus / Bump Button (one for each luminaire port)

6- Red and Green Status Indicators (one set for each luminaire port)

7- Mode Settings (one 4-position DIP switch)

8- DMX512 Address Setting (three rotary DIP switches)

9- LED Luminaire Control Port (two each, power and data supplied)

LightPack LED Module Installation & Operation Guide

INSTALLATION

The LightPack LED Module can be mounted in a variety of configurations. Depending on

your requirements, choose one of the methods shown below. The LightPack LED Module can

be mounted vertically (recommended) or horizontally as required, however, to allow for

optimum convection cooling, the module cannot be mounted with the heatsink fins downward.

WARNING: A non-removable safety cable is supplied with the unit. The safety cable

must be attached to a secure structure and may be required by local or national codes.

Wall Mounting

The LightPack LED Module can be mounted to a wall. Note that the wall mounts (with

screws) are included with unit. Wall anchoring hardware is by others. The unit must be

mounted with the heatsink fins up/down so the unit will dissipate heat properly. Mounting to

wall must comply with local and national codes.

Figure 2: LightPack LED Module Wall Mounting

Pipe Mounting

The LightPack LED Module can be mounted on pipe or truss. Note that the pipe mount (with

screws) are included with unit. Clamps are sold separately or by others (See “Clamps” on

page 3 for ordering information). The unit must be mounted with the heatsink fins up/down so

the unit will dissipate heat properly. Mounting to pipe or truss must comply with local and

national codes.

Figure 3: LightPack LED Module Pipe or Truss Mounting

Wall Mount Bracket (x2)

Note heatsink orientation.

Mount as shown for proper

cooling. Bracket Mounting

Screws (x4)

Wall Mount Brackets*

Note heatsink orientation.

Mount as shown for proper

cooling.

Pipe Mount Bracket

Bracket Mounting

Screws (x4)

*As an option, you can reverse the wall

mount brackets and install them as shown

for storage purposes. If the wall mount

brackets are installed in this fashion, all

four mounting screws are used.

Installation & Operation Guide LightPack LED Module

CONNECTING POWER

The LightPack LED Module is supplied with an AC input cable. Some versions are sold with

AC input connectors installed.

WARNING: DO NOT power module from a dimmed source. Connect to standard

power or mechanical relay ONLY.

Figure 4: AC Power Connectioning.com

CONNECTING DATA

DMX512 Connections

The LightPack LED Module supports standard USITT DMX512/1990 protocol. A termination

plug (Strand # 71346) is required at the last module in the data link.

Figure 5: DMX512 Connections

LED Luminaire Port Connections

The LightPack LED Module

supports the control of two LED

luminaires through its two LED

Luminaire ports.

To AC Power

AC Input Wiring - 230V Models

Wire Color Description

Brown Line

Blue Neutral

Green/Yellow Ground

AC Input Wiring - 120V Models

Wire Color Description

Black Line

White Neutral

Green Ground

DMX 5-Pin Connectors Pinout:

Pin Signal

1 Common (Drain)

2 DMX512 -

3 DMX512 +

4 No Connection

5 No Connection

DMX512 Out/Thru Cable

or Termination Plug

DMX512 In Cable

LED Module 4-Pin Connector Pinout:

Pin Signal

1+24VoltsDC

2NotUsed

3Data

4 Ground

Figure 6: LED Luminaire Connections

WARNING: The LightPack

LED Module is only for use with

certain LED luminaires. See

"SPECIFICATIONS" on page 9

for more information.

LightPack LED Module Installation & Operation Guide

SETTING MODES AND DMX512 ADDRESS

The operating modes and DMX512 address can be easily configured using the controls located

inside the recess panel. There is one 4-position DIP switch (Configuration Switch) to

configure the modes and three rotary DIP switches to configure the DMX512 address.

For example (as shown in Figure 7), to set a DMX512 address of 471, set the 100’s dial to "4",

the 10’s dial to "7", and the 1’s dial to "1". To configure the modes, set each of the DIP

switches to either the ON or OFF setting (up or down).

Figure 7: DIP Switches

To program individual DMX512 address, 8/16 Bit Mode, and Intensity Channel for each

connected luminaire:

Step 1. At Configuration Switch, set Switch 4 to “ON”.

Step 2. At Configuration Switch, set 8 /16 Bit Mode and Intensity channel switches as

desired.

Step 3. Set each DMX address dial to desired DMX512 address for first luminaire.

Step 4. Press and hold Focus / Bump button until first luminaire flashes.

Step 5. Set each DMX address dial to desired DMX512 address for second luminaire.

Step 6. Press and hold Focus / Bump button until second luminaire flashes (about 5

seconds).

Step 7. When programming is complete, at Configuration Switch, set Switch 4 to “OFF”.

Configuration Switch

ON = Program On

OFF = Program Off

For Future Use

ON = Intensity Channel On

OFF = Intensity Channel Off

ON = 16-Bit Mode

OFF = 8-Bit Mode

DMX512 Address Switches

000 = DMX Disabled (only

Focus / Bump Button active)

001 - 512 = DMX512 Address

Installation & Operation Guide LightPack LED Module

OPERATION

The LightPack LED Module will power up when the AC power is connected. (NOTE: the

LightPack LED Module does not have a main on/off switch.)

The LightPack LED Module provides two LED status indicators and a Focus/Bump buttons.

LightPack LED Controller - Status LED Indicators

The two LEDs associated with each channel report various operating conditions.

Focus / Bump Button Operation

Once each luminaire has been set up, tap the Focus / Bump button once to turn on all of the

LEDs on the attached luminaire. Each successive Button tap will advance through each LED

color that the Luminaire offers. The final tap will turn the luminaire off.

Luminaire Discovery

The LightPack LED Module is set, by default, for RGBAW LED luminaire operation. If you

plug in an RGB or WW LED luminaire, you will need to cycle through the Focus / Bump

button presses (as described in “Focus / Bump Button Operation”) to return to the first color.

The LightPack LED Module can "discover" and set itself to control the type of connected

luminaire.

To Discover the connected luminaire:

Step 1. Connect luminaire to LightPack LED Module. Note, LightPack LED Module must

be powered.

Step 2. Press and hold Focus / Bump button for 5 seconds.

Step 3. The luminaire will flash through all colors and stop.

Step 4. The LightPack LED Module is now set to connected RGB or WW luminaire.

Red LED Green LED Condition

On Off No DMX512 Communications

Off / On On Module is set to 100% by Focus / Bump button

Button Tap RGBAW Luminaire RGB Luminaire WW Luminaire

1 All On All On All On

2Red RedWarmWhite

3 Green Green Cool White

4 Blue Blue Off

5Amber Off

6White

7Off

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips DJ-Equipment Handbücher

Philips

Philips ColorReach Compact Powercore Bedienungsanleitung

Philips

Philips VL1000 TS Bedienungsanleitung

Philips

Philips VARI-Lite VL4000 Bedienungsanleitung

Philips

Philips 91816 Light Palette Classic 1500 Bedienungsanleitung

Philips

Philips C-Splash 2 Bedienungsanleitung

Philips

Philips Soundmachine PX5112T Bedienungsanleitung

Philips

Philips VARI-LITE VL6000 Beam Luminaire Bedienungsanleitung

Philips

Philips ColorBlaze TRX Bedienungsanleitung

Philips

Philips VL550 Bedienungsanleitung

Philips

Philips SELECON PL3 Bedienungsanleitung

Philips

Philips SELECON PLPROFILE4 MKII Bedienungsanleitung

Philips

Philips IP65 Bedienungsanleitung

Philips

Philips VARI LITE VLZ SPOT Luminaire Bedienungsanleitung

Philips

Philips DS8900 Bedienungsanleitung

Philips

Philips VARIOLITE VL6000 Bedienungsanleitung

Philips

Philips ColorBlaze TR4 Bedienungsanleitung

Philips

Philips IP20 Bedienungsanleitung

Philips

Philips VARI-Lite VL4000 Bedienungsanleitung

Philips

Philips SELECON AUREOL Installationshandbuch

Philips

Philips SELECON PLPROFILE4 MKII Bedienungsanleitung

Philips

Philips Chromacore Optibin ColorBlast TR Bedienungsanleitung

Philips

Philips Showline SL SUNLED 10 Bedienungsanleitung

Philips

Philips Showline SL STRIP 10IP Bedienungsanleitung

Philips

Philips AZ8030 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung